Luminance Brands RIPTIDE CF605BQ00 User manual

Part No. F40BP75720002 Form No. BP7572-2
Revision: 02152021 U.L. Model No.: CF605
52” Wet Location
Ceiling Fan Owner’s Manual
RIPTIDE
CF605BQ00
Barbeque Black
CF605GRT00
Graphite
Model Numbers
Net Weight: 19.4 Lbs.
CF605ORB00
Oil Rubbed Bronze
CF605SW00
Satin White
• Español - página 37
• Français - page 73
READ AND SAVE THESE INSTRUCTIONS
INDOOR/OUTDOOR
1-800-777-4440
Questions, problems, missing parts: Before returning to the store, Call Customer Service
www.luminancebrands.com

Table of Contents
2
U.L. Model No.: CF605
Section Page
Safety Instructions ................................ 2
1. Unpacking Instructions ..........................3-4
2. Electrical Requirements .......................... 4
3. Ceiling Fan Assembly ..........................5-14
4. How to Hang Your Ceiling Fan ..................15-16
5. How to Wire Your Ceiling Fan ..................17-21
6. Final Assembly ................................ 22
7. Remote Control Procedures ....................23-25
8. Reverse Switch Operation........................ 26
9. Installation of No-Light Cover (Sold Separately) .....27-29
Section Page
10. Maintenance ................................. 30
11. Accessories ................................. 30
12. Remote Control Troubleshooting ................. 30
13. Troubleshooting .............................. 31
14. Repair Parts ...............................32-33
15. Energy Efficient Use of Ceiling Fan ............... 34
Ceiling Fan Limited Warranty ....................... 35
Spanish ........................................ 37
French ........................................ 73
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring, and do not operate fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed
controls.
NOTE: All set screws must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To reduce the risk of fire or electrical shock, this fan
should only be used with fan speed control, Model No.
UC7067RAI, manufactured by Rhine Electric Co., Ltd.
To avoid fire, shock or injury, do not use a Luminance
Brands or any other brand of control not specifically
approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury or
property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!

1. Unpacking Instructions
3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-777-4440
WARNING
!
1.1
Open Carton containing the Fan. Remove top half of
styrofoam unit. Remove Parts and check to see that
you have received the following Hardware and Parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local retailer
or catalog outlet for replacement before proceeding.
E
A
F
D
G
K
H
I
J
B
C
PACKAGE CONTENTS
HARDWARE CONTENTS
Part Description Quantity
1 Wire Connectors, 12 ga. 3
2 Clevis Pin 1
3 Hairpin Clip 1
4 Threaded Stud, #8-32 x 1-1/4” 2
5 Knurled Knobs, #8-32 2
6 Lockwashers, External Tooth #8 2
7 #10-24 x 10 mm Flat Head Screws 10
8 #8-32 x 10 mm Serrated Pan Head Screw (spare) 1
9 Blade Balance Kit 1
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Cover 1
C Upper Housing 1
D Light Kit Adapter 1
E Blades 3
F LED Light Fixture Assembly 1
G Shade 1
H Hanger Bracket 1
I Hanger Ball / 8” Downrod Assembly 1
J Remote Control Receiver and Hardware 1
K Remote Control Transmitter, SR401
with Wall Bracket and Hardware 1
7
4
8
9
3
2
6
5
1

4
U.L. Model No.: CF605
1. Unpacking Instructions (Continued)
2. Electrical Requirements
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
Your new Ceiling Fan will require a Grounded Electrical
Supply Line of 120 Volts AC, 60 Hz, 15 Amp Circuit.
The Outlet Box MUST be securely Anchored and
capable of withstanding a Load of at least 50 Pounds.
IMPORTANT: Your ceiling fan will not function
properly, and may be damaged, if used with any
wall dimmer switch or control other than the
Luminance Brands Electric Fan/Light Remote
Control supplied with the fan.
If your Fan is to replace an Existing Ceiling Light
Fixture, turn Electricity OFF at the Main Fuse Box
or Circuit Breaker Panel at this time and remove the
existing Light Fixture.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One Wire Stripper One Wire Cutter
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Your Luminance Brands Ceiling Fan comes supplied
with a Fan/Light Remote Control which consists of
a Receiver mounted inside the Ceiling Cover.
This system allows you to regulate your Ceiling Fan
Speed and Light ON/OFF.
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 17).
If you feel you do not have enough wiring knowledge
or experience, have your fan installed by a licensed
electrician.
WARNING
!
THIS FAN MODEL IS SUITABLE FOR WET LOCATIONS
SUCH AS PORCHES, PATIOS, AND DECKS.
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan

5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly
STYROFOAM
FAN MOTOR
ASSEMBLY
Figure 1
3.1
Remove the Fan Motor Assembly from the protective
plastic bag.
Place the Fan Motor Assembly, Bottom side facing up,
onto both styrofoam forms from the carton (Figure 1).
The styrofoam forms serves as a holder for the Fan
during the first stages of assembly.
REMOVE ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
FAN MOTOR
ASSEMBLY
LOOSEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
Figure 2
3.2
Remove and Retain One of the Three #8-32 x 10mm
Serrated Pan Head Screws from the Fan Motor
Assembly.
Loosen the remaining Two #8-32 x 10 mm Serrated
Pan Head Screws (Figure 2).

3. Ceiling Fan Assembly (Continued)
6
U.L. Model No.: CF605
LIGHT KIT
ADAPTER
TURN LOWER ADAPTER
CLOCKWISE
ENGAGE TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
MOTOR
COUPLER
Figure 3
REINSTALL ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
LIGHT KIT
ADAPTER
RETIGHTEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
3.4
Reinstall the previously removed #8-32 x 10 mm
Serrated Pan Head Screw into the Light Kit Adapter
(Figure 4).
Secure the Light Kit Adapter by tightening the Three
#8-32 x 10 mm Serrated Pan Head Screws (Figure 4).
A spare #8-32 x 10 mm Serrated Head Pan Screw
supplied in parts bag, if needed.
Figure 4
3.3
Place the Wires and Connectors through the Center
Hole of the Light Kit Adapter.
Position the Light Kit Adapter onto the Fan Motor
Assembly Loosened Screws.
NOTE: For Ease of Light Kit Adapter Installation:
Hold the Motor Coupler, located at the underside of
the Fan Motor Assembly while installing the Light
Kit Adapter.
Rotate the Light Kit Adapter Clockwise to Engage the
Two loosened #8-32 x 10 mm Serrated Pan Head
Screws in the Two Key Slots (Figure 3).

7
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
FAN MOTOR
ASSEMBLY
WHITE WIRE
LED LIGHT FIXTURE
ASSEMBLY
LED LIGHT FIXTURE
ASSEMBLY BLACK
WIRE
LED LIGHT FIXTURE
ASSEMBLY WHITE
WIRE
FAN MOTOR
ASSEMBLY
BLUE WIRE
Figure 5
3.5
Securely connect the LED Light Fixture Assembly
White Wire Terminal to the Fan Motor Assembly White
Wire Terminal (Figure 5).
Securely connect the LED Light Fixture Assembly Black
Wire Terminal to the Fan Motor Assembly Blue Wire
Terminal (Figure 5).
To reduce the risk of electric shock, disconnect the
electrical supply circuit to the fan before installing
light fixture.
CAUTION
!
NOTE: If Installing the Ceiling Fan without the LED Light Fixture Assembly,
Skip Sections 3.5 - 3.8 and Complete 3.9 - 3.18.
Section 9, Installation of No-Light Cover (Sold Separately) will replace the LED Shade.

REMOVE ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
LIGHT KIT
ADAPTER
LOOSEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
Figure 6
3.6
Remove and Retain One of the Three #8-32 x 10 mm
Serrated Pan Head Screws from the Light Kit Adapter.
Loosen the remaining Two #8-32 x 10 mm Serrated
Pan Head Screws (Figure 6).
3. Ceiling Fan Assembly (Continued)
8
U.L. Model No.: CF605
REINSTALL ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
MOTOR
COUPLER
RETIGHTEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
LED LIGHT FIXTURE
ASSEMBLY
TURN LED
CLOCKWISE
Figure 7
3.7
Tuck wires into the LED Light Fixture Assembly and
position on the Light Kit Adapter Assembly.
NOTE: For Ease of LED Light Fixture Assembly
Installation: Hold the Motor Coupler, located at
the underside of the Fan Motor Assembly while
installing the LED Light Fixture Assembly.
Rotate the LED Light Fixture Assembly Clockwise to
Engage the Two loosened #8-32 x 10 mm Serrated
Pan Head Screws in the Two Key Slots (Figure 7).
Reinstall the One previously removed #8-32 x 10 mm
Serrated Pan Head Screw (Figure 7).
Secure the LED Light Fixture Assembly by tightening
the Three #8-32 x 10 mm Serrated Pan Head Screws
(Figure 7).
A spare #8-32 x 10 mm Pan Head Screw is supplied in
parts bag, if needed.
To avoid possible fire or shock, do not pinch wires
between the light kit adapter and the LED light fixture
assembly.
WARNING
!

9
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
3.8
NOTE: For Ease of Shade Installation: Hold the
Motor Coupler, located at the underside of the Fan
Motor Assembly while installing the Shade.
Place the Shade into the opening in the Light Kit
Adapter, aligning the Three Flat Areas on the top edge
of the Shade with the Light Kit Adapter Three Raised
Dimples.
Turn the Shade Clockwise until it stops (Figure 8).
NOTE: Periodically check that the Shade is seated
fully clockwise in the Light Kit Adapter.
Carefully turn the partially assembled Ceiling Fan right
side up and place the Fan securely into the packing
styrofoam.
MOTOR
COUPLER
TURN SHADE CLOCKWISE
LIGHT KIT ADAPTER
RAISED DIMPLES (3)
SHADE FLAT
AREAS (3)
SHADE
Figure 8

10
3. Ceiling Fan Assembly (Continued)
PHILLIPS HEAD SET SCREW (LOOSENED)
HANGER BALL
DOWNROD
PIN
GREEN GROUND WIRE
Figure 9
3.9
Remove the Hanger Ball by loosening the Phillips Head
Set Screw in the Hanger Ball until the Ball falls freely
down the 8” Downrod (Figure 9).
Remove the Pin from the Downrod, then remove the
Hanger Ball (Figure 9).
Retain the Pin and Hanger Ball for reinstallation in
Step 3.16.
NOTE: Do not loosen the Screw that attaches the
Green Ground Wire to the Hanger Ball.
DOWNROD
THREE 80" MOTOR
WIRES (UNTWISTED)
Figure 10
3.10
Separate, untwist and unkink the Three 80” Motor
Wires.
Route the Three 80” Black, Blue, and White Motor
Wires through the 8” Downrod (Figure 10).
U.L. Model No.: CF605

11
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
MOTOR
COUPLER
LOOSEN SET
SCREWS (2)
DOWNROD
Figure 11
3.11
Loosen the Two Phillips Head Set Screws in the Motor
Coupler for installation of the 8” Downrod (Figure 11).
Seat the Downrod in the Motor Coupler (Figure 11).
Rotate and align the Downrod holes with the Two Holes
in the Motor Coupler (Figure 11).
MOTOR
COUPLER
CLEVIS
PIN
HAIRPIN
CLIP
HAIRPIN
CLIP
CLEVIS
PIN
Figure 12
3.12
Align the Clevis Pin Holes in the 8” Downrod with the
Holes in the Motor Coupler.
Install the Clevis Pin and secure with the Hairpin Clip
(Figure 12).
The Clevis Pin must go through the Motor Coupler
Holes. It is critical that the Clevis Pin in the Motor
Coupler is properly installed and securely tightened.
It is critical that the clevis pin in the motor coupler
is properly installed. Failure to verify that the pin is
properly installed could result in the fan falling.
WARNING
!

12
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
RETIGHTEN TWO
PHILLIPS HEAD
SET SCREWS
MOTOR
COUPLER
Figure 13
3.13
While pulling up on the 8” Downrod, retighten the Two
Phillips Head Set Screws to secure the Downrod in the
Motor Coupler (Figure 13).
NOTE: The Set Screws must be properly installed
as described above, or fan wobble could result.
It is critical that the set screws in the motor coupler are
properly installed and securely tightened. Failure to
verify that the set screws are properly installed could
result in the fan falling.
WARNING
!
GROMMET
UPPER HOUSING
DOWNROD
Figure 14
3.14
Make sure the Grommet is properly installed in the
Upper Housing, then slide the Upper Housing on the
8” Downrod until it rests on the Motor Coupler
(Figure 14).
DOWNROD
CEILING
COVER
Figure 15
3.15
Place the Ceiling Cover over the 8” Downrod
(Figure 15).
Be sure that the Ceiling Cover and the Upper Housing
are both oriented correctly (Figure 15).

13
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
PIN
DOWNROD
HANGER BALL
SET SCREW
Figure 16
3.16
Route the Three Motor Wires through the Hanger Ball
(Figure 16).
Reinstall the Hanger Ball on the 8” Downrod as follows:
Position the Pin through the Two Holes in the
Downrod and align the Hanger Ball so the Pin is
captured in the Groove in the top of the Hanger Ball
(Figure 16).
Pull the Hanger Ball up tight against the Pin and
securely retighten the Phillips Head Set Screw in the
Hanger Ball (Figure 16).
A loose Phillips Head Set Screw could create fan
wobble.
BLACK WIRE
6 TO 9
INCHES
BLUE WIRE
WHITE WIRE
HANGER
BALL
1/2
INCH
Figure 17
3.17
The Fan comes with Black, Blue and White Wires that
are 80-inches long.
Before installing the Fan, measure up approximately
6 to 9-inches above top of Hanger Ball/Downrod
Assembly (Figure 17).
Cut off excess Wires and strip back insulation 1/2-inch
from end of Wires.

3. Ceiling Fan Assembly (Continued)
14
U.L. Model No.: CF605
#10-24 x 10 mm FLAT HEAD
SCREWS (3 per blade)
GROOVES (2 per flange)
BLADES (3)
SIDE VIEW OF BLADE
BLADE ALIGNMENT TABS
Figure 18
3.18
Position the Fan Blade with the Two Alignment Tabs
facing Down for installation into the Two Grooves on
top of the Flange. (see Figure 18 enlargement).
Slide a Blade, holes facing up, onto the flange and seat
against the Fan Motor Assembly.
Mount the Blade to the Flange using Three
#10-24 x 10 mm Flat Head Screws (supplied)
(Figure 18).
NOTE: Take care not to scratch Fan Motor
Assembly when installing Blades.
Complete the remaining Two Blades installation per the
above instructions.
A spare #10-24 x 10 mm Flat Head Screw is supplied in
the loose parts bag, if required.
To reduce the risk of personal injury, do not bend
the blades during installation, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
WARNING
!

15
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
4.1
Disconnect Electrical Power to the Branch Circuit at
the Circuit Breaker Panel or Main Fuse Box before
attempting to install the Ceiling Fan to the Outlet Box
(Figure 20).
MAIN FUSE BOX
OR CIRCUIT
BREAKER PANEL
On/I On/I On/I On/I
On/I On/I On/I On/I
Figure 20
FLOOR
CEILING
AT
LEAST
7'
Figure 19
4. How to Hang Your Ceiling Fan
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor (Figure 19).
CAUTION
!

16
U.L. Model No.: CF605
4.2
Securely attach the Hanger Bracket to the Outlet Box
using the Two Screws supplied with the Outlet Box
(Figure 21).
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
OUTLET
BOX
ANTI-ROTATION TAB
Figure 21
4. How to Hang Your Ceiling Fan (Continued)
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
HANGER BRACKET
HANGER BALL
HANGER BALL
GROOVE
ANTI-ROTATION TAB
4.3
Carefully lift the Fan and seat the Hanger Ball/
Downrod Assembly on the Hanger Bracket that was
just attached to the Outlet Box (Figure 22).
Be sure the Groove in the Ball is engaged with the
Anti-Rotation Tab on the Hanger Bracket (Figure 22).
Figure 22

17
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
To avoid possible fire or shock, do not pinch the
antenna wire between the hanger bracket and the
receiver.
WARNING
!
TO MOTOR L
RECEIVER ANTENNA WIRE
AC IN L
RECEIVER
FOR LIGHT
AC IN N
TO MOTOR N
Figure 23
5.2
Locate the Electronic Receiver and insert its Antenna
Wire into the opening of the Hanger Bracket above
the Hanger Ball. Continue to insert the body of the
Receiver (flat side facing up) into the opening, orient as
shown. Be careful not to pinch any wires between the
Receiver body and the Bracket or Ball (Figure 23).
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
5.1
Disconnect Electrical Power to the Branch Circuit at
the Circuit Breaker Panel or Main Fuse Box before
attempting to wire the Ceiling Fan.
5. How to Wire Your Ceiling Fan
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box or circuit breaker
panel before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
!
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
To reduce the risk of electrical shock, disconnect the
electrical supply circuit before installing the fan, light
kit or receiver.
CAUTION
!

18
U.L. Model No.: CF605
5. How to Wire Your Ceiling Fan (Continued)
5.3
NOTE: Make all wiring connections using the
wire connectors supplied in the hardware kit and
receiver parts bag. Make sure that all connections
are tight, including ground, and that no bare wire is
visible at the wire connectors, except for the supply
circuit ground wire.
Connect the Green Ground Wire from the
Hanger Ball and the Green Ground Wire from the
Hanger Bracket to the Ground Conductor of Supply
(this may be a bare wire or wire with Green Colored
insulation). Securely connect Wires with the 12 ga.
Wire Connector (supplied in parts bag) (Figure 24).
TO MOTOR L
TO MOTOR N
FOR LIGHT
AC IN L
SUPPLY & RECEIVER
WHITE WIRES
12 ga. WIRE
CONNECTOR
AC IN N
Figure 25
5.4
Securely connect the Receiver White Wire (AC IN N) to
the Supply White Wire (neutral) using the 12 ga. Wire
Connector (supplied in parts bag) (Figure 25).
TO MOTOR L
TO MOTOR N
FOR LIGHT
AC IN L
HANGER BALL, HANGER BRACKET, & SUPPLY GREEN
GOUNDING WIRES
12 ga. WIRE
CONNECTOR
AC IN N
Figure 24
GROUND WIRES

19
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
5. How to Wire Your Ceiling Fan (Continued)
5.5
Securely connect the Receiver Black Wire (AC IN L)
to the Supply Black Wire (hot) using the 12 ga. Wire
Connector (supplied in parts bag) (Figure 26).
TO MOTOR L
TO MOTOR N
FOR LIGHT
AC IN N
12 ga. WIRE
CONNECTOR
SUPPLY & RECEIVER
BLACK WIRES
AC IN L
Figure 26
TO MOTOR L
FOR LIGHT
AC IN N
18 ga. WIRE
CONNECTOR
AC IN L
TO MOTOR N
FAN & RECEIVER
WHITE WIRES
Figure 27
5.6
Securely connect the Receiver White Wire
(TO MOTOR N) to the Fan Motor White Wire using the
18 ga. Wire Connector (supplied with the receiver)
(Figure 27).

20
U.L. Model No.: CF605
5. How to Wire Your Ceiling Fan (Continued)
5.7
Securely connect the Receiver Black Wire
(TO MOTOR L) to the Fan Motor Black Wire using the
18 ga. Wire Connector (supplied with the receiver)
(Figure 28).
5.8
Securely connect the Receiver Blue Wire (TO LIGHT)
to the Fan Motor Blue Wire using the 18 ga. Wire
Connector (supplied with the receiver) (Figure 29).
Position the Antenna Wire on top of the Receiver. Slide
the RCFP Receiver completely onto the Hanger Ball,
nestled in the Hanger Bracket (Figure 29).
FOR LIGHT
AC IN N
18 ga. WIRE
CONNECTOR
AC IN L
TO MOTOR N
FAN & RECEIVER
BLACK WIRES
TO MOTOR L
Figure 28
AC IN N
18 ga. WIRE
CONNECTOR
AC IN L
TO MOTOR N
TO MOTOR L
FAN & RECEIVER
BLUE WIRES
FOR LIGHT
Figure 29
NOTE: Failure to properly connect the Receiver
Wires will damage the device and render it non-
operable.
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the supply circuit ground wire.
Do not operate fan until blades are in place.
Noise and fan damage could result.
WARNING
!