Lumineux 421301 User manual

READ THESE INSTRUCTIONS
THOROUGHLY BEFORE
INSTALLATION KEEP THESE
INSTRUCTIONS FOR
FUTURE REFERENCE.
IMPORTANT:
This product must be installed
by a qualifi ed electrician or
competent person, and in
accordance with current building
and IET wiring regulations.
• Light Fitting
• Instruction Manual
Fontburn Emergency
2in1 Exit Sign
Surface Mount & Hanging
3W
Technical Helpline: [phone]
www.lumineux.co.uk
1 2
5
3
6
on
off
4
Fontburn
Emergency
1. Push in the two release tabs to separate the
mounting bracket with terminal block from the
gear-tray housing. (1)
2. Unplug the cable from the gear-tray.
3. Secure the mounting bracket into position, passing
the mains cable through the cable entry. (2)
4. Connect the cables to the terminal block as shown
in the diagram. (3)
5. Connect the battery. (4)
6. Return the gear-tray back into position ensuring
no cables are trapped and the locking tabs
are engaged.
7. To  t the emergency decal place in position and
use the 2 part plastic rivets to retain into position. (5)
8. When wall mounting rotate the gear-tray with decal
in one direction only. (6)
TOOLS REQUIRED
BOX CONTENTS
• Drill
• Screwdriver
• Cable
INSTALLATION INSTRUCTIONS
on
off
This lighting  xture has been properly
packed to avoid damage during
transit. Before commencing with the
installation carefully inspect the
luminaire to con rm there is no
damage. DO NOT INSTALL if any
damage has occurred to the  xture
or any of its components.
• Turn off the mains power before performing
inspections, installation, or removal
• Verify that the supply voltage is correct by
comparing it with the luminaire label information
• It is the installers responsibility to ensure installation
is suitable for the total load of the luminaire(s). The
supply cable, fuses/circuit brakers must be correctly
rated for the electrical load and considering for any
transient inrush currents that may occur
• Do not perform insulation strength or resistance
tests on installed luminarie(s) connected
PLEASE READ THESE INSTRUCTIONS
BEFORE INSTALLATION.
WARNING: Risk of electric shock! Isolate
the mains power before proceeding.
Manby Business Park, Manby, Lincolnshire, LN11 8UT
Lumineux is a B&T Associates Ltd company.
Self-Test
IP20
Warranty
5 YR
Battery
Warranty
2 YR
6000K
L - LIVE (SW) = Brown
N - NEUTRAL = Blue
L1 - PERMANENT LIVE
(PL) = Black
- EARTH = Green/Yellow
Tab locations
Manby Business Park, Manby, Lincolnshire
R1.0 16072019
NON– EMERGENCY FITTINGS
CLASS I PRODUCT
EARTH CONNECTION
REQUIRED.
LIVE = Brown
NEUTRAL = Blue
GND = Green/Yellow
Product Specification:
Unit Input Voltage Waage Length Width Height LF(mm)
4 Single 220-240VAC, 50/60Hz 19W 1220 64 62 1016
4 Twin 220-240VAC, 50/60Hz 38W 1220 64 62 1016
5 Single 220-240VAC, 50/60Hz 27W 1524 64 62 1320
5 Twin 220-240VAC, 50/60Hz 50W 1524 64 62 1320
6 Single 220-240VAC, 50/60Hz 38W 1829 64 62 1625
6 Twin 220-240VAC, 50/60Hz 60W 1829 64 62 1625
Battery
Rotate 90º
Wall Mount
GG
A
G

ROUTINE TEST RECORD
Type Test Year 1 Year 2 Year 3 Year 4 Year 5
Signed Date Signed Date Signed Date Signed Date Signed Date
Functional 1
Functional 2
Functional 3
Functional 4
Functional 5
Functional 6
Functional 7
Functional 8
Functional 9
Functional 10
Functional 11
3hr Duration 12
Installation Engineers Contact Details: Luminaire Reference / Location
Name: Tel:
Luminaire Details: Full Recharge Duration 24 Hours Emergency Duration 3 Hours Lamp Type LED
Fontburn Emergency 2in1 Exit Sign
Emergency 0 to +30ºC
Technical Helpline: [phone]
DISPOSAL
PRODUCT TEMP SPECIFICATION
FONTBURN EXIT SIGN DIMENSIONS
Part No. Description Watts L(mm) W(mm) H(mm) Weight
421301 Exit Sign 3W 310 35 230 0.96Kg
421302 Exit Sign
Self-Test 3W 310 35 230 0.96Kg
421304 Hanging
Exit Sign 3W 300 45 700 0.98Kg
421311
Hanging
Exit Sign
Self-Test
3W 300 45 700 0.98Kg
Revision 2.0 - May 2022
This luminaire is warranted for a
period of 5 years from the date of
purchase**. The backup battery
pack in the emergency version
is warranted for a period of 24
months. The warranty could be
invalidated should the light tting
not be installed according to these
instructions, outside the scope of
the specication or the product
has been altered or tampered with
in any way. Please see website for
terms and conditions.
WARRANTY
Disassembly instructions for end of
life disposal available on website.
Disposal of Electronic Equipment
WEEE Directive 2002/96/EC This
product falls within the scope of
the Waste Electrical & Electronic
Equipment Directive (WEEE), which
means the product should not be
disposed of as normal household
waste. Please recycle where
facilities exist or check with your
Local Authority. RoHS – All
components and materials used in
this product are RoHS 2002/95/EC
compliant.
Specications may change from time
to time. The information contained
in this leaet is for guidance only
and should not be considered as
always accurate and should be
treated as not representative.
** Please see our website for more detailed information on warranty.
1. Connect incoming earth cable to ‘Earth’ terminal on connector block.
2. Connect incoming neutral cable to ‘Neutral’ terminal on connector block.
3. For the emergency unit to work correctly, please ensure that an
uninterrupted permanent live feed is present and is connected directly
to the ‘Permanent Live’ terminal of the mains terminal block. Please
ensure there are no switches, PIRs etc within the permanent live feed,
constant switching of the emergency pack could result in premature
battery failure.
4. Connect incoming switched live cable to the terminal marked
“Switched Live”
NOTE: If there is no switch live feed and the unit has a microwave sensor,
simply bridge across from the “Permanent Live” to the Switch Live” on the
mains terminal block.
5. There should be a loose ying lead connected to the battery. This needs
to be attached to the ying lead from the emergency control unit.
6. Following power up the green LED indicator should illuminate to indicate
charging. If power to the unit is disrupted or isolated, the unit indicating
green LED will switch off, triggering the emergency LEDs to illuminate.
7. Please allow 24 hours charge before rst emergency test.
The self-test version of emergency is tted with control gear that will carry out
periodic functional tests every 1 month and full duration test every 12 months.
Wiring instructions for units equipped
an with EMERGENCY function
Self-Test EMERGENCY function
Emergency lighting luminaries must be installed and maintained in
accordance with the emergency lighting standard BS 5266-1
Fault/Test/Status Reason
Battery fully charged
and operational Standard daily use
Battery Charging Initial charge /
battery topping up
Battery Failure Battery is disconnected or
damaged/faulty
Duration Test Failure Maintenance check required
by qualied engineer
Automatic Testing - Function
5 minute test (Every 30 days)
Self-testing in
operation
Automatic Testing -
Duration test is 3 hours
(every 12 months)
Self-testing in
operation
Charge Indicator Status
Battery Fully Charged
and Operational
Battery Charging
Auto Test 5 Min
(every 30 days)
Auto Test 3 Hours
(every 12 months)
Duration Test Failure
1 Sec ON
1 Sec OFF
3 Sec ON
3 Sec OFF
3 Sec ON
1 Sec OFF
0.5 Sec ON
0.5 Sec OFF
Battery
Disconnected/Faulty
This product contains a light source of energy efciency Class G.
EMERGENCY FITTINGS ONLY. EARTH CONNECTION REQUIRED.
L - LIVE (SW) = Brown
N - NEUTRAL = Blue
L1 - PERMANENT LIVE (PL) = Black
- EARTH = Green/Yellow
L (mm)
L (mm)
W (mm)
W (mm)
H (mm)H (mm)