M-system Kse-1 User manual

KSE-

❑

P. 1 / 3 EM-3609-A Rev.1

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

package you received as below.

If you have any problems or questions with the product,

please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

Signal conditioner (body + base socket + input resistor)

(1)

Input resistor is provided only with current input type.

■ MODEL NO.

Check that model No. described on specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, installation, connection and basic mainte-

nance procedures.

COMPONENT IDENTIFICATION

■ FRONT PANEL CONFIGURATION

INSTRUCTION MANUAL

MODEL KSE-❑1

DC ALARM

(dial adjustment; single trip)

Input Resistor

INSTALLATION

Detach the yellow clamps lo-

cated at the top and bottom of

theunitforseparatingthebody

from the base socket.

■ DIN RAIL MOUNTING

Set the base socket so that its

DIN rail adaptor is at the bot-

tom. Position the upper hook

at the rear side of base socket

on the DIN rail and push in the

lower. When removing the

socket, push down the DIN rail

adaptorutilizingascrewdriver

(–) and pull.

■ WALL MOUNTING

Refer to the drawings in the following page.

TERMINAL CONNECTIONS

Connect the unit as in the diagram in the following page or

refer to the connection diagram label on top of the unit.

When an input resistor is provided with the module, attach

it together with input wiring to the input screw terminals.

100

KSE

Model

-UNIT

Connection Diagram

Label Base Socket

Body

Specification

Label

Hi Monitor LED

Hi Setpoint Adj. Dial

100

Clamp

(top & bottom)

DIN Rail

35mm wide

Spring Loaded

DIN Rail Adaptor

Shape and size of the base socket

are slightly different with various

socket types.

KSE-

❑

P. 2 / 3 EM-3609-A Rev.1

–

INPUT 3

*Input shunt resistor attached for current input.

VPOWER

COM

HI OUTPUT

DRAWINGS mm (inch)

■DIMENSIONS

3456

2187

80 (3.15)

50 (1.97)

[3.3 (.13)]

80 (3.15)

(.79)

35.4 (1.39)

40 (1.57)

50 (1.97)

7.8 (.31)

CLAMP

(top & bottom)

DIN RAIL

35mm wide

2–4.5 (.18) dia.

MTG HOLE

15 (.59) deep

8–M3.5

SCREW

•When mounting, no extra space is needed between units.

116 (4.57)

136 (5.35)

■CONNECTION DIAGRAM ■TERMINAL ASSIGNMENT

2187

12 (.47)

INPUT RESISTOR

(model: REM)

Input shunt resistor attached

for current input.

KSE-

❑

P. 3 / 3 EM-3609-A Rev.1

CHECKING

1) Terminal wiring: Check that all cables are correctly

connected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal 7

–8 with a multimeter.

3) Input: Check that the input signal is within 0 –100% of

the full-scale.

4) Output load: Check that the output load is 380V AC/

100VA or 125V DC/30W at the maximum (≤0.5A for CE

marking). Foruse with inductive load,external protection

is recommended.

ALARM RELAY OPERATIONS

•Trip operation in power failure: terminals 5 –6 turn ON.

ADJUSTMENT PROCEDURE

■ HOW TO ADJUST ALARM SETPOINTS

Use a signal source and measuring instruments of sufficient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) Turn the front dial to an approximate position for the

setpoint.

2) Vary simulated input signal around the setpoint and

confirm relay operation and set.

POINTS OF CAUTION

■ CONFORMITY WITH CE/LVD DIRECTIVE

•This equipment is suitable for use in Pollution Degree 2

environment and in Installation Category II, with the maxi-

mum operating voltage 300V.

A basic insulation is maintained. Prior to installation, check

that the insulation class of this unit satisfies the system

requirements.

•The equipment must be mounted inside a panel.

•The equipment must be installed such that appropriate

clearance and creepage distances are maintained to conform

to CE requirements. Failure to observe these requirements

may invalidate the CE conformance.

■ POWER INPUT RATINGS

•Power input ratings are specified by the model number

suffix code. Check the power input voltage for the unit on the

specification label.

AC power: Suffix code K3 : 90 –132V

Suffix code L3 : 180 –264V

47 –66 Hz, approx. 3VA

■ GENERAL

•Before you remove the unit from its base socket or mount it,

turn off the power supply and input signal for safety.

■ ENVIRONMENT

•Indoor use

•When heavy dust or metal particles are present in the air,

install the unit inside proper housing and ventilate it.

•Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

•Environmental temperature must be within -5 to +55°C (23

to131°F)with relative humiditywithin 30 to90% RH inorder

to ensure adequate life span and operation.

■ WIRING

•Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

•Donot bindthese cables together with thosein whichnoises

are present. Do not install them in the same duct.

■ AND ....

•The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes.

Increasethe input signalfroma value lowerthan the setpoint

and check that the trip point remains within the accuracy

described in the data sheet.

When the trip points are out of tolerance, contact M-System’s

Sales Office or local representatives.

050100

Input

(%) ▲

Setpoint

Hi Output

(5–6)ON (1–2)ON

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.