Midea NTK15 User manual

PTC CERAMIC FAN HEATER
Model: NTK15
Instruction Manual
(Please read it carefully before use and save these
important instructions)
FEATURE
SPECIFICATION
IMPORTANT SAFEGUARDS
When using any electrical appliance, basic safety precautions should
always be followed, including the following:
1. Safety
PTC heating element works with a
Temperature around 200℃, no danger of
causing flames even if the unit falls on a
flammable surface, such as carpet, paper or
quilt. Automatic cut off the power when
raved about.
2. Energy saving
High efficiency, superior heat distribution
Achieved by heating 99% of air intake that
creates up to 5200 BTU of useable heat.
Instant heat, no need to wait and no need
to waste.
Substantially reduces your heating bills.
3. Portability
Compact size, light weight, convenient for
every locations where additional heat is
required.
4. Quality
Turbo fan motor ultra quiet in operation.
Power switch with inrush current protective
device guarantees 10,000 on/off cycles
without Malfunction.
Washable/replaceable air intake filter also
serves as air cleaner.
Model
NTK15
Voltage
230V~
Frequency
50Hz
Power consumption
1500W

1. To ensure familiarity with the controls, safety features, and
operation of your heater. Read all instructions before using.
2. To reduce hazard of injury due to electric shock.
2.1 Danger of shock exists even when the appliance is switched off.
ALWAYS unplug when not in use.
2.2 A heater should never be used under conditions where it may
be immersed, or come in contact with water. Similarly do not
plug in your heater if its surfaces are damp.
2.3 Do not insert foreign objects through the intake or discharge
grilles.
2.4 Do not operate the heater if the cord was damaged in any
manne r. Return it to an Authorized Service facility for inspection,
repairing and testing.
2.5 Close supervision is required when any appliance is used by or
near children.
2.6 Shut the power off before cleaning.
2.7 Unplug by grasping plug and pulling it from the outlet. NEVER
YANK ON CORD.
2. 8 When storing your heater, keep it in a cool, dry place.
2. 9 An electrical supply of 230 volts AC only, 50Hz is required.
Make sure that the plug is fitted in a suitable electrical supply
socket. Never use with an extension cord if the plug cannot be
fully inserted. Do not attempt to defeat this safety feature.
3. To reduce hazard of injury or property damage due to heat, fire,
or explosion:
3.1 Position your heater away from furniture or loose hanging
materials. Do not drape clothing or towels, etc. over the
heater to dry.
3.2 Keep the rear grille out from walls or drapes so as not to block
the air intake.
3.3 Use of an extension cord is not recommended. However, if it is
absolutely necessary ensure the cord is short as possible (long
cords coiled up can overheat, as well as cause tripping accidents)
and NOT USED TO SUPPLY POWER TO MORE THAN ONE
APPLIANCE AT A TIME.
3.4 Do not use in the presence of explosive or flammable vapors.
3.5 Do not run in locations when the heater will be left unattended
for long periods of time. (for example gseveral weeks in an
unoccupied summer cottage).
3.6 Use the heater on flat, dry surfaces only.
3.7 LOOSE CONNECTIONS BETWEEN THE HEATER PLUG AND THE
ELECTRICAL OUTLET MAY CAUSE THE PLUG TO OVERHEAT.
REPLACE ANY WORN ELECTRICAL RECEPTACLES PROMPTLY.
3.8 Use on 230-volt 50Hz AC power supply.
3.9 ENSURE NO OTHER APPLIANCES ARE PLUGGED INTO THE SAME
CIRCUIT AS YOUR HEATER. A CIRCUIT OVERLOAD COULD
OCCUR, RESULTING IN DIMMED LIGHTS, BLOWN FUSES,
TRIPPED CIRCUIT BREAKERS, OR FIRE HAZARD.
3.10 Route the cord so that it will not be walked on, or pinched by
furniture.
3.11 This product is intended for normal household use only.
4. AIR FILTER MUST BE USED.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
1. Plug into any 230V, 50HZ, and AC source. (See important
safeguards section 3.3 regarding use of extension cords).
2. Your heater is equipped with a 4-position control switch.
SYMBOL
FUNCTION
OFF
SHUT OFF POWER
LOW
APPROX—1000 WATTS
HIGH
APPROX—1500 WATTS
3. Set the control switch to maximum (HIGH) for fast warm up of a
room. Once the room is comfortable, select a lower setting to
reduce electrical consumption and to prevent the room from

becoming too warm.
4. Adjust the thermostat to maximum and select the desired power
setting. Once the room is comfortable, rotate the thermostat
counterclockwise, until the heater shuts off. The thermostat will
now maintain the temperature by cycling the heater on or off.
During particularly cold weather, the low power setting may be
insufficient to satisfy the thermostat. Select a higher setting for
these periods.
5. Use the oscillation function with the switch on.
REMEMBER: Portable electric heaters are designed for spot heating,
or as a supplementary heat source. They are not intended to be
main sources of heat during the normal heating season.
CAUTION: TO PREVENT ELECTRIC SHOCK. MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
NOTE: There may be trace of smoke or odor when unit is first
operated. Do not be alarmed, this indicates that a drop of oil fell on
the heating coil during the manufacturing process. It will quickly
evaporate, and should not re-occur.
PILOT LIGHT
The heater fan is equipped with a pilot light that glows whenever
the heater is plugged in and turned on. It will shut off if the
thermostat has cycled the fan and heating elements off. This
feature is to prevent you from being unaware that the heater is
operating and maintaining the temperature of the room. When you
do not wish the heater to control the room temperature, turn the
control switch to (OFF) and remove the plug from the electrical
outlet.
HOW TO CLEAN YOUR CERAMIC HEATER
A) Before any cleaning, make sure that
1. The Power Switch is set to OFF position.
2. Disconnect power supply at source by removing plug from power
outlet.
B) Regular Cleaning
1. To clean the enclosure, use a clean, soft and lightly wet cloth to
gently wipe off the dirt from the surface of unit. Be sure not to
wet the Ceramic Heating Element and the switches. Allow the
unit to dry completely before using it.
2. Do not use cleaning liquid or other chemicals to spray on the
unit.
3. After using the unit for a period of time, dust and other particles
in the air will collect on the air filter at the rear of the unit. Take
out the filter cover, remove the filter and rinse out in warm
water, allowed to dry completely. and reinstalled.
Air filter should be cleaned regularly.
4. Always tighten rear grill. Best is to use vacuum cleaner.
HOW TO STORE YOUR CERAMIC HEATER
1. Perform the cleaning Procedures described in How to clean
your ceramic heater.
2. Wipe all parts to dry.
3. Pack the heater in a plastic bag and store it in a dry place.