Mingda Magician X2 User manual

Instructions for quick assembly
V1.1
Magician X2

CONTENTS
Accessories
Assemble
Auto-leveling
Preheat
Insert the Filament
Printing
Z-offset adjust
Software Instructions
----------------------------------------------------------- 01
------------------------------------------------------------ 02
------------------------------------------------------- 06
--------------------------------------------------------------- 07
----------------------------------------------- 08
----------------------------------------------------------------- 09
----------------------------------------------- 11
------------------------------------------------------- 10

Accessories
01
Toolkit
The Main Chassis
Gantry
21 Filament 43
User manual Filament holder
Power cable
SD card Wrench
56 7 8Allen wrench
M4*20 (4pcs)
M5*25 (2pcs)
Nozzle
910 11 Teflon tube
12 13
M3*8 (2pcs)
Extruder
M4*10 (2pcs)

Assemble
Step 1 Install the gantry
Note: To avoid bending the lead screw
and effect the printing model, don't touch
or twist the lead screw when take out the
gantry from the package.
02
M5*25 (2pcs)
Note: The power supply has been
adjusted according to the local voltage.
If you need to adjust the voltage, please
follow the picture to operate it.

Step 2 Install the fixing plate screw
Step 3 Install the Filament Holder
03
M4*20(4pcs)
The filament holder can be installed left and right

04
Step 4 Connect Cable
Hotbed cable Z Motor 1 cable
Note: If you find there is a little shaking on extruder,bed or X-axis, don't worry, this is caused by long-term
transportation. Please refer to the adjustment video link in the SD card to adjust, it is helpful.
M3*8(2pcs)
Z Motor 2 cable Arranging Wire

Step 5 Install the Extruder
1.Push the extruder parallel into the
support, make sure the screw holes
on the top of the extruder are
aligned with the screw holes on the
support.
2.Use M4*10 screws to fix the
extruder on the support.
3.Connect the ribbon cable to the
port on the right side of the
extruder.
M4*10(2pcs)
05

06
Auto-leveling
Plug in the cable and turn on the
power
The printer will start auto-leveling after
preheat.
Click “Leveling” on main interface
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.

07
Preheat
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.
Click “preheat” on the main
interface
According to your filament, select
appropriate settings

08
Insert the filament
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.
In order to feed filament smoothly,
Please keep the end of the filament
at 90°.
Insert SD card
Click “load” to feed the
filament until the filament is
out of nozzle.

Printing
09
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.
Select a gcode file to print

10
Z-offset adjust
When you start your first printing,adjust the Babystep value according to the adhesion of the filament and the glass
platform. Click “Save” to save your setting, and you don’t need to adjust the value again next time.
[Note: Z-off set use for the first layer only]
If the distance between the nozzle
and the platform is too high, the
filament will not easy to stick to
the platform. Should click
"Decrease" until the distance is
proper.
Keep the distance between the
nozzle and the hot bed at 0.1mm,
the filament will stick to the hot bed
evenly
If the distance between the nozzle
and the platform is too low, the
filament will be not easy to feed out
smoothly . Should click "Increase"
until the distance is proper.

11
Install CURA
1. Double click Cura_xx.xx.exe to install
2. Install the software by default as follows.
Magician X2 works with a variety of slicing software, such as Cura, Simplify 3D, Repetier-Host, and more. We will introduce CURA_xx.xx in
detail, and you will learn how to set the slicing parameters, which will help you become more familiar with the slicing software and print
your first model successfully.
First, you can find the CURA_xx.xx from the SD card, and install it on your computer.
Step 1 Add Printer
Software Instructions

12
Click Add printer Choose Custom[Custom FFF printer ], insert Printer
name for example Magician X2,and Click Add
Insert print size, X230 Y230 Z260, select Heated bed Click Extruder 1, nozzle size 0.4mm, Compatible
material diameter 1.75mm, Click next

13
Step 2 Import Configuration file
Click Preferences, Configure Cura…
Click Profiles, Import Choose PLA+.curaprofile in SD card

14
After Import the profile, you will see it below,
choose PLA+, and click Activate
On the right side you can see PLA+ active
Click here, you can check all the parameter, when you move mouse
on it will show the explanation to help you under more clearly Click load button you can load a stl file, you can move,
rotate, and Zoom the model. Click Slice button.
Step 3 Slicing

15
After slice completed, you can see the time and weight of
material that the printing will take;
We suggest you click PREVIEW to check, you can choose
line Type and Drag the slider on the right side to see the
printing process clearly. After that , you can save it in your
SD card to print it out by the printer.

Shenzhen MINGDA Technology Co.,LTD
Email: [email protected]
www.3dmingda.cc
Official websiteFacebook PageYoutube Channel
For detailed warranty policy, please visit
http://www.3dmingda.cc/single/request_after_sales_service.html
For support ,please visit our Youtube Channel
https://www.youtube.com/channel/UC6PO64H7CfQtBy4H-fSRM4A?view_as=subscriber
Or you can visit our Facebook group at
https://www.facebook.com/groups/1018823731846578
Support request