Mocka Sadie User manual

*We recommend using a Flathead screwdriver to
tighten all locking nuts 100% before first use.
Please clear any loose wood from the locking nut
holes before inserting the nut to ensure it locks 100%.
WARNING: Any furniture that is not anchored to a
wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on
the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is
anchored to a wall. We supply a free safety wall
anchor with all furniture sold and we recommend
these are used to prevent your product tipping. The
fixing device provided should fit most wall types, but
please note that different wall materials may require
different fixing devices from those supplied.
Phillips & Flathead screwdriver required
ABCE
Hardware Supplied
x12
bolt
x25
locking
nut x 25
plastic
glide x4
Wall Mount
x2
washer
Z
wall
screw
Y
wall
anchor
x1
X
safety
strap x1
W
V
screw
x1
x1
Sadie Console Table
1
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
D
long
screw x6
dowel

12
Insert 10x bolts (A) and 8x dowels (C) into the panel [1]. Insert 7x bolts
(A) to the panel [5]. Tighten with a screwdriver.
Insert 8x bolts (A) into the panels [2], [3] and [4]. Tighten with a screwdriver.
1
3
A
A
A
AA
A
CC
CC
Sadie Console Table
2
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
Assembly Instructions
A
A
CC
A
A
CC
A
A
2
A
A
AA
A
A
AA
A
A
X 2
4
5
A

34
Attach panel [8] to panels [6] and [7] with 4x dowels (C) and secure
with 4x long screws (D).Tighten with a screwdriver.
Attach panel [9] to panels [2] and [3] with 4x locking nuts (B).
Tighten with a screwdriver.
Sadie Console Table
3
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
Assembly Instructions
8
D
D
D
D
C
C
C
B
B
B
B
6
7
9
2
3

56
Attach the unit to panel [1] with 6x locking nuts (B). Tighten with
a screwdriver.
Attach panels [6] and [7] to panel [1] with 4x locking nuts (B),attach
panels [6] and [7] to panel [9] with 2x screws (D). Tighten with a
screwdriver.
Sadie Console Table
Assembly Instructions
4
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
B
B
BB
B
B
B
B
9
2
3
1
1
6
7
D
9
D
D

78
Attach panels [4] to the unit with 4x locking nuts (B) as shown.
Tighten with a screwdriver.
Attach panel [9] to the unit with 7x locking nuts (B) as shown.Tighten
with a screwdriver. Attach 4x plastic glides (E) with a hammer to the
panels [2] and [3] as shown.
Sadie Console Table
Assembly Instructions
5
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
B
B
B
B
B
B
BB
B
B
B
6
7
2
3
4
4
2
3
7
6
8
9
E
E
E
E

910
Attach 1x safety strap (V) and 1x washer (Z) to panel [1] and secure
with 1x screw (W). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (V). Fasten to the
wall using 1x washer (Z), 1x wall plug (X) and 1x screw (Y). Ensure unit
is balanced and steady before use. You’re done, enjoy!
Sadie Console Table
Assembly Instructions
6
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
X
Y
Z
XY
Z
V
W
Z
V
Z
W
1
Wall Strap