molex 64000-0041 User manual

64000-0041 Manual Press
Doc. No. 64000-0041 Release Date: 09/24/02 UNCONTROLLED COPY Page 1 of 3
Revision: A Revision Date:09/24/02
Figure 3
RIBS
HOUSING ASSY
LOCKING
LATCHES
LOCKING
TABS
COVER ASSY
Figure 2
WIRE LOCAT0R
S
L
O
T
S
STRAIN RELIEF RIB
COVER ASSEMBLY
(BOTTOM FACING
UPWARD)
CABLE
JACKET
Operating Instruction Sheet
For 64000-0041 (Manual Press)
For SC Power Connector
Product No. 19403-0011
FEATURES
• Ratchet mechanism to insure full stroke.
• Adjustable termination height.
• Reversible for right or left hand operation.
• Dedicated tooling for quality assembly.
SCOPE
Self-Contained Power Connector Assembly for 14 AWG stranded wire. This connector is designed exclusively for Coleman
Cable E54864-H SEOPRENE 105 14 AWG 3/C SEOOW (UL) 600 V. –50°C to 105°C CSA LL39753-H STOOW (TPE).
OPERATION
1. Strip cable jacket and pre-form the wires as shown in Figure 1.
2. Position the clear cover (bottom facing upward) as shown in Figure 2.
3. Position wires into locator slots. Be certain to place black wire in slot marked BLK, green wire in slot marked GRD, and the white
wire in the third slot. Upon final positioning of all wires, be certain the end of the cable jacket is a minimum of .06” past the
second strain relief rib as shown in Figure 2.
CABLE JACKET
WHITE WIRE Figure 1
GREEN WIRE
1.00” BLACK WIRE
1.00”
Figure 4

64000-0041 Manual Press
Doc. No. 64000-0041 Release Date: 09/24/02 UNCONTROLLED COPY Page 2 of 3
Revision: A Revision Date:09/24/02
4. Position the housing assembly over the cover with the ribs
in the housing aligned between the latches as shown in
Figure 3. Push the two halves together until the locking
tabs engage as shown in Figure 4.
5. Place the connector assembly on the anvil. Position the
connector mounting holes onto the locator pins as shown
in Figure 5.
6. With connector in position as shown in Figure 6, pull the
ram handle from the full up position to the full down
position and return.
7. Remove terminated connector assembly by lifting straight
up to disengage connector from locator pins.
Note: Also see Document No. 11-32-8186 for operation and maintenance for Part No. 11-31-6356 (AM-60026) Manual
Assembly Press.
Molex Application Tooling Group
1150 E. Diehl Road
Naperville, IL 60563
[phone]; FAX [phone]
SC POWER
CONNECTOR LOCAT0R
PINS
PUSHER
Figure 5
MOUNTING
HOLES
ANVIL
MANUAL
PRESS
SC POWER
CONNECTOR
Figure 6

64000-0041 Manual Press
Doc. No. 64000-0041 Release Date: 09/24/02 UNCONTROLLED COPY Page 3 of 3
Revision: A Revision Date:09/24/02
PARTS LIST
*UFN 0SEFS/P &OHJOFFSJOH/P %FTDSJQUJPO 25: /PUFT1BSU
  .BOVBM1SFTTXJUI5PPMJOH 3&'
'JH
1 64000-0043 64000-0043 Anvil- 1

2 64000-0044 64000-0044 Pusher 1

3 11-31-6356 AM60026-50 Manual Assembly Press (Press Only) 1
4 11-31-7151 AM60037-5 Latch 1

5 11-31-7152 AM60037-6 Latch spring 1

6 11-32-6818 AM63240Q01 Adapter Body 1

7 N/A N/A #8-32 by 5/8”Lg. SHCS 3

8 N/A N/A M3 by 6.0mm Lg. SHCS 1

9 N/A N/A 1/8 by 3/4”Lg Dowel Pin 2

10 N/A N/A 1.5 by 6.0mm Lg. Roll Pin 1

64000-0045 64000-0045 Tool Kit (All Items except Item 3) 0
** The following purchased parts are available from an Industrial supply company such as MSC 1-800-645-7270.
Figure 7
5
7
8 4
9
6
3
(2)
(2)
2
1
7
10