Motorline professional TELICA Use and care manual

V3.2
REV. 05/2020
TELICA EN
USER’S AND INSTALLER’S MANUAL

A B
1B
4A
4B
5A
5A
10A
9B
8A
8B
11
10B
8A
9A
12
4B
5B
5B
6A
6A
6B
7
ENEN
INSIDE THE PACKAGE
DIMENSIONS
EMERGENCY UNLOCK
INSTRUCTIONS FOR FINAL CONSUMERS
MAINTENANCE
V MOTOR
INSTRUCTIONS FOR SPECIALIZED INSTALLERS
V MOTOR
TECHNICAL SPECIFICATIONS
INSTALLATION MEASURES
SUPPORTS INSTALLATION
. SAFETY INSTRUCTIONS
. THE PACKAGE
. OPERATOR
. INSTALLATION
. TROUBLESHOOTING
. MAINTENANCE
. MOTOR CONNECTIONS
. CONTENT . SAFETY INSTRUCTIONS
INDEX
AUTOMATISM INSTALLATION
ARMS INSTALLATION
MICROS ADJUSTMENT
INSTALLATION MAP
V MOTOR
V MOTOR
. COMPONENTS TEST
EXTERNAL UNLOCK
. CONNECTION SCHEME
V MOTOR
V MOTOR
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where they
purchased this product or the National Environment Agency
for details on where and how they can take these items
for environmentally safe recycling. Business users should
contact their vendor and check the terms and conditions
of the purchase agreement. This product and its electronic
accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.
ATTENTION:

A B
ENEN
. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•Thismanual isintended firstly forspecializedtechnicians, anddoes not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical,sensorialormentalcapacitiesarelower,orbypersonswithout
any knowledge of the product, provided that these are supervision
and instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The centralmust beinstalled ona safe placeof any fluid(rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.
•Attach the permanent label for the manual release as close as possible

A B
ENEN
. SAFETY INSTRUCTIONS
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information
This product was designed and manufactured by Motorline Electrocelos SA,
located in Travessa do Sobreiro nº29, 4755-474 Rio Côvo (Santa Eugénia)
Barcelos, Portugal.

A B
155mm
240mm
220mm
265mm
525mm
415mm
ENEN
. THE PACKAGE . OPERATOR
INSIDE THE PACKAGE DIMENSIONS
TECHNICAL SPECIFICATIONS
Components on the 2 motor's package:
01 • 02 articulated motors
02a • 01 articulated right arm
02b • 01 articulated left arm
03 • 02 4 channels remote controls
04 • 02 frontal supports
05 • 02 motor supports
06 • 02 unlock keys
07 • 01 photocells set
08 • 01 user manual
Kit components:
The dimensions of the TELICA automation are the following:
Kit package:
24V 230V
• Power supply 24Vdc 230Vac
• Power 220W 380W
• Force 200 Nm
• Working frequence Intensive Use 50 %
• Capacitor -12,5 F
• Protection grade IP54
• Noise LpA <= 50dB (A)
• Thermal protection - 120°C
• Operating temperature -25°C to 55°C
• RPM 1,30 RPM 1,10 RPM
Fig. 1
Fig. 4
Fig. 2
Fig. 3
07•03•
06•
04•
05•02b•
08•
01•
02a•
Components on the 1 motor's package:
01 • 01 articulated motor
02a • 01 articulated direito/esquerdo arm
03 • 02 4 channels remote controls
04 • 01 frontal support
05 • 01 motor's support
06 • 01 unlock key
07 • 01 photocells set
08 • 01 user manual
This automation is suitable for leaves up to 2.5 meters wide. For leaves with a width higher
than 2,50 meters, we recommend the use of an electric lock.

A B
1
2
3
B
A
AB
CDE
450mm
15mm
CSV100CSV100CSV100
ENEN
. INSTALLATION
EMERGENCY UNLOCK INSTALLATION MEASURES
. INSTALLATION
•Thetable belowindicates
the measure which quota
Bshould have in function
of the quota Ameasure.
SUPPORTS INSTALLATION
1• Drill holes for M8 screw anchors.
• You must use appropriate anchorages for the type
of surface where the automation will be installed.
2• Place the anchors in the holes, press the pla-
te against the wall and fix it with the appropriate
screws.
3 • Attach the front support to the door leaf,
following the dimensions of Fig. 10. • 450mm from
the door hinge and 15mm below the motor support.
Use M8 bolts for fixing the supports.
Fig.8
Fig. 9
Fig. 10
The emergency unlock should only be used in case of emergency, electrical failure or
malfunction.
Fig. 5
To unlock...
insert the unlock key into the automation front hole
and turn it on clockwise 4-5 times until you feel a
limit.
To lock...
Rode a chave no sentido contrário até sentir um ob-
stáculo.
EXTERNAL UNLOCK
Fig. 6 Fig. 7
The kit exemplified below is not included in the TELICA Kit.
1• Pass the cable into the TELICA through the cable
gland.
2• Place the cable sleeve in the indicated location
and fix it with a washer and a screw.
3• Pass the steel cable through the hole in the trig-
ger and fix it with a end-fixing. Cut the excess.
The cable can then be connected to a security box
as in fig. 7 to allow external unlocking.
QUOTA A QUOTA B
máx. 350 mm 1 a 1 mm
300 mm 1 a  mm
250 mm 11 a  mm
200 mm 1 a  mm
10 mm 1 a  mm
mín. 1 mm 1 a  mm
QUOTA A • Vertical distance between the center of the hinge and the center of the motor shaft.
QUOTA B • Horizontal distance between the center of the hinge and the center of the motor shaft.
Security
Box

A B
A
C
B
A A
D D
E E
G G
M M
SIGNED NAME
B
A
C
1 2 3
≈3cm
ENEN
. INSTALLATION
AUTOMATISM INSTALLATION MICROS ADJUSTMENT
. INSTALLATION
1• Place the motor on the support plate and
fix it with supplied M8 screws.
The arms are supplied already assembled.
• If you install only one motor and the arm is not in
the correct position, you can easily change the direc-
tion following the indications in the picture Fig. 13.
1• Mount the square hole in the motor's output shaft, and tighten with provided washer and M10x20
screw. 2• Place the other extremity of the arm under the gate support, and secure with screw, bushing,
washer, and female.
1• Unlock the automation and open the door leaf to the desired position.
2• Loosen (A) the opening ring screw, and turn it (B) until you hear a *click* of the micro switch.
3• Tighten the screw (C) of the ring to lock it in this position.
ARMS INSTALLATION
Remove the automation's
cover. To do this, loosen the
two front screws, slightly tilt
the cover back and pull up.
After the installation is complete, make all the electrical connections and replace the cover.
Fig. 11
Fig. 14
Fig. 12
Fig. 13
Fig. 16 Fig. 17 Fig. 18
4• Close the door leaf, loosen (A) and turn (B) the
closing ring until it makes a *click* into the corres-
ponding micro. Retighten (C) the ring screw.
5• Manually test the opening and closing of the gate
to ensure that the micro switches are activated in
the correct point. 6• When the micros are tuned, re-
-lock the automation.
Fig. 19 Fig. 20 Fig. 21 Fig. 22
Fig. 15

EN
. INSTALLATION
INSTALLATION MAP
INTERIOR
PHOTOCELLS
EXTERIOR
PHOTOCELLS
EXTERIOR
PHOTOCELLS
KEY
SELECTOR
MOTOR WARNING
LAMP
ANTENNA
JUNCTION BOX
LEGEND: Connection cables
It is important to use mechanical stoppers in the opening and closing position of the gate.
If not respected, components of the automation may suffer efforts for which they were not
prepared, and as a result will be damaged.
It is important to use junction boxes for connections between motors, components and
control unit. All cables must enter and exit on the bottom of the junction and control board
box.

GATE STOPPER
Fig. 23

A B
V
PU
SERR.
L N
LAMP
230V
MOTORE 1
AP COM CH
MOTORE 2
AP COM CH
1 1 12 2 23 3 34 45
5
6 7 8 9 10
1 12 23 4 5 6 7 8 9 10 11
MOT.2 SERR.
+ -
+ V
CN1 CN2
MOT.1
LAMP
+ -
BAT
+12V-
12/20V S.P.
+
ENEN
. COMPONENTS TEST
V MOTOR
AUTOMATISM
8μF (230V) / 20μF (110V)
Capacitor
1
2
3
2
COM 1
COM 2
COM
Ground Wire
Phase 2
Phase 1
Open
Close
Motor
Power Supply 1
Power Supply 2
Fig. 23
To detect if the malfunction is on the control board or on the motor is, sometimes, necessary to perform
tests with connection directly to a 230Vac power supply.
For this, it is necessary to interpose a capacitor on the connection in order to the automatism to work
(check the type of capacitor to be used in the product manual).
The diagram below, shows how to make that connection and how to merge the different components
wires.
All tests must be performed by qualified personnel due to serious danger associated
with the misuse of electrical systems!
NOTES:
• To perform the tests, there is no need to remove the automatism from the place it is instal-
led, because in this way, it is possible to understand if the automatism can function properly
connected directly to the current.
• You should use a new capacitor during this test to ensure that the problem does not lie on it.
1• Connect the power wires to the terminal, as shown below.
2• Connect the automatism wires in the terminal, interposing a capacitor in the
opening and closing wires.
3• Once these connections are completed, connect to a 230Vac power outlet, depending on the motor /
control board in test.
V MOTOR
. CONNECTION SCHEME
MOTOR WIRES |CONNECTIONS
Connections should be made as shown above, connecting the  motor wires to the appropriate inputs
of the central and capacitor.
NOTE: The white motor wires are connected directly to the capacitor wires!
V MOTOR
Yellow/Green
Black
Blue
Brown
Black
Black
Wires color Motor  wires Motor  wires
Ground Wire
MOTOR-AP
MOTOR-COM
MOTOR-CH
Capacitor
Capacitor
Ground Wire
MOTOR-AP
MOTOR-COM
MOTOR-CH
Capacitor
Capacitor
• These connections correspond to an installation with an opening to the interior. If the au-
tomation is installed with an opening towards the outside of the gate, you must swap the AP
wire with the CH wire on the motor 1 and 2.
• If the motors work towards the opposite direction, swap AP with CH.

A B
ENEN
. COMPONENTS TEST
V MOTOR
AUTOMATISM
Motor rotates to
one direction
(eg: right)
24Vac Battery
Motor’s wires
24Vac Battery 24Vac Battery
Motor rotates in
the opposite
direction
(eg: left)
To detect which are the components with problems in a 24Vdc TELICA automatism instalation, it's some-
times necessary to run a test directly to a external power supply (another 24Vdc battery).
The diagram below shows how to connect the motor to the battery.
All tests must be performed by qualified personnel due to serious danger associated
with the misuse of electrical systems!
NOTES:
• To make these tests it isn't necessary to remove it from the location where it is installed, be-
cause in this way, you can understand of the automatism works properly directly connected
to the external battery.
• Once you connect the wires to a battery 24V, the motor must work for one direction. To test
the opposite movement, change the position of the wires connected to the battery.
. MAINTENANCE
MAINTENANCE
Thesemaintenancemeasuresmustbeapplied everyyearinordertoinsureproperfunctioning
of the automated system.
• LUBRICATE PINS
Place a small amount of lubricant on the
holes that contains support pins.
• CHECK MOTOR SUPPORTS
Make sure that supports remain well fixed on the
pillars and gate to ensure proper functioning of
the equipment.

A B
ENEN
. TROUBLESHOOTING
INSTRUCTIONS FOR FINAL CONSUMERS INSTRUCTIONS FOR SPECIALIZED INSTALLERS
Anomaly Procedure Behavior Procedure II Discovering the origin of the problem
• Motor
doesn't work
at all
• Make sure you
have 230Vac/24Vdc
power in the
automation control
board and if it is
working properly.
• Still not working • Consult a qualified
MOTORLINE technician. 1 • Open control box and checkif it has 230Vac/24Vdc power supply; 2 • Check input fuses;
3 • Disconnect motor from control board and test it by connecting directly to power supply in order to find out if it has problems (see page 8B)
4 • If the motor work, the problem is on the control board. Pull it out and send it to our MOTORLINE technical services for diagnosis;
5 • If the motor doesn’t work, remove it from installation site and send to our MOTORLINE technical services for diagnosis.
• Motor
doesn’t move
but makes
noise
• Unlock motor and
move gate by
hand to check for
mechanical problems
on the gate.
Did you find
problems? • Consult an experienced gate expert.  • Check all motion axis and associated motion systems related with gate and operators (pins, hinges, etc.) to find out what is the problem.
• Gate moves
easily? • Consult a qualified MOTORLINE technician. 1 • Disconnect motor from control board and test it by connecting directly to power supply in order to find out if it has problems (see page 8B)  • If the motor work, the problem is on the control board. Pull it out and send it to our MOTORLINE technical services for diagnosis;
 • If the motor doesn’t work, remove it from installation site and send to our MOTORLINE technical services for diagnosis.
• Motor
opens but
doesn’t close
• Unlock motor and
move gate by hand to
closed position.
Lock motor(s) again
and turn off power
supply for 5 seconds.
Reconnect it and send
order to open gate
using transmitter.
• Gate opened but
didn’t close again. 1 • Check if there is any obstacle in front of the
photocells;
2 • Check if any of the control
devices (key selector, push
button, video intercom, etc.)
of the gate are jammed and
sending permanent signal to
control unit;
3 • Consult a qualified
MOTORLINE technician.
TAll MOTORLINE control boards have LEDs that easily allow to conclude which devices are with anomalies. All safety devices LEDs (DS) in normal
situations remain On. All "START" circuits LEDs in normal situations remain Off.
If LEDs devices are not all On, there is some security systems malfunction (photocells, safety edges), etc. If "START" circuits LEDs are turn On, there
is a control device sending permanent signal.
A) SECURITY SYSTEMS:
 •Close with a shunt all safety systems on the control board (check manual of the control board in question). If the automated system starts
working normally check for the problematic device.
 • Remove one shunt at a time until you find the malfunction device .
 • Replace it for a functional device and check if the operator works correctly with all the other devices. If you find another one defective, follow
the same steps until you find all the problems.
B) START SYSTEMS:
 • Disconnect all wires from START terminal input.
 • If the LED turned Off, try reconnecting one device at a time until you find the defective device.
NOTE:
If the procedures described in sections A) and B) don’t result, remove control board and send to our technical services for diagnosis.
• Motor
doesn’t make
complete
route
• Unlock motor and
move gate by
hand to check for
mechanical problems
on the gate.
• Encountered
problems? • Consult an experienced gate expert  • Check all motion axis and associated motion systems related with gate and operators (pins, hinges, etc.) to find out what is the problem.
• Gate moves
easily? • Consult a qualified MOTORLINE technician.  • Check if the limit microswitches are adjusted for the required course.  • Disconnect motor from control board and test it by connecting directly to power supply in order to find out if it has problems (see page 8B)
 • If the motor doesn’t work, remove it from installation site and send to our MOTORLINE technical services for diagnosis.
 • If motors work well and move gate at full force during the entire course, the problem is from controller. Set force using trimmer on the board.
Make a new working time programming , giving suffient time for opening and closing with appropriate force (see manual of the controller in
question).
NOTA:
Setting force of the controller should be sufficient to make the gate open and close without stopping, but should stop with a little effort from a
person. In case of safety systems failure, the gate shall never cause physical damaged to obstacles (vehicles, people, etc.).


L N
LAMP MOTORE 1
AP COM CH
MOTORE 2
AP COM CH VPUL
SERR. PED
PUL PED DS1 DS2
INB.CMD.AP
CODE
T.MOTOR
T. PAUSA
CODE PED
T.MOT.PED
T.RIT.ANT
PL
1 1 12 2 23 3 34 45 56 67 78 89 9 1110 10 12
L N
DS1 DS2
110V
110V
COM NC
CONTACT
~ ~
POWER
12V/24V
~ ~
POWER
12V/24V
~ ~
COM NC
CONTACT
POWER
12V/24V
~ ~
POWER
12V/24V
EN
. CONNECTION SCHEME
Exterior
Photocells*
Interior
Photocells*
• Motor 1 starts opening before Motor 2
• Motor 2 starts closing before Motor 1
• It must be applied an 8µ capacitor
in each motor, on the opening and
closing wires as explained above.
NOTE • If any one of the motors moves
in the wrong way, just switch the brown
and black cables of that motor to
change the direction.
Complete
Opening
(2 leaves)
Lock
Light Bulb
Antenna
- Force +
Earth wire
Black
Black
Earth wire
Blue
Blue
Brown
Brown
Pedestrian
Opening
(1 leaf)
Motor 1
Motor 2
Close the circuit
with bridge (shunt)
when the
photocells circuit
is not being used!
(9
∑
8 - 9
∑
10)
* For more
informations,
check the manual
of the photocells
to be installed .
V MOTOR


VR1
SEL
CN1 CN2
SET
1,6Ah
10Ah
F1
F2
PUL
1 2 3 4 5 6 7 9 10 118 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 188
PUD
VR1
T. RIT. ANTE T. PAUSE T. MOT. PED. T. M OT. CODE PED. CODE AUTO PGM TIPO MOTORE
RX
BL DS FA1 FC1 FA2 FC2
12/20V M O T.1 MOT.2 PUL PED BL DS FA1 FC1 FA2 FC2+V
B AT T
+12V-
LAMP
+ -
SERR.
+ -
L.SPIA
+12V-
S . P.
+
+12V-
POWER
12V/24V CONTACT
POWER
12V/24V
COM NC
POWER
12V/24V CONTACT
POWER
12V/24V
COM NC
POWER
12V/24V CONTACT
POWER
12V/24V
COM NC
POWER
12V/24V CONTACT
POWER
12V/24V
COM NC
POWER
12V/24V CONTACT
POWER
12V/24V
COM NC
FUSE
DS
FA1
FC1
FA2
FC2
230Vac: 2Ah 115Vac: 3Ah
N0 N0
EN
. CONNECTION SCHEME
Complete
opening
Partial
opening
Flashing
light
12/24VD
4W Máx.
Transformer:
230Vac or
110Vac
5 0/60Hz
120W Máx.
Solar Panel
Electric lock
12/24VDC 12W Máx.
Emergency
STOP button
CN2 (4)
Maximum output of 125mAh.
Sets of
photocells
(NC)
12Vdc
3W Máx.
Antenna
230Vac or 110Vac
Motor 2Motor 1
Set of
Photocells
FC1
Set of
Photocells
DS or FA1
Set of
Photocells
FA2
Motor 2Motor 1
Set of
Photocells
FC2
When the photocells circuits are not being used, you must close
them with a bridge (shunt) on the control board.
( 14
∑
11 - 14
∑
12 - 14
∑
13 - 14
∑
15 - 14
∑
16)
When the STOP button is not being used,you must close the hem
with a bridge (shunt) on the control board. (9
∑
10)
PHOTOCELLS DIAGRAM
Power Supply
V MOTOR