Motorline professional KVM105 Operation and installation manual

v5.1
REV. 07/2021
KVM105, KVM110, KVM115
KVM105, KVM110, KVM115
EN
INSTALLER AND USER’S MANUAL

1A 1B
1B
4A
4A
4A
4B
6A
5A
7A
7B
8A
ENEN
00. CONTENT
INDEX
KVM105, KVM110 AND KVM115
PACKAGE
TECHNICAL CHARACTERISTICS
MANUAL OPENING / CLOSING
. SAFETY INSTRUCTIONS
. AUTOMATISM
AUTOMATISM INSTALLATION
INSTALLATION GUIDE
FIX CONTROL PANEL ON THE WALL
ADJUSTMENT OF LIMIT SWITCHES
. INSTALLATION
. INSTALLATION MAP
MOTOR AND CONTROL PANEL DIMENSIONS
ATTENTION:
01. SAFETY INSTRUCTIONS
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where they
purchased this product or the National Environment Agency
for details on where and how they can take these items
for environmentally safe recycling. Business users should
contact their vendor and check the terms and conditions
of the purchase agreement. This product and its electronic
accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.

2A EN
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk causing
serious injuries.
•This manual is intended firstly for specialized technicians, and does not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Donotuse the product ifit is necessaryrepair or adjustmentisrequired.
•When performing maintenance, cleaning and replacement of parts, the
product must be disconnected from power supply. Also including any
operation that requires opening the product cover.
•The use,cleaningand maintenanceofthisproduct may becarried out by
any persons aged eight years old and over and persons whose physical,
sensorial or mental capacities are lower, or by persons without any
knowledge of the product, provided that these are supervision and
instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation of
the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points to
ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The central must be installed on a safe place of any fluid (rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the power
supply cable. Please note that all the cables must enter the central
from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.
01. SAFETY INSTRUCTIONS

3A EN
•Attach the permanent label for the manual release as close as possible
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
01. SAFETY INSTRUCTIONS
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information

4A 4B
•
•
•
•
•
• •
•
•
•
ENEN
KVM, KVM and KVM are spindle drive automatims for sectional industrial door automation,
with the possibility of horizontal or vertical application. The ease of installation,
configuration and maintenance make it ideal for all sectional doors.
The automatism release system allows the user to open
manually, in case of emergency and/or power cuts.
For that just have to pull the circular chain in one direction
or another to proceed to the
manual opening or closing as shown in the picture.
In the kit you will find the following components:
02. AUTOMATISM 02. AUTOMATISM
KVM105, KVM110 AND KVM115
KVM KVM KVM
• Lubricant Type Oil
• Noise <55dB
• Chain Type Standard chain
• Maximum limit of limit switches  motor's rotations
• Shaft Bore Diameter 25,4mm
• Working temperature -20~+45C
• IP IP54
• Power Supply V  Hz V  Hz
• Capacitor F F -
• Power W W W
• Force 70N 120N 200N
• Working frequency 25% 20%
• Thermal 120C
• Motor RPM 1400 RPM
• Reducer RPM 24 RPM
• Weight 20Kg 20,2Kg 20,7Kg
TECHNICAL CHARACTERISTICS
MANUAL OPENING / CLOSING
PACKAGE
01• 01 KVM Motor
02• 01 Control panel (with control board)
03• 01 Motor fixing plate
04• 01 Chain
05• 02 Protection ring
06• 04 Motor fixing screws
07• 01 Dowel
08• 01 Cable Entry Sleeves
09• 01 Release System
10• 01 Shaft Reducer

5A
aa’
b’
g
g
b’
b
b
c
EN
02. AUTOMATISM
MOTOR AND CONTROL PANEL DIMENSIONS
KVM105 KVM110 KVM115
• Motor Dimensions (a x b x c) xx xx xx
• Reducer Width (c') 110 110 110
• Total Motor Height (a) 400 450 450
• Control Panel Dimensions
(d xe xf) xx - -
• Motor Depth (b) 236 240 240
• Total Height of Electronic Panel
(a') 282 170 170
• Distance to the center of reducer
(b') 54 55 55
• Distance between center of
screws (g) 83 83 83

6A
2
3
5
41
1
2
3
4
5
30~100mm 30~100mm
350mm
EN
. INSTALLATION
ASSEMBLY THE SHAFT
Leave an excess of 350mm at the spring vain through the support. Insert a protection ring
on the vain.
FIT MOTOR
Place the motor on the shaft of 3-10 cm left over from both sides.
See detail A.
MARK THE HOLES
Place the plate on the motor without tighten completely.
Touch the plate on the wall and make markings.
DRILL THE HOLES
Remove the motor's plate and make the drills to fixate the motor.
ATTACH MOTOR
Fix the plate on the wall and then fix it in the motor.
Put the protection ring on the vain, touch it to the motor and and tighten.
AUTOMATISM INSTALLATION
• The gearmotor must be installed in a protected area of shocks.
• The fixation surface should be solid.
• Should be used accessories with capacity to fixing the engine to surface.
• Install suitable tubes for the passage of electrical cables, to ensure the complete
protection against mechanical damage.
• The door structure must be resistant enough, with efficient hinges.
• There should be no friction between fixed parts and moving parts.
DETAIL A

7A 7B
1
4
3
3
2
click
1
2
4
5
3
5
3
2
1
ENEN
. INSTALLATION . INSTALLATION
FIX CONTROL PANEL ON THE WALL ADJUSTMENT OF LIMIT SWITCHES


MARK THE HOLES
Make a wall mark to a distance of 1500mm from the floor.
Put the base of the board box in the marking. Marks the drilling locals.
DRILL THE HOLES
Then proceed to the drillings.
ATTACH CONTROL BOARD
Apply the bushings and fix the board on the wall.
CONNECT CONTROL BOARD
Insert the wires through inferior side of the board box. Put the box cover.
Close the cover and press the screws until the box is completely fixed.
Loose the screw A opening
micro (right ring) and
adjust the ring until you
hear the micro click. Turn
to tighten the screw.
Make sure the door is open and make sure
about which is the opening limit-switch.
General tuning is for full tuning, looping
tuning rings.
Fine tuning is in turn a detailed tuning on
the tuning ring to achieve the most accurate
tuning.
Make sure the door is closes and repeat the 2 and 3 processes (middle ring).
Use now screw Bto a more
precisely tuner of the limit-
switch, tuning the plastic
that active the micro.
On the last micro make an identical
tuning on the opening micro so that it can
be activated just before the opening finish.
Screw A correspondes to general tuning and B is the fine tuning screw.
Do not only use fine tuning if you want make a full adjustment, this may damage the
tuning rings.
If the motor operates in the opposite
direction, you must change the
connections that turn on the motor,
inside the industrial box.

8A EN
. INSTALLATION MAP
INSTALLATION GUIDE
1500mm
Control Panel
with control
board
KVM105 / KVM110 /
KVM115
Motor
You can install the engine horizontally or vertically, the procedure is the same.
See detail A.
DETAIL A