Motorline professional SUBWING 700 Use and care manual

V2.1
REV. 08/2022
SUBWING 700SUBWING 700
EN
USER’S AND INSTALLER’S MANUAL

A B
1B
4A
5A
5B
6A
6B
7A
7B
4A
A B
4B
4B
7A
ENEN
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX
CONNECTION SCHEME
INSTALLATION MAP
GATE LEAF OPENING ANGLE
BOX INSTALLATION
ASSEMBLING THE MOTOR AND LEVERS
MOUNTING THE MOTOR LEVER TO THE GATE
EMERGENCY RELEASE
. SAFETY INSTRUCTIONS
. AUTOMATION
. INSTALLATION
FINAL CONSUMERS AND SPECIALIZED INSTALLERS INSTRUCTIONS
. TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
DIMENSIONS
LIMIT SWITCHES ASSEMBLY (OPTIONAL)
ATTENTION:
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances
in electrical and electronic equipment and with Delegated
Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where
they purchased this product or the National Environment
Agency for details on where and how they can take these
items for environmentally safe recycling. Business users
should contact their vendor and check the terms and
conditions of the purchase agreement. This product and
its electronic accessories should not be mixed with other
commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.

A EN
01. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•This manual is intended firstly for specialized technicians, and does
not invalidate the user’s responsibility to read the “User Norms”
section in order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and
other mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical, sensorial or mental capacities are lower, or by persons
without any knowledge of the product, provided that these are
supervision and instructions given by persons with experienced in
terms of usage of the product in a safe manner and who understands
the risks and dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if
the necessary mechanical stops are in the appropriate places.
•Thecentralmustbeinstalledonasafeplaceofanyfluid(rain,moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.
•Attachthe permanentlabelfor themanualrelease as close as possible

A EN
01. SAFETY INSTRUCTIONS
•to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•If the system requires any repair or modification, unlock the
automatism, turn off the power and do not use it until all safety
conditions have been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in
in motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if
the product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information
MOTORLINE ELECTROCELOS SA.
Travessa do Sobreiro, nº29
4755-474 Rio Côvo (Santa Eugénia)
Barcelos, Portugal

A BA B
1
2
2
3
4
5
5
6
7
8
RG58/9
230V AC
119mm
329mm
227mm
141mm
140mm
198mm
146,5mm
11,5mm
230mm
375mm
320mm
65mm
165mm
Ø 65mm
ENEN
02. AUTOMATION 02. AUTOMATION
CONNECTION SCHEME TECHNICAL SPECIFICATIONS
1• Motor
2 • External photocell 3 • Flashing lamp 4 • Antenna 5 • Internal photocell 6 • Electronic control board 7 • Key selector 8 • Remote control
V V
• Max. weight of leaf Kg
• Max. width of leaf ,m
• Motors power supply V DC V AC
• Motor power W W
• Rotational speed  RPM  RPM
• Capacitor - ,F
• Mechanical unlock for emergency With key
• Operating temperature -C/C
• Weight Kg
• Protection class IP
• Opening time   sec
• Impulse force Nm
• Motor current consumption A ,A
INSTALLATION MAP
DIMENSIONS
x,mm (V DC)
x,mm (V DC)
x,mm
x
,mm
x,mm
x,mm
Power supply V
Photocell RX Photocell TX
x,mm

A BA B
72mm
375mm
320mm
C1
F 2
F 1
165mm
ENEN
BOX INSTALLATION
03. INSTALLATION
GATE LEAF OPENING ANGLE
03. INSTALLATION
Establish the required opening angle.
1• Create a hole (taking into account
the dimensions indicated in the
image) to contain the motor support
box (C1).
2• Insert the tube for water
drainage in the prepared hole (F1).
3• Insert the tube for the power
cable to pass into the hole (F2).
Note: while positioning the box,
keep in mind the minimum
distance there must be between
the pillar and the centre of rotation
of the gate hinge.
4 • Cement so that the box cannot
be moved, wait for it to dry and
then assemble the motor and
levers.
Distance between
Pillar and Hinge Axis
BOX
POSITION
BOX
POSITION


INSIDE VIEW
INSIDE VIEW
PILLAR
PILLAR

A BA B
L 1
L
ENEN
ASSEMBLING THE MOTOR AND LEVERS MOUNTING THE MOTOR LEVER TO THE GATE
03. INSTALLATION 03. INSTALLATION
1• Place the motor in the box and secure it with
the screws provided. Place and fix the cover with the screws provided.
Position the gate leaf and the lever (L) so
that they are perfectly aligned and fix them by
welding or another type of fixing.
2• Insert the ball on the box stud and apply the
gate anchor (L1).
3• Put the connection lever (L2) between the
levers (L3) and (L1).
BALL
welding
L
L
L
L

A BA B
L 1
V
C
ENEN
03. INSTALLATION
EMERGENCY RELEASE FINAL CONSUMERS AND SPECIALIZED INSTALLERS INSTRUCTIONS
Place the key (C) supplied, in the hole
(V), which is located in the lever L1 and
turn it.
Insert, regulate and block the mechanical limit switches in the desired position.
04. TROUBLESHOOTING
LIMIT SWITCHES ASSEMBLY (OPTIONAL)
Closing Opening
Problem Probable cause Solution
• With a remote control or key
selector, the gate does not
open or the motor does not
work
• There is no 230V power
supply • Check main switch
• Emergency STOP present
• Control selectors or remote
controls STOP. If you do not
use STOP, check the bridge at
the STOP contact input on the
control board
• Fuse blown • Replace with one of same
value
• Motor(s) power cable
disconnected or defective
• Connect the cable to
appropriate terminal or
replace
• There is an obstacle between
the photocells or they do not
work
• Check the connection, remove
any obstacle
• The gate does not open with
a remote control, but works
with the key selector
• The remote control has not
been memorised or the battery
is low
• Follow the remote control
recognition procedures on the
receiver or replace the battery
with a new one
• Gate starts to open/close, but
stops • The force of the motor(s) is insufficient
• Modify the value with the
FORCE button on the control
board
• One leaf opens and the other
closes • The connection is not correct
• Change the polarity of the
motor cable that is working in
the opposite direction to the
correct one