Motorline professional Gateway Control SLIDE 500 User manual

!
!
1!
!
!
!
!
SLIDE 500
Operating and installation instructions

!
!
2!
General safety instructions and checklist
This electric gate operator complies with European Directives: 89/336/EEC and 2006/95/CE and subsequent
amendments.
When installed correctly this electrically operated motor complies with all relevant safety standards.
Please ensure the operating manual is fully read and understood before installation and operation.
Installation should only be carried out by a competent and qualified person.
Always ensure that all people especially children, animals and objects are well away from the gate opening area
during the gates operation.
Keep remote control transmitters out of reach of children, to prevent unintentional operation.
Do not intentionally obstruct the gate/s in any way during operation.
Do not modify or attempt to modify any part of the gate motor or control system.
This gate motor should always be installed with safety in mind as prescribed by the standard EN12978. Safety
Photocells, safety edge or induction loops should be used correctly wherever possible.
In case of malfunction or power failure, this device is supplied with a manual release which is operated by a
manual key to release the motor.
Always ensure that the power supply is off before attempting installation or to alter any settings.
Only allow gate operation when in full view of the complete gate system.
Basic maintenance should be carried out regularly, such as to ensure safe working of the gate. Safety devices
should be checked on a monthly basis. The gate motor should be kept clean at all times.
The mechanical parts of the gate motor conform to standards EN12604 and EN12605.
It is the responsibility of the installer to ensure the safe working of the automated gate. The installation must
conform to standards EN12453 and EN12445. Test pressure settings and Safety Photocells conform to EN
12445.
The end user should be fully instructed in the safe working of the gate, and should be given all safety and
installation manuals.
All packaging material and unused equipment should be disposed of in the correct, environmentally friendly way.
Never install devices where a user can reach over or through an automated gate system. All external electrical
components (Photocells, keypads, flashing lights etc), must be connected in accordance to EN 60204-1 and
amendments made to point 5.2.2 of EN 12453.
The power supply, control panel and motor should be earthed properly. The mains power supply should be fit for
purpose and fitted with omnipolar switch with a contact opening distance of 3mm or more. A 6A thermal circuit
breaker is also recommended.
The motor is CE marked by Stateurop, the manufacturer. The automated gate system must be certified by the
installer as being compliant with the European Machinery Directive, and be given an appropriate CE certificate to
state that the gate and automation comply with current regulations for safety.
Gateway Control Ltd declines all responsibility for any consequences resulting from improper use or installation,
or failing to observe good technical practice.

!
!
3!
Description of maintenance
Maintenance
Schedule
Clean and check safety Photocells and functions
Monthly
Check free movement of gate manually
Monthly
Clean foliage or insects from gate or control box
Monthly
1. Description
The SLIDE 500 is an electro-mechanical sliding gate operator, designed to automate domestic sliding
gates up to a maximum 7 metres wide and up to 500Kg in weight.
The on board control panel is very versatile and has a number of safety functions as standard
The motor has opening and closing limit switches, and a solid manual release mechanism.
The operator is irreversible and locks mechanically in the open and closed position when not in use.

!
!
4!
2. Technical Specifications

!
!
5!
3. Packaging
1. Slide 500 motor x 1 5. Foundation Plate x 1
2. Left Limit Switch plate x 1 6. Expanding bolts –not supplied
3. Right Limit switch plate x 1 7. Foundation plate nuts & bolts x 4
4. M6 Fixings screw x 4 8. Manual release key x 2
4. Installation
Ensure the gate leaf is securely installed, and has no signs of wear. The gate must move freely with
no unusual friction along the opening and closing. The ground track or cantilever gear and foundation
plate must be fully installed and set solid before installing the electric motor.
The gate must be installed horizontally. Gate leaf must be within size and weight restraints to suit the
motor capability –maximum 7 metres in width and up to 500Kg in weight.
Carefully plan what cables and wiring will be required and where they need to be run.
The condition of the gate and structure directly affects the
reliability and safety of the automated system.

!
!
6!
Installation diagram
1. Motor unit 7. Key switch
2. On board control panel 8. Safety Photocell post
3. Integral radio receiver 9. Safety Photocells
4. Left Limit switch plate 10. Extra Radio Antenna
5. Right Limit switch plate 11. Flashing warning light
6. Drive Rack
Note: Electric cabling should be run in suitable conduit or pipes.
Mains power supply (230V) should be run separately to any low voltage cabling to avoid interference.
5. Setting out the foundation plate
Ensure the foundation plate is able to be securely bolted down or set in concrete before attempting to
install the electric motor

!
!
7!
The foundation plate parallel to the sliding gate leaf, as set out in Fig.09 and 10 below
Ensure the mains power cable is in the centre where the foundation plate is to be mounted.
Bolt foundation plate to concrete (or set in concrete), making sure the power cable is fed up through
cable hole as shown below.
Position Slide motor onto foundation plate

!
!
8!
Adjust the motor position to parallel with gate leaf and ensure the height is correct with drive cog and
intended position of drive rack.
6. Secure motor into position
Secure motor in position with fixing bolts, as Fig.15
Make wiring connections for power supply, motor connection and all accessories, as in accordance to
control panel wiring instructions. (MC1)

!
!
9!
Fix motor lid in place (over mechanical limit device) and screw in place
The Slide motor is supplied with plastic casings that fit over the fixings bolts.
Check the manual release mechanism by inserting the manual release key into the key slot at the
base of the motor.
Ensure that the gate can be moved manually without any significant binding or friction

!
!
10!
7. Install Drive Rack
Install the Drive Rack in accordance with manufacturers specification, ensuring there is sufficient
spacing between drive rack teeth and the gate leaf. Carefully fix the Drive Rack in place so that the
teeth sit neatly and centrally onto the Drive Cog of the Slide motor
Manually move gate leaf open and closed to ensure that the gate still moves freely with no excessive
friction.
8. Install Limit Switch Plates
Install the Limit switch plates onto the drive rack at the required fully open and closed positions, so
that the tab is facing the direction of the motor.

!
!
11!
9. Commission
Once the system has been fully fitted and connected to control panel (MC1), the system needs to be
fully commissioned and tested.
It is recommended to have the sliding gate half open / closed on the first operation, just to ensure that
the motor is running the right direction on the first command.
Ensure that the power supply and motor connections are earthed satisfactorily.
Pay special attention to safety devices.
Check the control panel logic and set up to ensure all suitable functions are activated and
programmed properly.
Fully explain the system to the end user and demonstrate the functions and features that have been
set up.
Demonstrate the manual release mechanism as shown in above.
The automated gate system must be used with due care and attention at all times.
Basic maintenance should be carried out at regular intervals to ensure that the gate system is
operating correctly and safely.
Description of maintenance
Maintenance
Schedule
Clean and check safety Photocells and functions
Monthly
Check free movement of gate manually
Monthly
Clean foliage or insects from gate or control box
Monthly
Check the force of the gate leaf when moving
6 Monthly
Always consult a specialist if any problems occur which are not solved by basic maintenance
Always isolate and disconnect power supply to gate control board and motor before opening control
box or gate motor
Basic Troubleshooting for incorrect operation of motor and control
- Check the power supply and continuity using suitable meter instrument after open and closed
commands have been given.
- The motor is pre-wired to open to the right as standard (when viewed from outside looking in) If
the motor direction is incorrect, such as the gate leaf is to open to the left when it has been given
an open command, the motor wiring will need to be inverted (please refer to MC1 control panel
instructions.) Swap the wires in between Terminals 5 and 7 on CN1.In this case the limit switch
wiring will need to be reversed as well, Terminals 6 and 8 on CN2.
- If the gate control has a problem, disconnect all additional equipment such as intercoms, safety
photocells, push buttons etc. Then run tests on the basic system, then re-connect each item of
equipment individually and test system until the faulty device has been found and isolated.

!
!
12!
Customer copy –to be completed, signed and kept by end user
Gate type: (Swing / Slide etc)
_________________________________________________________________________________
Manufacturer and model of gate: (including material of gate)
_________________________________________________________________________________
(individual number given by installing company)
Installation details and checklist:
Electrical power supply tested
Installed in accordance with manufacturers instructions
Safety devices installed and checked thoroughly
CE Mark applied
Full demonstration carried out with end user
Hand over completed with manual release keys and manuals
The above gate and automation has been assembled, installed, connected and tested in accordance
with manufacturers installation instructions at the site (as stated below) and accordingly is in conformity
with the provisions of the Machinery Directive (89/392/CEE as amended by 91/263/CEE, 92/31/CEE
and 93/68/CEE)
_______________________________________________________________
_______________________________________________________________
(Signature)
_______________________________________________________________
(Print name)
On
_______________________________________________________________
(Date)
On behalf of:
Received by: (Customer signature)
THE MACHINERY TO WHICH THIS DECLARATION OF INCORPORATION RELATES MUST NOT BE PUT INTO
SERVICE UNTIL THE RELEVANT MACHINERY INTO WHICH IT IS TO BE INCORPORATED HAS BEEN
DECLARED IN CONFORMITY WITH THE PROVISIONS OF THE MACHINERY DIRECTIVE
Declaration made by:
Declaration of Conformity & Installation Hand-over
(Responsible Person)
(Company Address)
Unique Serial No.
Gate size:
Operator manufacturer:
Operator model / kit:
Site Address:

!
!
13!
Installer Copy –to be completed, signed and kept by installer
Gate type: (Swing / Slide etc)
_________________________________________________________________________________
Manufacturer and model of gate: (including material of gate)
_________________________________________________________________________________
(individual number given by installing company)
Installation details and checklist:
Electrical power supply tested
Installed in accordance with manufacturers instructions
Safety devices installed and checked thoroughly
CE Mark applied
Full demonstration carried out with end user
Hand over completed with manual release keys and manuals
The above gate and automation has been assembled, installed, connected and tested in accordance
with manufacturers installation instructions at the site (as stated below) and accordingly is in conformity
with the provisions of the Machinery Directive (89/392/CEE as amended by 91/263/CEE, 92/31/CEE
and 93/68/CEE)
_______________________________________________________________
_______________________________________________________________
(Signature)
_______________________________________________________________
(Print name)
On
_______________________________________________________________
(Date)
On behalf of:
Received by: (Customer signature)
THE MACHINERY TO WHICH THIS DECLARATION OF INCORPORATION RELATES MUST NOT BE PUT INTO
SERVICE UNTIL THE RELEVANT MACHINERY INTO WHICH IT IS TO BE INCORPORATED HAS BEEN
DECLARED IN CONFORMITY WITH THE PROVISIONS OF THE MACHINERY DIRECTIVE
Declaration made by:
Declaration of Conformity & Installation Hand-over
(Responsible Person)
(Company Address)
Unique Serial No.
Gate size:
Operator manufacturer:
Operator model / kit:
Site Address: