MSA LUNAR User manual

User Instructions
MSA LUNAR
Order No.: 10214662/00
Print Spec: 10000005389 (EO)
CR 800000046200
MSAsafety.com

© MSA 2021. All rights reserved
WARNING!
Read this manual carefully before using or maintaining the device. The device will perform as designed only if it is used and
maintained in accordance with the manufacturer's instructions. Otherwise, it could fail to perform as designed, and persons
who rely on this device could sustain serious injury or death.
The warranties made by MSA with respect to the product are voided if the product is not installed and used in accordance with
the instructions in this manual. Please protect yourself and your employees by following the instructions.
Please read and observe the WARNINGS and CAUTIONS inside. For additional information relative to use or repair, call 1-
800-MSA-2222 during regular working hours.
MSA is a registered trademark of MSA Technology, LLC in the US, Europe and other Countries. For all other trademarks visit
https://us.msasafety.com/Trademarks.
This product incorporates Bluetooth® wireless technology. The Bluetooth word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc., and any use of such marks by MSA is under license. Other trademarks and trade names are
those of their respective owners.
1000 Cranberry Woods Drive
Cranberry Township, PA 16066
USA
Phone 1-800-MSA-2222
Fax [phone]
For your local MSA contacts, please go to our website www.MSAsafety.com

Contents
1 Safety Regulations 5
1.1 Restrictions 5
1.2 Safety and Precautionary Measures 5
2 Overview 8
2.1 LUNAR 8
2.2 FireGrid 8
2.3 Safety io 8
3 Getting Started 9
3.1 In the Box 9
3.1.1 Accessories and Replacement Parts 9
3.2 Device Overview 10
4 Basic Operation 11
4.1 Attaching LUNARto PPE 11
4.2 Powering On and Off 17
4.2.1 Powering On 17
4.2.2 Powering Off 17
4.3 TIC Display and Connected Device Status 18
4.4 Menus 21
4.4.1 Main Menu 21
4.4.2 Maintenance Menu 21
4.5 Activating an Alarm 22
4.6 Cancelling an Alarm 22
4.7 Pairing with an External Device 23
4.8 Configuring and Maintaining 24
4.8.1 Connecting to FireGrid Configure 24
4.8.2 Updating Firmware 26
4.8.3 Charging the Battery 27
4.8.4 Installing and Removing the Battery 28
4.8.5 Viewing Device Information 29
4.8.6 Viewing Battery Level and Device Assignment (Quick Check) 30
4.8.7 Maintaining LUNAR 30
4.8.8 Before Each Use 30
4.8.9 After Each Use 31
4.8.10 Storing LUNAR 32
5 Features 33
5.1 Starting a Search 33
5.2 Searching Overview 34
5.3 Canceling a Search 35
5.4 Exiting a Search Canceled by the Target 35
5.5 Acknowledging a PAR CheckNotification 36
5.6 Acknowledging an Evacuate Notification 37
6 Learn More 38
MSA LUNAR 3
US

6.1 Support 38
6.2 Specifications 38
6.2.1 Radio 38
6.2.2 Ingress ProtectionRating 38
6.2.3 Single-Point Charger International Input AC Power Plugs 38
6.3 Warranty 38
6.4 Certifications 39
6.4.1 Certified Temperature Ranges 39
6.4.2 Declaration of Conformity 39
6.5 Legal Notices 39
4 MSA LUNAR
US

1 Safety Regulations
US
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the User's authority to
operate the equipment.
Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes au (x) RSS (s) exemptés de licence
d'Innovation, Sciences et Développement économique Canada. L'opération est soumise aux deux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences
(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant provoquer un fonctionnement
indésirable de l'appareil
1.1 Restrictions
MSA LUNAR is not suitable for the following applications:
• Although the thermal imaging camera (TIC) is waterproof, it is unable to take underwater images.
• Likewise, the camera does not take images through glass, water or shiny surfaces which may reflect infrared light and may
appear as a thermal image "mirror".
• The camera does not improve the user's sight. Corrective spectacles must continue to be worn.
Limitations
• Certified ambient operating temperature range: -25°C ≤ Tamb ≤ +40°C.
• Failure to properly use and maintain this product can result in injury or death.
• Never substitute, modify, add or omit parts. Use only exact replacement parts in the configuration as specified by the
manufacturer.
• Refer to user instructions in this manual for information on use and maintenance of this device.
• Refer to user instructions in this manual before use.
• This device contains a battery and electronics. Dispose of or recycle in accordance with all applicable federal state and
local regulations.
1.2 Safety and Precautionary Measures
WARNING!
The User must be trained and thoroughly familiar with proper operation and limitations of the device. Use in controlled live-burn
exercises is suggested before using the device in actual emergency situations.
MSA LUNAR 5
US 1 Safety Regulations

Do NOT rely on the device as the sole means of navigation, search and rescue, or alarm of a Target in distress. Do NOT
deviate from standard firefighting navigational, search and rescue, or operating procedures and best practices during use.
Radio-frequency based search and rescue technology is not a replacement for these procedures. Although the system
provides an image in dark and smoky environments, the User may become disoriented or lost in such environments if the
system becomes inoperative.
If a local alarm network or LTE network interruption occurs, or communication of devices or Cloud connectivity is slowed or
prevented, standard firefighting navigational, search and rescue, and operating procedures must be followed.
Wireless and Bluetooth Operation is dependent upon signal availability of the wireless service(s) necessary to maintain the
communication link. Loss of wireless signal will prevent communication of alarms and other information to linked devices and
will prevent the use of LUNAR search capabilities. Take appropriate precautions in the event a loss of wireless signal occurs.
The search functionality is dependent upon the Target of the search having an operational, connected LUNAR device that is
powered on, connected through wireless signal, and on the Target’s person. If the LUNAR device is not operational, powered
on, and connected through wireless signal, the Target will not be able to be searched. If the LUNAR device is not on the
Target’s person, the search function will lead searchers to the LUNAR device rather than the Target.
If the LUNAR device does not operate correctly as described in these instructions, remove the LUNAR device from service.
Make sure an MSA trained and certified repair technician corrects the unsatisfactory condition before returning the LUNAR
device to service. This device is NOT field serviceable.
Repair or alteration of the device beyond the procedures described in this manual or by anyone other than a person authorized
by MSA could cause the unit to fail to perform properly. Use only genuine MSA replacement parts when performing any
maintenance procedures described in this manual. Substitution of components can seriously impair performance of the unit,
alter intrinsic safety characteristics, or void agency approvals.
Before and after each use, inspect the device to determine if servicing is required. Do not use if the device does not power on
successfully or if device is bent, cracked, modified, or otherwise compromised.
Exposure to high temperature environments for an extended period of time may cause degradation or loss of thermal image.
Avoid heat saturation or overexposure of the equipment. If degradation of the thermal image is observed, immediately remove
the equipment from the high heat environment and allow it to cool until the thermal image returns to normal; otherwise, the
system may become inoperative.
DoNOT mark the device with stamps, labels, paint, or other method. Use of such markings may interfere with camera use or
may constitute a flammability hazard.
Do NOT charge LUNAR in explosive atmospheres.
Only charge LUNAR and LUNAR battery packs indoors.
Only charge the LUNAR battery in temperatures between 0°C (32°F) and 40°C (104°F).
Only charge LUNAR or LUNAR batteries with the Single-Point Charger or Universal Multi-Bay Charger with power supplies
provided by MSA at time of purchase.
Do NOT use a rechargeable battery charging system, which includes the Single-Point Charger or Universal Multi-Bay Charger,
power supply and power cords, if any component of the system shows damage. Replace the components if they show cracks
or distortion, or if the cord shows damage or wear.
Keep LUNAR and rechargeable battery charging system dry. Do NOT disassemble, repair, or alter LUNAR or charging
system. Do NOT immerse in water or other liquids.
Do NOT expose the rechargeable battery or charging system to high temperature or heating equipment including, but not
limited to, direct sunlight and water heaters. Overheating may cause an explosion.
6 MSA LUNAR
1 Safety Regulations US

Do NOT drop, crush or puncture the rechargeable battery or charging system. Damage from such occurrences can lead to
short-circuit and overheating of the equipment.
To prevent electric shock or fire, do not remove the cover or tamper with the case of the power supplies provided in each
charging system. There are no user-serviceable parts inside. The power supplies contain hazardous voltages and must not be
opened. Do not use if any damage to the power supply is observed, including bent prongs, cracked case, modified or
compromised. To avoid the possibility of electric shock, disconnect electric power to the power supply before connecting or
disconnecting the power supply to the charger clip or charger bay.
POWER SUPPLIES for Universal Multi-Bay Charger: AC Mains voltage must be provided to the power supply by a power
supply cord approved tothe national standards in which it will be used.
FUSING: Internal fuse for Line is provided in the power supply. A blown internal fuse is an indication of critical condition of
circuit component(s). If you suspect a blown fuse, do NOT use the device. Return to MSA for service.
Do NOT dispose of batteries in a fire. Batteries can explode. Dispose of in accordance with local regulations and
requirements.
Do NOT replace the battery with another type of battery. Use only LUNAR battery packs. Use of an incorrect battery type
creates a risk of explosion.
Do NOT use a rechargeable battery pack that shows signs of damage such as bulging, swelling, leaking fluid, a cracked
housing, or broken contacts.
Do NOT attempt to open the housing of the rechargeable battery pack. The rechargeable battery pack does not have
replaceable cells.
Failure to follow these warnings can result in serious personal injury or death.
WARNING!/AVERTISSEMENT!
Risk of explosion if battery is replaced with incorrect type.
Dispose of used batteries according to instructions. Do not disassemble, short circuit, or dispose of in fire.
Failure to follow these warnings can result in serious personal injury or death.
Risque d'explosion si la batterie est remplacée par un type incorrect.
Débarrassez-vous des piles usagées selon les instructions. Ne pas démonter, court-circuiter ou ne vous disposer dans le feu.
Le non-respect de ces avertissements peut entraîner des blessures graves ou la mort.
MSA LUNAR 7
US 1 Safety Regulations

2 Overview
2.1 LUNAR
LUNAR is a wireless handheld search and rescue device that includes firefighter-to-firefighter ranging using direction and
distance indicators, edge detection enhanced thermal imaging, and cloud connectivity to FireGrid. It can be utilized
independently of an SCBA - providing accountability to all firefighters on-scene.
LUNAR is not a substitute for standard techniques and precautionary measures. Users must continue to ensure standard
operational processes are observed and maintained while using the device.
2.2 FireGrid
FireGrid is a cloud-based software platform that helps to improve firefighter safety by increasing a department’s capability for
managing products, people, and processes.
This platform includes the following:
• FireGrid Configure (mobile app)
• FireGrid Monitor (mobile app)
• FireGrid (web platform)
Learn more about FireGrid at https://us.msasafety.com/connected-firefighter.
2.3 Safety io
Safety io, LLC (a subsidiary of MSA The Safety Company) developed the FireGrid platform so that, among other things,
LUNAR users can proactively and easily manage and monitor their devices.
For more information, visit http://www.safetyio.com.
8 MSA LUNAR
2 Overview US

3 Getting Started
3.1 In the Box
LUNAR comes with the following components:
• LUNAR Device
• LUNAR Battery
• Single-Point Charger
• LUNAR Quick Start Guide ( 10215367)
• LUNAR Registration Guide (for registering a LUNAR device in FireGrid) ( 10215366)
3.1.1 Accessories and Replacement Parts
Accessories and replacement parts can be purchased separately at https://us.msasafety.com/.
Accessories
Product Part Number Description
Retractor Assembly 10203941 Used to tether LUNAR to an SCBA. See "Attaching
LUNARto PPE" for more information.
Replacement Parts
Product Part Number Description
LUNAR Battery 10214756 The LUNAR device's removable, rechargeable power
supply. Replace battery pack with LUNAR Battery
MSA Part Number 10214756.
Boot 10214762 Rubber cover that wraps around the LUNAR device
to protect from damage, corrosion, or deformation.
Quick-Disconnect Swivel 10214763 Connects to LUNAR so the device can be tethered
to, for example, an external device or Turnout Gear.
Charging Products
Product PartNumber Description
Single-Point Charger
NNA 10214758 Allows charging of one LUNAR device or battery.
Europe 10214759
UK/HK/SG 10214760
AS/NZS 10214761
Universal Multi-Bay Charger
NNA 10214752 Allows charging of up to six LUNAR batteries at one
time.
Europe 10214753
UK/HK/SG 10214754
AS/NZS 10214755
MSA LUNAR 9
US 3 Getting Started

3.2 Device Overview
01 Status
02 ID
03 LTE connection
04 Bluetooth connection
05 Battery level
06 Display
07 TIC lens
08 'Enter' button. Press to select.
09 LED
10 'Down' button. Press to scroll.
11 RFIDtag
12 Quick-Disconnect Swivel
10 MSA LUNAR
3 Getting Started US

4 Basic Operation
4.1 Attaching LUNARto PPE
LUNAR can be tethered to an SCBA using an MSA Retractor Assembly.
WARNING!
Ensure LUNAR is securely attached using a tether by following the instructions below for donning LUNAR.
If using a tether other than the MSA Retractor Assembly, ensure that the tether material and connection method are capable of
withstanding the loading and environmental conditions that will be encountered during use.
Failure to follow this warning can result in serious personal injury or death.
Retractor Assembly Components
01 Split D-ring
02 Retractor
03 Quick-Disconnect Swivel
04 Swivel Button
05 Swivel End
First, remove the Quick-Disconnect Swivel (03) that comes attached to the bottom of LUNAR:
MSA LUNAR 11
US 4 Basic Operation

(1) Push and hold in the LUNAR Swivel Button (04).
(2) With the button depressed, pull the Quick-Disconnect Swivel (03) to
remove.
Then follow the instructions for the applicable SCBA:
•Tethering LUNARto a G1 SCBA
•Tethering LUNARto an M1 SCBA
Tethering LUNARto a G1 SCBA
(1) Identify the G1 SCBAshoulder strap webbing
loop (07) within the strap tunnel (06) on the
User’s left-hand side.
12 MSA LUNAR
4 Basic Operation US

(2) Slide the Retractor (02) up the G1 SCBA strap
tunnel (06) until the Split D-ring (01) is above the
specified stitch.
(3) From outside of the G1 SCBA strap tunnel (06),
secure the Retractor (02).
(4) Reach into the G1 SCBA side access tunnel
(08). At this point, the Split D-ring (01) should be
in front of the webbing.
MSA LUNAR 13
US 4 Basic Operation

(5) Fold the G1 SCBAshoulder strap webbing until
one end can feed between the gap in the Split
D-ring (01).
(6) Work the rest of the G1 SCBAshoulder strap
webbing through the gap. The Split D-ring (01)
should now be fully supported by the specified
stitching loop.
(7) Attach the Retractor (02) to the bottom of
LUNAR:
a) Push and hold in theRetractor Swivel Button
(04).
b) Insert the Swivel End (05) into the bottom of
LUNAR.
(8) Release the Retractor Swivel Button (04) and
ensure that Retractor Assembly is connected
and swiveling freely.
14 MSA LUNAR
4 Basic Operation US

Tethering LUNARto an M1 SCBA
(1) Identify the M1 SCBAshoulder strap webbing
loop (09). It sits on the User’s right-hand side,
one loop above the strap adjustment.
(2) Slide the webbing loop (09) between the gap in
the Split D-ring (01) until half of the webbing is
within the Split D-ring and half of the webbing is
underneath it.
(3) Grip the Retractor (02) and pull forcefully to the
User’s right. Fold the webbing loop (09) under
the Split D-ring (01) until it is able to slide
between the gap and within the Split D-ring.
Note that the stitching on these loops is robust
and can handle the amount of force required.
MSA LUNAR 15
US 4 Basic Operation

(4) Flatten out the webbing loop (09) once it is fully
contained within the Split-D ring.
(5) Attach the Retractor (02) to the bottom of
LUNAR:
a) Push and hold in theRetractor Swivel Button
(04).
b) Insert the Swivel End (05) into the bottom of
LUNAR.
(6) Release the Retractor Swivel Button (04) and
ensure that Retractor Assembly is connected
and swiveling freely.
16 MSA LUNAR
4 Basic Operation US

Orienting LUNAR
The LUNAR device directional search antenna is
aligned with the axis of the Thermal Imaging Camera
(TIC).
The directional search signal you receive is the signal
from the area shown in the thermal image.
4.2 Powering On and Off
4.2.1 Powering On
Long press the Down or Enter button.
NOTES:
Installing a charged battery also powers on the device. See
"Installing and Removing the Battery".
Attempting to power on a LUNAR device with a low battery level
results in a flashing Low Battery icon, and LUNAR shuts down. See
"Charging the Battery".
4.2.2 Powering Off
(1) Open the main menu.
(2) Select SHUTDOWN.
(3) Select YES to confirm shutdown.
MSA LUNAR 17
US 4 Basic Operation

NOTE: LUNARcannot be powered off or enter Search
mode during a Manual, Motion, or Hardware alarm.
4.3 TIC Display and Connected Device Status
The Thermal Imaging Camera (TIC) Display is the default LUNAR screen. From this screen, the configured TIC palettes can
be scrolled by pressing the Down button. If LUNARis connected to Bluetooth and paired with an external device, the status of
the connected device can also be viewed.
NOTE: If LUNAR is not connected to Bluetooth or if the connection is lost, the Status screen will not be available.
18 MSA LUNAR
4 Basic Operation US

Status Icons
Icon Description
Device is working with alarm network enabled.
Device is working with alert network disabled.
Search Mode
Low Battery Alarm
Manual Alarm
Evacuation Alarm
Hardware Alarm
Motion Alarm
Low Pressure Alarm
PAR Check
Strong LTE Connection
Moderate LTE Connection
Weak LTE Connection
No LTE Connection
Battery Level at 100%-75%
Battery Level at 75%-50%
Battery Level at 50%-25%
Battery Level at 25%-0%
Bluetooth Connection On
MSA LUNAR 19
US 4 Basic Operation

Icon Description
Bluetooth Connection Off
Notification Banner
Notifications and alarms are displayed in the notification banner (01). The notification type determines the color of the banner
along with the LED (02) color and behavior.
(01) Notification Banner Color (02) LED
Notifications and Alerts Normal operation
Alarms Paired with external device
Alarm
Notifications and alerts
NOTE: Initially, the LED blinks at
the rate of the notification sound.
Once the sound stops, the blink rate
is slow.
Notification and Alert Types
Motion Pre-Alarm Evacuate
PAR Check SCBA/External Device Connection Lost
PAR Check Acknowledged No LTE Connection
Target Signal Lost SCBA/External Device Low Pressure Alarm
Evacuate Acknowledged LUNAR Low Battery Warning
Firefighter Alarm SCBA/External Device Low Battery Warning
20 MSA LUNAR
4 Basic Operation US