NEC ELECTRA ELITE IPK II User guide

Notice
Note that when converting this document from its original format to a
.pdf file, some minor font and format changes may occur. When
viewing and printing this document, we cannot guarantee that your
specific PC or printer will support all of the fonts or graphics.
Therefore, when you view the document, fonts may be substituted and
your individual printer may not have the capability to print the
document correctly.

SYSTEM HARDWARE
MANUAL
INT-1076 (IPK II)
D
OCUMENT R EVISION 3
(V
ERSION 2000)

NEC Unified Solutions, Inc. reserves the right to change the specifications,
functions, or features at any time without notice.
NEC Unified Solutions, Inc. has prepared this document for use by its
employees and customers. The information contained herein is the property of
NEC Unified Solutions, Inc. and shall not be reproduced without prior written
approval of NEC Unified Solutions, Inc.
Dterm and NEAX is a registered trademark of NEC Corporation and Electra Elite is
a registered trademark of NEC America, Inc. Windows is a registered trademark
of Microsoft Corporation. AT&T is a registered trademark of AT&T Wireless
Services, Inc.
Copyright 2006
NEC Infrontia, Inc.
6535 N. State Highway 161
Irving, TX 75039-2402
Technology Development

___________________________________________________________________________________
Preface
GENERAL
INFORMATION Congratulations! You have purchased the NEC Electra Elite IPK II System.
The feature-rich Electra Elite IPK II key system provides over 200 features including
Computer Telephony Integration, Least Cost Routing, Automatic Call Distribution, T1,
ISDN-BRI Voice Trunks, ISDN-PRI Voice Trunks, Voice over Internet Protocol, and
many others.
The Electra Elite IPK II system provides what the customer needs today, and as
business expands the system can be expanded to grow as well.
The Electra Elite IPK II system has a set of manuals that provide all the information
necessary to install and support the system. This preface describes these manuals.
THIS MANUAL This manual contains detailed instructions to install the Electra Elite IPK II KSUs,
ETUs, Multiline Terminals, and optional equipment in the following chapters.
Chapter 1 – Regulatory Information
This chapter provides important regulatory information.
Chapter 2 – Introduction
This chapter provides an overview of the Electra Elite IPK II system.
Chapter 3– System Specifications
This chapter contains detailed specifications for the Electra Elite IPK II system and
should be carefully reviewed by the technician before installing the system.
Chapter 4 – Hardware Requirements
This chapter contains the hardware requirements for the Electra Elite IPK II system
and should be read by the technician before installing the system.
Chapter 5 – Installing KSUs
This chapter contains the information necessary for installing the basic and expansion
KSUs. The technician should become familiar with this section before starting
installation.

Chapter 6 – Installing ETUs (Circuit Cards)
This chapter contains instructions to install the Electronic Telephone Units (ETUs) in
the Basic and Expansion KSUs.
Chapter 7 – Installing Electra Elite IPK II KSU Common Optional Equipment
This chapter provides information regarding Music on Hold, Station Background
Music and external paging.
Chapter 8 – Installing Electra Elite IPK Multiline Terminals
This chapter describes the Electra Elite IPK Multiline Terminals that can be used with
the Electra Elite IPK II system and provides installation instructions for each
telephone.
Chapter 9 – Installing Electra Elite IPK II Optional Terminal Equipment
This chapter contains installation instructions for Electra Elite IPK II optional
equipment that can be added to the system as a customer’s business grows.
Chapter 10– Installing Electra Elite Multiline Terminals
This chapter describes the available Electra Elite Multiline Terminals that can be used
with the Electra Elite IPK II system and provides installation instructions for each
telephone.
Chapter 11 – Installing Electra Elite Optional Terminal Equipment
This chapter contains installation instructions for installing Electra Elite optional
equipment that can be added to the Electra Elite IPK II as a customer’s business
grows.
Chapter 12 – Installing Single Line Telephones
This chapter describes the single line telephones that are compatible with the Electra
Elite IPK II system. Installation instructions are provided where necessary.

Chapter 13 – Installing Cordless and Wireless Telephones
This chapter describes the cordless and wireless telephones that are compatible with
the Electra Elite IPK II system and provides installation instructions where necessary.
Chapter 14 – System Maintenance
This chapter is a guide to help the technician troubleshoot and diagnose problems
during and after system installation.
Appendix A – Glossary of Abbreviations
This chapter provides a list of commonly used abbreviations that are found
throughout the manual.
SUPPORTING
DOCUMENTS Other manuals in the set are described below.
Electra Elite IPK II Features and Specifications Manual
This manual describes each available feature for the system.
Electra Elite IPK II General Description Manual
This manual contains general information about the system features, configuration
and standards. This overview of the Electra Elite IPK II system is useful when
presenting information to potential customers.
Electra Elite IPK II Programming Manual
This manual contains all programming instructions for the Electra Elite IPK II system.
Electra Elite IPK II PC Programming Manual
This manual describes the operation of the PCPro program for the Electra Elite IPK II
key telephone system. This program is a user-friendly Windows application that
allows the user to program and configure features of the Electra Elite IPK II KTS from
the PC environment.

THIS PAGE INTENTIONALLY LEFT BLANK

System Hardware Manual i
___________________________________________________________________________________
___________________________________________________________________________________
TABLE OF CONTENTS
Chapter 1
Section 1 General Information ....................................................................................... 1-1
Section 2 Company Notification .................................................................................... 1-1
Section 3 Incidence of Harm .......................................................................................... 1-2
Section 4 Radio Frequency Interference ....................................................................... 1-3
Section 5 Hearing Aid Compatibility ............................................................................. 1-3
Section 6 Direct Inward Dialing ...................................................................................... 1-3
Section 7 Voice Announcement/Monitoring Over DID Lines ...................................... 1-4
Section 8 Music On Hold ................................................................................................ 1-4
Section 9 Service Requirements .................................................................................... 1-4
Section 10 UL Regulatory Information ............................................................................ 1-4
Section 11 Industry Canada Requirements .................................................................... 1-5
Section 12 Battery Disposal ............................................................................................. 1-6

ii Table of Contents
___________________________________________________________________________________
___________________________________________________________________________________
Document Revision 3 Electra Elite IPK II
THIS PAGE INTENTIONALLY LEFT BLANK

System Hardware Manual iii
___________________________________________________________________________________
___________________________________________________________________________________
List Of tables
Chapter 1
Table 1-1 FIC, REN, SOC, and Jacks for Electra Elite IPK II System ETUs ..............................1-2
Table 1-2 Battery Types and Quantities for KSUs and ETUs .....................................................1-6

___________________________________________________________________________________
Document Revision 3 Electra Elite IPK II
iv List of Tables
___________________________________________________________________________________
THIS PAGE INTENTIONALLY LEFT BLANK

System Hardware Manual 1 - 1
___________________________________________________________________________________
___________________________________________________________________________________
Regulatory Information Chapter 1
SECTION 1GENERAL INFORMATION
Established Federal Communications Commission (FCC) rules permit this telephone
system to be directly connected to the telephone network. A jack is provided by the
telephone company. Jacks for this type of customer provided equipment are not
provided on party lines or coin lines.
The telephone company may change technical operations and procedures. When
such changes affect the compatibility or use of the Electra Elite IPK II system, the
telephone company is required to give adequate notice of the changes.
SECTION 2COMPANY NOTIFICATION
Before connecting this telephone system to the telephone network, the following
information must be provided to the telephone company:
1. Your telephone Number.
2. FCC registration number:
J When the system is to be installed as a Key Function system (no dial
access to Trunk Groups/Route Advance Blocks), use the following
number:
NIFMUL-43074-KF-E
J When the system is to be installed as a Multifunction system, use the
following number:
NIFMUL-43076-MF-E
J When the system is to be installed as a PBX system, use the following
number:
NIFMUL-43075-PF-E
J Ringer Equivalence Number (REN): 2.0B
J USOC jacks required: RJ21X and RJ2GX

___________________________________________________________________________________
1 - 2 Regulatory Information
___________________________________________________________________________________
Document Revision 3 Electra Elite IPK II
The Facility Interface Code (FIC), Ringer Equivalent Number (REN), Service Order
Code (SOC), and Jack for each interface ETU are listed in the following table:
SECTION 3INCIDENCE OF HARM
When the system is malfunctioning, it could harm the telephone network. The
telephone system should be disconnected until the problem can be determined and
repair is made. When this is not done, the telephone company may temporarily
disconnect service.
Table 1-1 FIC, REN, SOC, and Jacks for Electra Elite IPK II System ETUs
Trunk/Station ETU Type FIC REN SOC Jack
BRT(4)-U( ) ETU 02IS5 N/A 6.0F N/A
CAMA Trunk 02RV-O 0.7A 9.0F RJ21X
COI(4)-U( ) ETU (Loop Start) 02LS2 0.7A 9.0F RJ21X
COI(8)-U( ) ETU (Loop Start) 02LS2 0.7A 9.0F RJ21X
COI(8)-U( ) ETU (Ground Start) 02GS2 0.7A 9.0F RJ21X
COIB(4)-U(10) ETU for COI/COID
Mode (Loop Start) 02LS2 0.7A 9.0F RJ21X
COIB(4)-U(10) ETU for COI Mode
(Ground Start) 02GS2 0.7A 9.0F RJ21X
COIB(4)-U(20) ETU for COID/COI
Mode (Loop Start) 02LS2 0.7A 9.0F RJ21X
COIB(8)-U( ) ETU for COI/COID
Mode (Loop Start) 02LS2 0.7A 9.0F RJ21X
DID(4)-U( ) ETU 02RV2T N/A 9.0F RJ21X
DTI-U( ) ETU
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
N/A 6.0P N/A
OPX(2)-U( ) ETU 0L13C N/A 9.0F RJ21X
TLI(2)-U( ) ETU TL31M N/A 9.0F RJ21X

Electra Elite IPK II Document Revision 3
System Hardware Manual 1 - 3
___________________________________________________________________________________
___________________________________________________________________________________
SECTION 4RADIO FREQUENCY INTERFERENCE
In compliance with FCC Part 15 rules, the following statement is provided:
IMPORTANT NOTE
“This equipment generates, uses, and can radiate radio frequency energy and when not
installed and used in accordance with the System Hardware Manual, may cause interference
to radio communications. This equipment has been tested and approved for compliance with
the limits for a Class B (except as noted below) computing device pursuant to Subpart J of
Part 15 of FCC Rules, that provide reasonable protection against such interference when
operated in a commercial environment. Operation of this telephone system in a residential
area is likely to cause interference, in which case, the user, at his or her own expense, is
required to take whatever measures may be required to correct the interference.”
 When equipped with the B64-U30 KSU and P64-U20 PSU, the Electra Elite IPK II can
be operated as a Class B device except when using one of the ETUs in the following
table. The system then becomes a Class A device that may not be used in a residential
area.
SECTION 5HEARING AID COMPATIBILITY
The NEC Multiline Terminals and NEC Single Line Telephones provided for this
system are hearing aid compatible. The manufacturer of other Single Line
Telephones for use with the system must provide notice of hearing aid compatibility to
comply with FCC rules that prohibit the use of non-hearing aid compatible telephones.
SECTION 6DIRECT INWARD DIALING
Operating this equipment without providing proper answer supervision isa violation of
Part 68 of the FCC rules.
Proper Answer Supervision occurs when:
J This equipment returns answer supervision to the Public Switched Telephone
Network (PSTN) when Direct Inward Dialing (DID) calls are:
H Answered by the called station.
H Answered by the Attendant.
H Routed to a recorded announcement that can be administered by the
Customer Premise Equipment (CPE) user.
H Routed to a dial prompt.
CCH(4)-U-10 CMS(2)/(4)-U30 FMS(2)/(4)/(8)-U30 HUB(8)-U( )
VMS(2)/(4)/(8)-U30

___________________________________________________________________________________
1 - 4 Regulatory Information
___________________________________________________________________________________
Document Revision 3 Electra Elite IPK II
J This equipment returns answer supervision on all DID calls forwarded to the
Public Switched Telephone Network (PSTN). Permissible exceptions are:
H A call is unanswered.
H A busy tone is received.
H A reorder tone is received.
SECTION 7VOICE ANNOUNCEMENT/MONITORING OVER DID LINES
CAUTION
The use of monitoring, recording or listening devices to eavesdrop, monitor, retrieve or record
telephone conversations or other sound activities, whether or not contemporaneous with its
transmission, may be illegal in certain circumstances under federal or state laws. Legal advise
should be sought prior to implementing any practice that monitors or records any telephone
conversation. Some federal and state laws require some form of notification to all parties to
the telephone conversation, such as using a beep tone or other notification methods, or
require the consent of all parties to the telephone conversation, prior to monitoring or
recording a telephone conversation. Some of these laws incorporate strict penalties.
SECTION 8MUSIC ONHOLD
IMPORTANT NOTE
"In accordance with U.S. Copyright Law, a license may be required from the American Society
of Composers, Authors and Publishers, or other similar organization, when radio or TV
broadcasts are transmitted through the Music On Hold feature of this telecommunication
system. NEC Unified Solutions, Inc., hereby disclaims any liability arising out of the failure to
obtain such a license."
SECTION 9SERVICE REQUIREMENTS
When equipment malfunctions, all repairs will be performed by NEC Unified
Solutions, Inc. or by an authorized agent. The user must report the need for service to
an NEC Unified Solutions, Inc. authorized agent or to NEC Unified Solutions, Inc.
SECTION 10 UL REGULATORY INFORMATION
This equipment has been listed by Underwriters Laboratories and complies with all
applicable requirements of the standard for telephone equipment UL 1459.

Electra Elite IPK II Document Revision 3
System Hardware Manual 1 - 5
___________________________________________________________________________________
___________________________________________________________________________________
SECTION 11 INDUSTRY CANADA REQUIREMENTS
Industry Canada has established rules that permit this telephone system tobe directly
connected to the telephone network. Prior to the connection or disconnection of this
telephone system to or from the telephone network, the telephone company must be
provided with the following information.
1. Your telephone number:
2. IC Certificate number: 140 7942 A
3. Ringer Equivalence Number (REN) of the equipment: 2.1
The Industry Canada label identifies certified equipment. This certification means that
the equipment meets certain telecommunications network protective, operational and
safety requirements as prescribed in the applicable Terminal Equipment Technical
requirements document(s). The Department does not guarantee that equipment
operates to user satisfaction.
Before installation, the user should ensure that it is permissible to connect this
equipment to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated
by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request
the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, when
present, are connected together. This precaution may be particularly important in
rural areas.
CAUTION
Users should not attempt to make such connections themselves, but should contact the
applicable electric inspection authority, or electrician.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination of an interface may consist of any combination
of devices subject only to the requirement that the sum of the Ringer Equivalent
Numbers of all the devices does not exceed five.
This equipment is listed by the Canadian Standards Association and complies with all
applicable requirements of the standard for telephone equipment C 22.2 No. 225.

___________________________________________________________________________________
1 - 6 Regulatory Information
___________________________________________________________________________________
Document Revision 3 Electra Elite IPK II
This equipment meets IC requirements CS03.
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus as regulated by the radio interference regulations of Industry
Canada.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les
limites applicables aux appareils numeriques de Classe A prescrites dans le
reglement sur le brouillage radioelectrique edicte par Industrie Canada.
SECTION 12 BATTERY DISPOSAL
The Electra Elite IPK II system includes the batteries listed below. When disposing of
these batteries, KSUs, and/or ETUs, you must comply with applicable federal and
state regulations regarding proper disposal procedures.
The Electra Elite IPK II CPUII( )-U( ) ETU provides memory backup forapproximately
three years. The Lithium battery should be replaced about every two years.
Table 1-2 Battery Types and Quantities for KSUs and ETUs
Unit Name Type of Battery Quantity
B64-U20 KSU Lead Acid 2
CPUII( )-U( ) ETU Lithium 1
CTI/VP(4)/(8)/(12)/(16)-U( ) ETU Lithium 1
DTP-1HM-1 TEL
DTP-1HM-2 TEL Lithium 1
DTP-16HC-1 TEL Nickel-Cadmium 1
DTR-1HM-1 TEL Lithium 1
DTH-4R-1/2 TEL Nickel-Cadmium 1
DTR-4R-1/2 TEL Nickel-Cadmium 1
DTU-4R-1 TEL Lead Acid 1
FMS(2)/(4)/(8)-U( ) ETU Nickel-Cadmium 1
VMS(2)/(4)/(8)-U( ) ETU Lithium 1