Neilsen CT2283 User manual

1/2” DR AIR RATCHET CT2283
ORIGINAL INSTRUCTIONS
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety
and health requirements of the EC Directive based on its design and type, as
brought into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: 1/2” DR AIR RATCHET
Model: CT2283
Applicable EC Directives:
EC Machinery Directive 2006/42/EC
Harmonized standards
EN ISO 11148-6:2012
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2021-03-18

1.SPECIFICATION
Model；CT2283
Max. air pressure: 6.2 bar (90 psi)
No load speed: 180/min
Air consumption: 5.4cfm
Max. torque: 75 ft-lb
Air inlet: 1/4"
2. SAFETY INSTRUCTIONS
•Follow all workshop safety rules, regulations, and conditions when using
wrench.
•Do not wear watches, rings, bracelets or loose clothing when using air tools.
•WARNING! Disconnect from air supply before changing accessories or
servicing.
•Maintain the wrench in good condition and replace any damaged or worn parts.
Use genuine parts only. Non-authorized parts may be dangerous.
•WARNING! Check correct air pressure is maintained and not exceeded. We
recommend 90psi.
•Keep air hose away from heat, oil and sharp edges. Check air hose for wear
before each use and ensure that all connections are secure.
•Only use sockets which are specifically designed for use with a ratchet wrench.
•Wear approved safety eye/face shield, ear defenders, and hand protection.
•WARNING! Due to the possible presence of asbestos dust from brake linings,
when working around vehicle brake systems we recommend you wear suitable
respiratory protection.
•Maintain correct balance and footing. Ensure the floor is not slippery and wear
non-slip shoes.
•Keep children and non essential persons away from the working area.
•DO NOT use the wrench for a task it is not designed to perform.
•DO NOT use wrench if damaged or thought to be faulty.
•DO NOT use wrench unless you have been instructed in its use by a qualified
person.
•DO NOT carry the wrench by the air hose.
•DO NOT direct air from the air hose at yourself or others.
•When not in use disconnect from air supply and store in a safe, dry, childproof
location.

3. TECHNICAL DESCRIPTION
1. Ratchet anvil 1/2”
2. Trigger
3. Reverse bottom
4. Air inlet

4. AIR SUPPLY
1. Ensure tool air valve (or trigger) is in “off ” position before connecting to the air
supply.
2. You will require an air pressure of 90psi, and an air flow according to
specification.
WARNING! Ensure the air supply is clean and does not exceed 90psi while
operating the tool. Too high an air pressure and unclean air will shorten the
product life due to excessive wear, and may be dangerous causing damage
and/or personal injury.
3. Drain the compressor’s air tank daily. Water in the air line will damage the
tool.
4. Clean the compressor’s air inlet filter weekly.
5. Line pressure should be increased to compensate for unusually long air
hoses (over 8 metres). The minimum hose diameter should be 1/4” I.D. and
fittings must have the same inside dimensions.
6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and
make certain that all connections are secure.
7. Vibration may cause failure if a quick change coupling is connected directly to
the tool.
8. To overcome this, connect a leader hose to the tool. A quick change coupling
may then be used to connect the leader hose to the air line recoil hose. See fig 1.

5. OPERATION
WARNING: Ensure you read, understand and apply safety
instructions before use.
General operation instructions
•Attach an air hose (not included) to the compressor’s air outlet. Connect
the air hose to the air inlet of the ratchet wrench.
•The air hose must be long enough to reach the work area with enough
extra length to allow free movement while working.
•Turn on the air compressor according to the manufacturer’s directions
and allow it to build up pressure until it cycles off.
•Push and snap socket (not included) onto the anvil.
•The wrench can be used in either forward or reverse direction by
adjusting the reverse switch.
•To tighten, place the socket over the nut you wish to tighten.
•Hold the handle firmly and place other hand on top of housing. Then gently
squeeze the trigger.
•If tool requires more force to accomplish task in forward or reverse setting,
verify that the tool receives sufficient, unobstructed airflow and increase the
pressure output of regulator up to maximum air pressure rating of tool.
CAUTION! Do not exceed tool’s maximum air pressure rating (6.3 bar).
•If tool still does not have sufficient force at maximum pressure and sufficient
airflow, then a larger tool may be required. When the nut is tightened or
loosened, release the trigger.
Loading and operation
•Only use sockets which are specifically designed for use with the wrench.
•Changing sockets
Disconnect the tool from the source o f compressed air.
Remove the socket you no longer wish to use from the anvil.
Subsequently fit the new socket to the square drive as described
above.
DO NOT use any additional force upon the wrench in order to
remove a nut.
DO NOT allow wrench to free run for an extended period of time
as this will shorten its life.

6. MAINTENANCE
WARNING: Disconnect wrench from air supply before changing accessories,
servicing or performing maintenance. Replace or repair damaged parts. Use
genuine parts only. Non-authorised parts may be dangerous.
1. Lubricate the air wrench daily with a few drops of air tool oil dripped into the
air inlet
2. DO NOT use worn or damaged sockets.
3. Loss of power or erratic action may be due to the following:
Excessive drain on the air line.
Moisture or restriction in the air pipe.
Incorrect size or type of hose connectors.
To remedy check the air supply and follow instructions.
4. Grit or gum deposits in the ratchet wrench may also reduce
performance. If your model has an air strainer (located in the area of
the air inlet), remove the strainer and clean it.
5. When not in use, disconnect from air supply, clean air ratchet wrench
and store in a safe, dry, childproof location.
7. DISPOSAL
At the end of the machine's working life, or when it can no longer be repaired,
ensure that it is disposed of according to national regulations.
Contact your local authority for details of collection schemes in your area.
In all circumstances:
Do not dispose of this tool with domestic waste.
Do not incinerate.
During decommissioning of the equipment, certain hazards should be
understood and avoided:
. Only with the line pressure released shall the equipment be
disassembled.
.Goggles should be worn.

8. SYMBOLS
In this manual and/or on the machine the following symbols are used:
Denotes risk of personal injury, loss of life or damage to the tool in
case of non-observance of the instructions in this manual.
Wear hearing protection.
Wear safety goggles.
Contact with or inhalation of dust coming free during use (e.g.
lead-painted surfaces, wood and metal) can endanger your health
and the health of bystanders. Always wear appropriate protective
equipment, such as a dust mask. Always use proper dust
extraction during use.
Wear gloves.

9. EXPLODED VIEW

CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in China