No Butts Bin SR8060-F User manual

Assembly Instructions
Shelter type: SR8060-F
SR8060F-01-02112021-USA
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]

10
10
18
19 18
17
7
6
6
6
6
22
1
3
17
15
16 15
2
33
2
1
4
4
888
9
11
12
13
11
13
13
14
5
2
Exploded view
Tools required:
Drill/Screwdriver
Mallet
17mm Wrench
T25 Torx bit

3
PARTS LIST
ITEM
NO. PART NAME
DRG NUMBER Size (inch)
IMAGE
QTY.
1 S1C Frame S1C
78.74 x 40.74 6
2 CB1 Bracket CB1
4.3 x 4.3 x 1.57 6
3 JF1 Bracket JF1
4.33 x 1.57 6
4 ST1 Roof Tie ST1
40.35 2
5 40x40 End cap
EC40 1.6 X 1.6 4
6 FT1 Bracket FT1
1.57 x 1.57 x 3.94 4
7 FT3 Bracket FT3
1.57 x 3.15 x 4.17 4
8 DR Bracket DR
4.3 x 1.6 x 2 12
9 AR1R 1m Pitch Rafter AR1R
45 x 11.8 OA 4
10
AR1IS 1m Pitch Infill
Panel Shallow
AR1IS
45.2 x 13.5 2
11
AR1CLTO 1m Apex
Roof Centre Lower
Trim Outer
AR1CLTO
41.4 2
12
AR1CLTI 1m Apex
Roof centre lower trim
inner
AR1CLTI 40.74 1
13 Roof F Section Outer ARFSO
41.5 4
14
ARFSI Apex Roof F
Section Inner
ARFSI
40.75 2
15
AR1POA Roof Panel
outer alu
AR1POA
41.5 x 24.4 4
16
AR1PIA Roof Panel
inner ALU
AR1PIA
40.75 x 24.4 2
17
AR1TS 1m Apex Roof
Trim strips
AR1TS
24.8 x 2.3 4
18
AR1CUTO 1m Apex
Roof centre upper trim
outer
AR1CUTO
41.5 2
19
AR1CUTI 1m Apex
Roof centre upper trim
inner
AR1CUTI
40.75 1

4
FIXINGS
Fittings Bolt set M10 T25 T38 BTANCM12100
M10 x 60mm Nut Washer
1" Tech
screw
1.5"
mm
Tech
screw
Black
Caps
M10/12 x 100 mm
Concrete Bolt
Pack A+B
33 33 66 136 40 66 11
Image

40.75
42.32
123.82
S1C
CB1
CB1
JF1
MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
JF1
Please note 1.5" Tec Screws
are for roof panels only
JF1
JF1
CB1
CB1
JF1JF1
ENSURE CORRECT
ALIGNMENT ON
CORNERS
Step 1
Assemble S1C frames to make up the main structure using CB1 brackets
for the corners and JF1 brackets for the straight joints.
5

ST1
CB1
JF1
CB1
ST1
JF1
S1C
CB1
CB1
JF1
JF1
ST1
ST1
S1C
Step 2
Use JF1 and CB1 brackets to attach the S1C frame and ST1 Tie bars.
6

AR1R
DR
DR
AR1R
AR1R
AR1R
AR1IS
AR1IS
40.75 40.75 40.75
ENSURE CORRECT
ALIGNMENT OF RAFTERS
AND S1 FRAMES
END
PANEL
END
PANEL
Step 3
Attach AR1R rafters using DR brackets. Secure the AR1IS end panels to
S1 frames using 1" tec screws. The end rafters need to be placed in position at
the same time as the end panels.
7

A
Step 4
ARFSO
ARFSO
ARFSO
ARFSI
ARFSI
AR1CLTO
AR1CLTO
AR1CLTI
ARFSO
ARSCLTO
ARSCLTI
ARSCLTO
ARFSO
ARFSO
ARFSI
DETAIL A
SCALE 1 : 2
8
Attach the AR1CLTO and AR1CLTI to the top of the rafters The AR1CLTO are
to be lined up near the end panels and the AR1CLTI have to be spaced
centrally. The ARFSO and ARFSI parts are to be attached to the lower part
of the rafters as shown below. Then the ARSCLTI and ARSCLTO are
attached to the top of the rafters.

AR1POA AR1POA
AR1POA
AR1POA
AR1PIA
AR1TS
AR1TS
AR1CUTO
AR1CUTO
AR1CUTI
FT1
FT1
FT1
FT1
FT3
FT3
FT3
AR1POA
AR1POA
FT3
FT1
FT1
FT3
FT1
FT1
AR1CUTI
AR1CUTO
AR1CUTO
AR1TS
AR1TS
AR1PIA
AR1POA
AR1POA
FT3
9
Step 5
Attach the AR1POA roof panels on the outer edges of the shelter nearest to
the end panels and the AR1PIA pannels need to be equaly spaced along
the centre.
Cap off the top using AR1CUTO and AR1CUTI as shown below.
Use the AR1TS strips to cover the gaps between the panels.
Once the shelter is in the final position and square, it can be scured to
the ground using the FT3 and FT1 brackets and concrete bolts.

45.3
123.98
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 8inch oversized on all 4 sides.