No Butts Bin SR8065 User manual

Assembly Instructions
Shelter type: SR8065
SR8065-01-03112021-USA
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]

17
18
18
17 18
12
2
8
7
12
6
9
15
19
19
19
19
10
6
16 16 16
15
3
1
4
4
55
11
11
13
14 14 14
13
3
20
2
Exploded View
Tools required:
Drill/Screwdriver
Mallet
Wrench
Torx bit

3
PARTS LIST
ITEM
NO. PART NAME
DRG NUMBER Size (inch)
IMAGE
QTY.
1 S1 Frame S1
78.74 x 40.74
11
2 CB1 Bracket CB1
4.3 x 4.3 x 1.57
9
3 JF1 Bracket JF1
4.33 x 1.57
16
4 FT1 Bracket FT1
1.57 x 1.57 x 3.94
3
5 FT3 Bracket FT3
1.57 x 3.15 x 4.17
10
6 DR Bracket DR
4.3 x 1.6 x 2
20
7 ST3 Roof Tie ST3
81.1 1
8 Post P1 P1
78.75 x 40.5
1
9 AR2R 2m Pitch Rafter AR2R-02
85.75 6
10
Roof centre lower trim
outer
AR2CLTO-03
41.4 2
11
Roof centre lower trim
inner
AR2CLTI-02
40.74 3
12
AR2IS 2m Pitch Infill
Panel Shallow
AR2IS-02
85 2
13 Roof F Section Outer ARFSO
41.5 4
14
ARFSI Apex Roof F
Section Inner
ARFSI
40.75 6
15
AR2POA AR2 Roof
Panel outer ALU
AR2POA
45.5 x 41.3
4
16
AR2PIA AR2 Roof
Panel inner ALU
AR2PIA
45.5 x 40.5
6
17
Roof centre upper trim
outer
AR2CUTO-02
41.5 2
18
Roof centre upper trim
inner
AR2CUTI
40.75 3
19
AR2TS 2m Apex Roof
Trim strip
AR2TS-01
45.5 x 2.3
8
20 40x40 Plastic End Cap EC40
1.6 x 1.6
2

4
FIXINGS
Fittings Bolt set M10 T25 T38 BTANCM12100
M10 x 60mm Nut Washer
1" Tech
screw
1.5"
Tech
screw
Black
Caps
M10/12 x 100 mm
Concrete Bolt
Pack A+B
33 33 66 136 40 66 11
Image

83.07
205.31
42.32
S1
CB1
CB1
JF1
CB1
JF1
JF1
JF1
JF1
MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
JF1
Please note 1.5" Tec Screws
are for roof panels only
CB1
CB1
CB1
JF1
JF1
Ensure corect
alignment on all corners
JF1
JF1
S1
JF1
S1
Step 1
Assemble S1 frames to make up the main structure using CB1 brackets
for the Corners and JF1 brackets for the straight joints.
5

ST3
P1
CB1
CB1
JF1
JF1
CB1
ST3
P1
CB1
CB1
JF1
Step 2
Use JF1 and CB1 brackets to attach the P1 post and ST3 Tie bar.
6

AR2IS
AR2IS
AR2R
AR2R
AR2R
AR2R
AR2R
40.75
40.75 40.75 40.75 40.75
DR BRACKETS
Step 3
Attach AR2R rafters using DR brackets. Secure the AR2IS end panels to
S1 frames using tec screws. The end rafters need to be placed in position at
the same time as the AR2IS end panels.
Stick sealing strips to each rafter.
7

Step 4
ARFSO
ARFSO
ARFSO
ARFSO
ARFSI
ARFSI
ARFSI
ARFSI
AR2CLTO
AR2CLTO
AR2CLTI
AR2CLTI
ARFSI
FS3
FS1
FS1
FS1
FS3
FS3
FS3
AR2CLTI
ARSCLTO
ARSCLTI
ARSCLTI
ARSCLTO
ARFSO
ARFSO
ARFSI
ARFSI
ARFSI
ARSCLTI
8
Attach the AR2CLTO and AR2CLTI to the top of the rafters The AR2CLTO are
to be lined up near the end panels and the AR2CLTI have to be spaced
equally along the centre. The ARFSO and ARFSI parts are to be attached to
the lower part of the rafters as shown below.
Once the shelter is in the final position and square, it can be scured to the
ground using the FT3 and FT1 brackets.

AR2POA
AR2POA
AR2POA
AR2POA
AR2PIA
AR2PIA
AR2PIA
AR2PIA
AR2TS
AR2TS
AR2TS
AR2TS
AR2TS AR2TS
AR2CUTO
AR2CUTO
AR2CUTI
AR2CUTI
AR2POA
AR2POA
AR2POA
AR2POA
AR2PIA
AR2PIA
AR2PIA
AR2PIA
AR2TS
AR2TS
AR2TS
AR2TS
AR2TS AR2TS
AR2CUTO
AR2CUTO
AR2CUTI
AR2CUTI
9
Step 5
Attach the AR2POA roof panels on the outer edges of the shelter nearest to
the end panels and the AR2PIA pannels need to be equaly spaced along
the centre.
Cap off the top using AR2CUTO and AR2CUTI as shown below.
use the AR2TS strips to cover the gaps between the panels.

83.07
205.31
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 200mm oversized on all 4 sides.
10