No Butts Bin SR1554 User manual

Assembly Instructions
Shelter type: SR1554
SR1554-05-130219-USA

EXPLODED VIEW AND TOOLS
11
13
12
2
3
8
9
4
7
6
1
5
10
2
Tools required:
Drill/Screwdriver
Mallet
Hack saw
Spanner
Torx bit
ITEM
NO. PART NAME
DRG NUMBER LENGTH Default/QTY.
1 S1 Frame S1
Default
6
2 P1 Post P1
Default
1
3 ST1 Roof Tie ST1
Default
1
4 CB1 Bracket CB1
Default
7
5 JF1 Bracket JF1
Default
7
6 FT1 Bracket FT1
Default
3
7 FT3 Bracket FT3
Default
5
8 RB1 Bracket RB1
Default
8
9 R2 Rafter R2
Default
3
10 Sealing Strip - 2195mm Sealing Strip
Default
4
11 PCE2 - Roof Sheet PCE2
Default
2
12 RC2 - Roof Strip RC1
Default
3
13 2MD Roof Edging 2MD
2110 2
14 40x40 End cap BOUGHT IN ITEM
40 x 40 x
20 9

3
PARTS LIST
Fittings Bolt set M10
Nut Washer
Black
Cap
T25 T38 AB1210
M10 x 60mm
25 mm
Tech
screw
38 mm
Tech
screw
M10/12 x 10mm
Concrete Bolt
Pack A
30 30 60 60 72 30 8
Required 14 14 28 28 68 30 8
Image
ITEM
NO.
PART
NO.
DESCRIPTION
DIMENSION
(MM)
DIMENSION
(INCHES)
IMAGE
QTY.
1 S1 Frame 2000x1035 78.74 x 40.55
6
2 P1 Post 1030x2000 40.55 x 78.74 1
3 ST1 Roof Tie 1025x40x40
40.35 x 1.75 x
1.75 1
4 CB1 Bracket 110x110x40 4.33 x 4.33 7
5 JF1 Bracket 220x40 8.66 x 1.58 6
6 FT1 Foot Bracket 109x100x40 4.29 x 3.93 x
1.57 3
7 FT3 Foot Bracket 109x100x80 4.29 x 3.93 x
3.27 5
8 RB1 Bracket 110x46 4.33 x 1.81 8
9 R2 Rafter 2220x40x40
87.40 x 1.57 x
1.57 3
10 SS Sealing Strip Trim to 2180 Trim to 2180 2 ROLLS
11 PCE2 Roof Panel 2220x1050 87.40 x 41.34 2
12 RC2 Roof Strip 1130 87.40 3
13 2MD
Roof Edge
Trim
Trim To Fit Trim To Fit 3
14 EC40
Plastic end
Cap
40x40 1.57 x 1.57 18

2110
2110
83.07
83.07
IMPORTANT:
Check overall dimensions
to ensure corrct alignment
S1
ST1
JF1
CF1
P1
NOTE: Insert EC40 into ST1
and P1 before installing.
CB1CB1CB1CB1
Ensure corners are aligned
correctly
Step 1
Assemble S1 frames to make up the main structure using CB1 brackets
in the corners and JF1 brackets on straight joints. Then attach P1 Post using
one JF1 bracket.
Then attach ST1 Tie bar using a JF1 bracket and one CB1 bracket.
MEASUREMENTS IN BLUE - MM
MEAUREMENTS IN GREEN - INCHES

1035 1035
FRONT VIEW
R2
RB1
FT1
FT3
Step 2
Move shelter in to its final position, make sure everything is square and
secure to the floor using FT1 and FT3 foot brackets.
Attach R2 roof rafters using RB1 brackets.
5

PCE2
SS
SS
PCE2
Step 3
Apply SS sealing strips to the rafters (two for cental rafter) and line up the PCE2
roof panels to the outside of the shelter, leaving a gap between them.
6

GENERAL NOTE:
THE 38mm TECH SCREWS
ARE FOR FIXING ROOF STRIPS
(RC) ONLY
RC1
MD2
RC1
MD2
Step 4
Apply RC2 strips on top of the panels and use 38mm Tech screws to
secure them in place, drilling through the panels and into the rafters.
Then clip on the 2MD edge trim to the edges of the roof panels, tapping
it on with a mallet. Then fit the Black plastic caps on exposed nuts and
bolts. Fit the square plastic end caps ( EC40 ) to any open ends of box
sections.
7

1044.50 1035
1044.50 1035
1044.50 1136.50
1035 995
2181
2181
40.75 41.12
40.75
39.17
40.75 41.12
85.87
41.12 44.74
Ground anchor positions and overall size
Suggested concrete base size: 200mm/7.87in oversized on all four sides
Scale 1:15
8

NOTES
:
9

NOTES
:
10

NOTES
:
11

12
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
CONTACT DETAILS:
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]
No Butts Bin Company, Inc. 16 Birch Lane, Madison, CT 06443
All Parts and Fixings checked by:
Print Name: Signature: