NordicTrack Revitalize 831.14595.0 User manual

Model No. 831.1 4595.0
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As amanufacturer, we are corn =
mitted to providing complete
customer satisfaction, if you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL=FREE:
1-888-825-2588
Mon.-gri., 6 a.m.-6 p.m. MST
ON THE WEB:
www.nordictrackservice.com
_k CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S UAL
www.nordictrack.com
new products, prizes,
fitness tips, and much more!

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ................................................................ 3
BEFORE YOU BEGIN ...................................................................... 4
PART IDENTIFICATION CHART .............................................................. 5
ASSEMBLY .............................................................................. 6
ADJUSTMENT ........................................................................... 12
ROTATING ON THE iNVERSiON TABLE ...................................................... 14
DEVELOPING A PROGRAM ................................................................ 15
PART LiST .............................................................................. 18
EXPLODED DRAWING .................................................................... 19
ORDERING REPLACEMENT PARTS .................................................. Back Cover
LiMiTED WARRANTY .............................................................. Back Cover
NordicTrack is a registered trademark of ICON IP, Inc.
2

iMPORTANT PRECAUTIONS
_WARNING:
before using the inversion table.
1. Read all instructions in this manual before
,
To reduce the risk of serious injury, read the following important precautions
using the inversion table. Use the inversion
table only as described in this manual.
it is the responsibility of the owner to ensure
that all users of the inversion table are ade-
quately informed of all precautions.
the short knob is fully tightened before you
use the inversion table.
13. Perform all activities on the inversion table in
aslow, controlled manner. Agg ressive exer-
cise can cause the inversion table to tip over.
14. Always exercise with a partner. Your partner
The inversion table is intended for home use should be ready to return the backrest to the
only. Do not use the inversion table in any upright position if you cannot complete the
commercial, rental, or institutional setting, rotation.
.Keep the inversion table indoors, away from 15. If you feel pain or dizziness while exercising,
moisture and dust. Do not put the inversion stop immediately and begin cooling down.
table in a garage or covered patio, or near
water. 16. Following is alist of factors and conditions
5. Use the inversion table only on alevel sur-
face. Cover the floor beneath the inversion
table to protect the floor.
6. Make sure that all parts are properly tight-
ened each time the inversion table is used.
Replace any worn parts immediately.
7. Keep children under 12 and pets away from
the inversion table at all times.
8. The inversion table is designed to support a
maximum user weight of 300 Ibs. (136 kg).
Do not use weights with the inversion table.
9. Always wear athletic shoes with laces to help
secure your feet in the inversion table, and
for foot protection while exercising.
10. The inversion table should be used only by
persons 6 ft. 6 in. (198 cm) tall or less.
11. Keep hands and feet away from moving
parts.
12. Always make sure that the ankle lock is
secured snugly against your ankles and that
that may make inverti ng inadvisable (this list
is not exhaustive: it is intended only for refer-
ence), if one or more factors or conditions
apply to you, consult your physician before
using the inversion table.
=Pregnancy
• Hiatal hernia or ventral hernia
=Glaucoma, retinal detachment, or conjunc-
tivitis
=High blood pressure, hypertension, or
recent stroke or transient ischemic attack
=Heart or circulatory disorders for which
you are being treated
-Middle ear infection and extreme obesity
=Spinal injury, cerebral sclerosis, or acutely
swollen joints
• Bone weakness (osteoporosis), recent
unhealed fractures, medullary pins, or sur-
gically implanted orthopedic supports
=The use of anticoagulants, including high
doses of aspirin
17. The decal shown on page 4 has been placed
on the inversion table, if the decal is missing
or illegible, call the toll-free telephone num-
ber on the front cover of this manual and
order a free replacement decal. Apply the
decal in the location shown.
AWARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3

BEFORE YOU BEGIN
Thank you for selecting the NordicTrack ®REVITALIZE
INVERSION SYSTEM inversion table. The inversion
table will increase your intervertebral dimension,
decrease pressure on intervertebral discs, stretch and
relax your muscles, and temporarily relieve back pain
associated with the listed conditions.
For your benefit, read this manual carefully before
using the inversion table. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number is831.14595.0. The serial number can
be found on a decal attached to the inversion table (see
the front cover of this manual).
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.
ASSEMBLED DIMENSIONS:
Height: 62 in. (157 cm)
Width: 36 in. (91 cm)
Depth: 66 in. (168 cm)
Head rest
Handle
Right Frame
Backrest
Short Adjustment Knob
Lock Handle
Long Adjustment Knob
Index Handle
Left Frame
Ankle Brace
Foot Plate
o.:o:o.
Misuse of this machine
may result in serious
injury.
• Read user's manual
prior to use and follow
all warnings and
instructions.
Do not allow children
on or around machine.
- Keep body, clothing,
and hair free and clear
of all moving parts.
• Replace label if
damaged, illegible, or
removed.
4

PART iDENTiFiCATiON CHART
See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST on page 18. Note: Some small parts may have been pre=
assembled, if apart is not in the parts bag, check to see if it has been preassembled.
H
M6 Washer (62) H
MIO Washer (68)
M10 Curved Washer (79)
1
MIO Large Washer (64)
M8 Nylon
Locknut (72)
MIO Nylon
Locknut (65)
MIO x 16mm
Button Screw (54)
M4 x 15mm
Screw (58)
M8 x 16mm
Bolt (61)
M6 x 18mm
Button Screw (55)
M4 x 20mm
Screw (71)
M5 x 25mm
Screw (59)
E-
M4 x 25mm
Screw (60)
c_
M4 x 30mm
Screw (63)
M10 x 35mm
Button Bolt (53)
MIO x 53mm Button Bolt (78) P
M6 x 55mm Button Screw (56)
MIO x 75mm Button Bolt (57)
MIO x 80mm Button Bolt (52)
MIO x 85mm Button Bolt (51)
MIO x 95mm Button Bolt (73)

ASSEMBLY
Make Assembly Easier
Everything in this manual is designed to ensure
that the inversion table can be assembled suc-
cessfully by almost anyone However the inver-
sion table has many parts and the assembl t'
process will take time By setting aside plenty of
time assembly will go smoothly
Before beginning assembly, carefully read the
following information and instructions:
,Because of itsweight and size, the inversion
table should be assembled in the location where
it will be used. Make sure that there is enough
clearance to walk around the inversion table as
you assemble it.
.Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the inversion table, make sure
that all parts are oriented as shown in the
drawings.
• Assembly requires two persons.
° For help identifying small parts, use the PART
IDENTIFICATION CHART on pad
In addition to the included hex key
and grease packets, the following tools (not
included) may be required for assembly:
.two adjustable wrenches
* one rubber mallet
* one standard screwdriver
* one Phillips screwdriver
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Before beginning assembly, make sure
that you understand the information in
the box above, For help identifying small
parts, see page 5,
Attach a Foot (42) to the Left Base (1) with an
M4 x 20mm Screw (71)
Press a 63mm Round Cap (40) onto the Left
Base (1) Next, tighten a Leveling Foot (41)
into the Left Base
Repeat this step for the Right Base (2).
1 2

SlidetheRightBase(2)intotheLeftBase(1).
AttachtheLeftBasetotheRightBasewith
twoM10x80mmButtonBolts(52),fourM10
CurvedWashers(79),andtwoM10Nylon
Locknuts(65).
AttachaFoot(42)totheRightBase(2)with
anM4x20mmScrew(71).
AttachtheSupportLeg(13)totheCenter
Base(3)withthreeM10x35mmButtonBolts
(53)andthreeM10NylonLocknuts(65).
AttachtheBase(14)totheCenterBase(3)
withfourM5x25mmScrews(59).
AttachtheSupportBracket(15)totheSupport
Leg(13)withtwoM4x15mmScrews(58).
79 65
i
i
59,
i
65 59
15
58 f 3
7

Attach the Center Base (3) to the Left and
Right Bases (1,2) with four MIO x 80mm
Button Bolts (52), four MIO Curved Washers
(79), and four MIO Nylon Locknuts (65).
Apply some of the included grease to both
sides of the Left Large Spacer (31).
Attach the Left Frame (4) and the Left Large
Spacer (31) to the Center Frame (7) with a
29mm Spacer (48), an MIO Large Washer
(64), and an MIO Nylon Locknut (65). Then,
press an 89mm Cap (32) into the Center
Frame.
Repeat this step with the Right Frame (5)
and the Right Large Spacer (70).
Attach the Left and Right Frames (4, 5) to the
Left and Right Bases (1,2) with four MIO x
85mm Button Bolts (51) and four MIO Nylon
Locknuts (65).
52 79
65
1\
79
32 65 64
31
7Grease
4_
65
4
65
i
51
51
8

Attach the Top Cover (23) and the Bottom
Cover (24) to the Center Frame (7) with two
M4 x 15mm Screws (58) and an M4 x 30mm
Screw (63).
Attach the Center Frame Extension (6) to the
Center Frame (7) with two M10 x 53mm
Button Bolts (78) and two M10 Nylon Locknuts
(65).
Insert the Headrest Frame (9) into the
Backrest Frame (8). Attach the Headrest
Frame with two M10 x 16mm Button Screws
(54).
10. Apply a small amount of grease to an M10 x
95mm Button Bolt (73).
Pull the Long Adjustment Knob (43) out as far
as it will go. Insert the bracket on the Backrest
Frame (8) into the Top Cover (23). Attach the
Backrest Frame to the Center Frame
Extension (6) with the M10 x 95mm Button
Bolt (73) and an M10 Nylon Locknut (65).
Then, engage the Long Adjustment Knob in
one of the holes in the bracket.
See the inset drawing. Attach an M8 x 16mm
Bolt (61) to the bottom hole in the bracket on
the Backrest Frame (8) with an M8 Nylon
Locknut (72).
10
63
65
72
8 Bracket
23
Grease
9

11. See the inset drawing. Identify the Top Tube
(16) and the Bottom Tube (17). Do not con-
fuse these Tubes with the Ankle Brace
Tube (not shown), which has holes in dif-
ferent locations.
Insert the Top Tube (16) and the Bottom Tube
(17) into the indicated holes in the Leg Frame
(10). Attach each Tube with an M4 x 15mm
Screw (58).
Next, attach the Foot Plate (19) to the Top and
Bottom Tubes (16, 17) with four M4 x 25mm
Screws (60).
12. Insert the Lock Frame (11) into the Foot Plate
(19) while sliding the Lock Frame onto the Leg
Frame (10). Attach the Lock Frame to the Leg
Frame with an MIO x 75mm Button Bolt (57),
two MIO Washers (68), two 16mm Spacers
(46), and an MIO Nylon Locknut (65).
Pull up on the Lock Handle (33) as far as it will
go. Next, position the Lock Frame (11) over
the indicated notch in the Leg Frame (10).
Then, release the Lock Handle to engage the
Lock Frame in the notch.
Insert the Ankle Brace Tube (18) into the Leg
Frame (10) and attach the Ankle Brace Tube
with two M4 x 15mm Screws (58).
13. Identify the two Front Ankle Braces (22), which
do not have holes in the indicated locations.
Slide a Front Ankle Brace onto the round tube
on the Lock Frame (11). Next, press a 19mm
Round Cap (45) into the end of the round
tube, and attach the Round Cap with an M4 x
15mm Screw (58). Attach the other Front
Ankle Brace (22) to the round tube in the
same manner.
Attach an M8 x 16mm Bolt (61) to the Leg
Frame (10) with an M8 Nylon Locknut (72).
See the inset drawing. Slide a Rear Ankle
Brace (80) onto the Ankle Brace Tube (18).
Attach the Rear Ankle Brace with two M4 x
15mm Screws (58). Then, press a 19mm
Round Cap (45) into the end of the Ankle
Brace Tube, and attach the Round Cap with
an M4 x 15mm Screw (58). Attach the other
Rear Ankle Brace (80) to the Ankle Brace
Tube in the same manner.
11
19
12
33
11,
Notch
0
46 57
18
13
45 22
No Holes - _-
18 8O 58
58 %45
10

14. Pull the Short Adjustment Knob (74) out as far
as it will go, and insert the end of the Leg
Frame (10) a few inches into the Backrest
Frame (8).
See the inset drawing. Press the round tab
on the Leg Frame Bushing (38), and press the
Leg Frame Bushing into the Backrest Frame
(8). Make sure that the round tab on the
Leg Frame Bushing snaps into the indicat-
ed hole in the Backrest Frame.
Then, slide the Leg Frame (10) farther into the
Backrest Frame (8), and engage the Short
Adjustment Knob (74) in one of the holes in
the Leg Frame (10).
15. Attach the Headrest (20) to the Headrest
Frame (9) with two M6 x 18mm Button Screws
(55), an M6 x 55mm Button Screw (56), and
three M6 Washers (62).
Attach the Backrest (21) to the Backrest
Frame (8) in the same manner.
16. Attach a Handle (12) to the Left Frame (4) with
two MIO x 80mm Button Bolts (52), two MIO
Curved Washers (79), and two MIO Nylon
Locknuts (65).
Attach the other Handle (12) in the same
manner.
17. Make sure that all parts are properly tight-
ened before you use the inversion table.
The use of all remaining parts will be
explained in ADJUSTMENT on page 12.
14
15
16
11
62
52

ADJUSTMENT
This section explains how to adjust the inversion table. See DEVELOPING A PROGRAM on page 15 for impor-
tant information about how to get the most benefit from the inversion table.
Make sure all parts are properly tightened each time you use the inversion table. Replace any worn parts immedi-
ately. The table can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
SELECTING THE BACKREST FRAME POSiTiON
See the inset drawing. The bracket on the Backrest
Frame (8) has four adjustment holes. The correct hole
to use will depend on the your body weight and the
desired level of responsiveness. See the chart to
determine which hole to use.
To adjust the Backrest Frame (8), pull the Long
Adjustment Knob (43) out as far as itwill go. Move the
Backrest Frame and engage the Long Adjustment
Knob in the desired hole in the bracket on the Backrest
Frame.
Use the inversion table with the Backrest Frame (8)
adjusted to each position to determine which is best
for you.
A B C D
250-300 Ibs. #*
200-250 Ibs. #*
150-200 Ibs. #*
80-150 Ibs. #*
Hole A-- Least responsive
Holes B, C--Moderately responsive
Hole D=Most responsive
#Beginner/partial inversion
*Advanced/full inversion
%///
y/ ,o,o C
v -H°leD
ADJUSTING THE LEG FRAME
The length of the Leg Frame (10) can be adjusted to
correspond to your height. Pull the Short Adjustment
Knob (74) out as far as it will go. Slide the Leg Frame
intoor out of the Backrest Frame (8) so that the first
or second measurement greater than your height is
covered by the Backrest Frame. Then, engage the
Short Adjustment Knob into adjustment holes in the
Leg Frame and the Backrest Frame.
Use the inversion table with the Leg Frame (10)
adjusted to a few different lengths to determine which
length is best for you.
AHL VVAM|_||_U: The inversion table is
designed to be used by persons 6 ft, 6 in, (198
cm) tall orles s,
__. idj_s°tiilt _'_'\/
12

USING THE ANKLE LOCK
To secure your ankles in the inversion table, pull
the Lock Handle (33) out as far as it will go, and
move the Lock Frame (11) away from the Leg
Frame (10). Stand on the Foot Plate (19) with the
backs of your legs against the indicated Ankle
Braces (22). Push the Lock Frame against your
ankles and engage the Lock Handle into a notch in
the Leg Frame.
WAR NING: A waysmakesure
that the Lock Frame (11) is secured snugly
against your ankles before using the inver-
sion table. Always wear athletic shoes with
laces to help secure your feet in the inversion
table.
SETTING THE INVERSION ANGLE
The inversion table can be set to rotate between
15 and 90 degrees in 15 degree increments. To
set the inversion angle, pull the Index Handle (25)
out as far as it will go, and turn the Index Handle
until the arrow on top of the Index Handle points to
the desired degree setting. Then, release the
Index Handle; make sure that the index Handle
is fully engaged.
LEVELING THE INVERSION TABLE
If the inversion table rocks slightly on your floor,
turn one or both of the Leveling Feet (41) until the
exercise cycle is level.
LOCKING THE INVERSION TABLE
To lock the inversion table between usage, insert
the Lock Pin (50) into the Support Leg (13) and
secure the Lock Pin with an MIO Nylon Locknut
(65).
41
11\
Notches
41
Arrow
13

ROTATING ON THE iNVERSiON TABLE
This section explains how to rotate back on the inversion table, and then return to the starting position. Before
using the inversion table, see the ADJUSTMENT section starting on page 12 to correctly set up the
inversion table. It may be helpful to have a second person ready to assist you as you learn to use the inversion
table.
ROTATING BACK ON THE iNVERSION TABLE ROTATING UP ON THE iNVERSION TABLE
To rotate back on the inversion table, slowly lift your
arms over your head until you reach the desired posi-
tion. The speed at which you lift your arms will deter-
mine how quickly the inversion table will rotate. Rest
your arms in a comfortable position that does not
cause the inversion table to rotate. Note: The inversion
table will only rotate to the degree setting set by the
index handle.
To return to the starting position, move your hands
toward your waist until you rotate to a horizontal posi-
tion. Rest in a horizontal position for 30 to 60 seconds
before rotating to the starting position. This will allow
your body to readjust. Return to the starting position
slowly. Dizziness after using the inversion table is an
indicationthat you have returned to the starting position
too quickly.
To rotate up from the fully inverted position, pull your-
self up using the handles.
Do not sit up to return to the starting position.
14

DEVELOPING A PROGRAM
This section contains information and suggestions about using the inversion table. Make sure that all parts are
properly tightened each time you use the inversiontable. Replace any worn parts immediately. See the ADJUST=
MENT section starting on page 12 to identify parts referred to in this section.
BENEFiTiNG FROM USING THE iNVERSiON TABLE iNTERMEDiATE PROGRAM
If you feel nauseated while using the inversion table,
return to the starting position. Note that itmay take a
few weeks of use for your inner ear to become accus-
tom to being inverted.
Do not use the inversion table right after you have
eaten.
Moving while using the inversion table may make ita
more comfortable experience, and may help joints and
muscles stretch and relax. Always move in a slow, con-
trolled manner.
The greater the angle at which the inversion table is
used, the shorter the time that you should rotate back
before rotating up. Increase the amount of inverted time
and the angle of use gradually.
Always pay attention to how your body feels as you use
the inversiontable. Increase the level of intensityonly
as it is comfortable for you. When you feel like you have
had enough, return to the starting position.
BEGINNER PROGRAM
The following are suggestions for persons who are just
starting to use the inversion table.
The following are suggestions for persons who have
become comfortable using the inversion table as
described under the BEGINNER PROGRAM.
Increase the angle to which the inversion table can
rotate, as it is comfortable. Adjust the index handle to
allow the inversion table to rotate to up to 60°, a few
degrees at a time.
Start to do gentle stretching while using the inversion
table.
Gradually increase the amount of time that you use
the inversion table to ten minutes or more, two or
three times a day. Routines can be varied from rotat-
ing back for one or two minutes and then up for 30
seconds, to rotating back and up for equal amounts of
time.
FULL iNVERSiON PROGRAM
The following are suggestions for persons who have
become comfortable using the inversion table as
described under the INTERMEDIATE PROGRAM and
desire to rotate to greater angles. Note that all the
benefits of inversion can be gained by rotating to 60°.
Do not attempt to do sit-ups.
Set the index handle to allow the backrest frame to
rotate to 15° or less for the first one or two weeks. This
will allow your body time to adjust to the change in
gravitational pull.
Increase the angle to which the inversion table can
rotate, as it is comfortable. Adjust the index handle to
allow the inversion table to rotate until it comes in con-
tact with the center frame.
Use the inversion table for one or two minutes at a
time, two or three times a day.
Stay inverted only for as long as it is comfortable. This
may be only a few seconds at first.
Adjust the backrest frame so that the long adjustment
knob is in the top hole (see SELECTING THE BACK-
REST FRAME POSITION on page 12). If you weigh
220 Ibs. (100 kg) or more, adjust the long adjustment
knob to the center hole in the backrest frame. Rotate
back and up as described on page 14.
15

NOTES
16

NOTES
17

PART LiST--Model No. 831.14595.0 RO806A
Key No. Qty. Description Key No. Qty.
1 1 Left Base 43 1
2 1 Right Base 44 2
3 1 Center Base 45 4
4 1 Left Frame 46 2
5 1 Right Frame 47 2
6 1 Center Frame Extension 48 2
7 1 Center Frame 49 1
8 1 Backrest Frame 50 1
9 1 Headrest Frame 51 4
10 1 Leg Frame 52 10
11 1 Lock Frame 53 3
12 2 Handle 54 2
13 1 Support Leg 55 4
14 1 Base 56 2
15 1 Support Bracket 57 1
16 1 Top Tube 58 20
17 1 Bottom Tube 59 4
18 1 Ankle Brace Tube 60 4
19 1 Foot Plate 61 2
20 1 Headrest 62 7
21 1 Backrest 63 1
22 2 Front Ankle Brace 64 2
23 1 Top Cover 65 24
24 1 Bottom Cover 66 1
25 1 Index Handle 67 1
26 1 Index Ring 68 2
27 1 Cup Washer 69 1
28 1 Small Spring 70 1
29 1 Cup Bushing 71 3
30 1 Index Cup 72 2
31 1 Left Large Spacer 73 1
32 3 89mm Cap 74 1
33 1 Lock Handle 75 1
34 1 Stop Cap 76 2
35 1 Lock Rod 77 1
36 1 Lock Spring 78 2
37 1 Lock Wedge 79 12
38 1 Leg Frame Bushing 80 2
39 2 42mm x 70mm Cap # -
40 2 63mm Round Cap # -
41 2 Leveling Foot # -
42 3 Foot
Note: "#" indicates a non-illustrated part. Specifications are subject to change
of this manual for information about ordering replacement parts.
Description
Long Adjustment Knob
32mm Round Cap
19mm Round Cap
16mm Spacer
Pivot Bushing
29mm Spacer
Bumper
Lock Pin
MIO x 85mm Button Bolt
MIO x 80mm Button Bolt
MIO x 35mm Button Bolt
MIO x 16mm Button Screw
M6 x 18mm Button Screw
M6 x 55mm Button Screw
MIO x 75mm Button Bolt
M4 x 15mm Screw
M5 x 25mm Screw
M4 x 25mm Screw
M8 x 16mm Bolt
M6 Washer
M4 x 30mm Screw
MIO Large Washer
MIO Nylon Locknut
M6 x 15mm Screw
MIO Nut
MIO Washer
30mm x 60mm Cap
Right Large Spacer
M4 x 20mm Screw
M8 Nylon Locknut
MIO x 95mm Button Bolt
Short Adjustment Knob
M6 x 60mm Button Bolt
M5 x 15mm Screw
M6 Nut
MIO x 53mm Button Bolt
MIO Curved Washer
Rear Ankle Brace
User's Manual
Hex Key
Grease Packet
without notice. See the back cover
18

EXPLODED DRAWING--iVlodei No. 831.14595.0 Roso6A
33_, 69
34_,
45
22 .58
65 68_,
46 57
22 45
F
44
79
8O
39
58 58 62 56
12
40
52
52
/ /
6O
8O 58
45 56
;32 48
79
65
79
.52
,4 62
65
65
J
79
19

ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
the MODEL NUMBER of the product (831.1 4595.0)
• the NAME of the product (NordicTrack REVITALIZE INVERSION SYSTEM inversion table)
the SERIAL NUMBER of the product (see the front cover of this manual)
the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on
pages 18 and 19)
LIMITED WARRANTY
WHAT IS COVERED--The entire NordicTrack _>REVITALIZE INVERSION SYSTEM inversion table ("Product") is warranted to be
free of all defects in material and workmanship.
WHO IS COVERED--The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED--ICON Health & Fitness, Inc. ("ICON") warrants the product for 90 days after the date of purchase.
Labor is covered for 90 days.
WHAT WE DO TO CORRECT COVERED DEFECTS--We will ship to you, without charge, any replacement part or component, pro-
viding the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our
option, we will replace the Product.
WHAT IS NOT COVERED--Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper
assembly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and
maintain as set out in your User's Manual ("Manual").
WHAT YOU MUST DO--Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as spec-
ified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instruct-
ed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER'S MANUAL--It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the
periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICE--Simply call our Customer Service Department at 1-888-825-2588 and tell them your name
and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for serv-
ice where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return
Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping car-
ton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or prob-
lem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or per-
formance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoy-
ment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness
for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.
ICON HEALTH &FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 244719 R0806A Printed in China © 2006 ICON IP, Inc.