Nortel Enterprise Edge M7310N Parts list manual

© 2000 Nortel Networks
P0908519 Issue 02
Enterprise Edge
M7310N
User Card

Page 1 Enterprise Edge M7310N User Card
Your Enterprise Edge M7310N Telephone
Using Button
Inquiry Check what is programmed on your memory buttons. 1. Release all calls or lines with dial tone.
2. Press ƒ•‚.
3. Press the button(s) that you want to check and read the display.
4. Press ƒwhen finished.
Adjusting display
contrast 1. Press ƒ•‡. 2. Press UP or DOWN for the level you want.
3. Press OK when finished.
Selecting a ring
type and volume
level
1. Press ĥfl.
2. Press ⁄, ¤, ‹, ›, or NEXT to hear the different ring types.
3. While the telephone is ringing, press √to adjust the
volume level.
4. Press OKto store the volume level and ring.
Using display
buttons Three display buttons appear directly below the display. When they are active, these
buttons are labelled in capital letters on the
bottom line of the display. In Enterprise Edge
documents, display buttons are shown as
underlined, capital letters: for example, OK.
is used to access the top function of a dual memory button
shows the time, date, and call information; guides you while
Display buttons
Release button
Hold button
Dial pad
Feature button
Volume control
Memory buttons
Dual memory button
Indicators
Shift button
Display

Page 2 Enterprise Edge M7310N User Card
Making and answering calls
Answering calls Answering calls using the handset
When your telephone rings, or ºflashes beside an Intercom or line button:
1. Lift the handset.
OR
Press the button beside the flashing ºbefore lifting the handset.
Answering calls using Handsfree
When your telephone rings, or ºflashes beside an Intercom or line button:
1. Press ©.
Making calls Depending upon the dialing mode programmed on your telephone, you may
have to lift the handset before making a call.
¬External calls using numbered line buttons
1. If you do not have an external Prime line, press a line button.
2. Dial your call.
∆External calls using Intercom buttons
1. Lift the handset.
2. If ºappears beside an Intercom button, enter a line pool access code.
OR
Press an Intercom button without º, then enter a line pool access code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press ∆.
2. Dial your call.
Note: Line pool access codes and extension numbers are supplied by
your System Administrator.
Making calls using Handsfree
1. Press ©instead of lifting the handset.
˙Holding Calls
1. Press ˙.The ºflashes beside the line on hold.
2. Press the line button with the flashing ºto return to the call.
Automatic hold
Calls are put on hold automatically when you switch from one line to another.
Exclusive hold
Use Exclusive Hold (ƒ˙) to keep a call on hold so that it can be
retrieved only at your telephone.
©System Administrator can program Handsfree for your telephone.
Switching between Handsfree and handset
1. Press ©and replace the handset to switch to Handsfree.
2. Pick up the handset to switch back.
Using Mute
1. Press ©microphone OFF.
2. Press ©again to turn the microphone ON.

Page 3 Enterprise Edge M7310N User Card
Remember: Press ƒ•‚ to check a memory or line button.
Notice These telephones now conform to the latest standards in relation to the
positioning of Q and Z on the number buttons. The Q appears on button
number 7 and the Z appears on button number 9.
Programming
memory buttons External Autodial 1. If you are ona call oran open line
with dial tone, press
˙or ®.
2. Press ƒ•⁄.
3. Press a memory button.
4. Dial the external number.
5. Press OK to store the number.
6. Label your new button.
Internal Autodial
1. If you are on a call or an open line with
dial tone, press
˙or ®.
2. Press ƒ•¤.
3. Press a memory button.
4. Dial the station number.
5. Label your new button.
Features
1. If you are ona call oran open line
with dial tone, press
˙or ®.
2. Press ƒ•‹.
3. Press a memory button.
4. Press ƒand the feature
code.
5. Label your new button.
Erasing memory buttons
1. If you are on a call or an open line with
dial tone, press
˙or ®.
2. Press ƒ•⁄.
3. Press the memory button you want to
erase.
4. Press OK to erase the button.
About memory buttons
Programming memory buttons
Memory buttons store telephone
numbers or feature codes to give
you one-touch dialling or
feature activation.
To use the top function, press
the shift button, then press the
dual-memory button.
There are two types of memory
buttons: single-memory and
dual-memory.
Dual-memory buttons:
To use the bottom function,
press the dual-memory button.
Single-memory buttons:
Single-memory buttons are the
buttons with indicators other
than line or Handsfree buttons.

Page 4 Enterprise Edge M7310N User Card
Setting up the telephone
Connecting the cords ATTENTION Before attempting to carry
out any work on the telephone, ensure that
the line cord is unplugged from the wall
socket.
To remove any of the cords, squeeze the
release latch on the plug and gently pull
the plug from the socket.
Connect the handset cord to the jack
labelled with the telephone icon and route
the cord as shown.
If you are using a headset, route the cord
along the channel in the base and connect
the cord to the telephone jack that is
marked with the headset icon.
Route the line cord through the stand and
connect the cord to the telephone jack that
is marked with the jack icon.
Attach the stand using either pair of slots;
to raise the back of the telephone to its
highest position, use these slots.
Once the above work is complete,plug the
line cord back into its wall socket.
Press here to
remove the stand.
1
Press here firmly
until it clicks, to
attach the stand.
2

Page 5 Enterprise Edge M7310N User Card P0908519 Issue 02
12 cm
Setting up the telephone
Mounting the
telephone on
the wall