NuAire DRI-ECO-RH User manual

1
04. 08. 21. Document Number 671793Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA |nuaire.co.uk
DRI-ECO-RH
Humidity Sensor For Use With RF
Enabled Hall Control DRI-ECO Units
Installation Manual
EMC Directive
2014/30/EU
LVD Directive
2014/35/EU
1.0 SAFETY INFORMATION
• This appliance should not be used by children or persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the safe use of the appliance by a person responsible for their safety.
Children shall not play with the appliance. Cleaning and user maintenance shall not be carried
out by children.
1.1 Hazard Symbols
GENERAL WARNING
Signifies a general warning regarding hazard specified by supplementary information.
REFER TO INSTRUCTION MANUAL
Read and understand the installation and maintenance manual before installing,
operating or maintaining this product.
1.2 Important Information
This manual contains important information on the safe and
appropriate assembly, transport, commissioning, operation,
maintenance, disassembly and simple troubleshooting of the product.
While the product has been manufactured according to the accepted
rules of current technology, there is still a danger of personal injury or
damage to equipment if the following general safety instructions and
the warnings contained in these instructions are not complied with.
•Read these instructions completely and thoroughly before
working with the product.
•Keep these instructions in a location where they are accessible
to all users at all times.
•Always include the operating instructions when you pass the
product on to third parties.
1.3 Personal Protective Equipment
The following minimum Personal Protective Equipment (PPE) is
recommended when interacting with Nuaire product:
•Protective Steel Toed Shoes - when handling heavy objects.
•Full Finger Gloves (Marigold PU800 or equivalent) - when
handling sheet metal components.
•Semi Fingerless Gloves (Marigold PU3000 3DO or equivalent)
- when conducting light work on the unit requiring tactile
dexterity.
•Safety Glasses - when conducting any cleaning/cutting operation
or exchanging filters.
•Reusable Half Mask Respirators - when replacing filters which
have been in contact with normal room or environmental air.
Nuaire would always recommend a site specific risk assessment by a
competent person to determine if any additional PPE is required.
2.0 INSTALLATION
Installation must be completed by competent persons, in accordance
with good industry practice and should conform to all governing and
statutory bodies i.e. IEE, CIBSE, etc.
The sensors and switches include an LED which illuminates when a
button is pressed. A green light shows that communication between
the sensor or switch and the fan unit is taking place. A red light shows
that no communication is taking place and binding may be required.
1 DRI-ECO-RH
Indent
Button

2
04. 08. 21. Document Number 671793Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA |nuaire.co.uk
DRI-ECO-RHInstallation Manual
2.1 Binding Unit To Sensor
2.1.1 Unit Binding Mode
Where a Humidity sensor is present, it must first be bound to the fan
unit before it can work. In order to bind the sensor(s) the fan must be
in binding mode. The steps required to enter binding mode are shown
below.
•Ensure the fan unit is powered on.
•Unit will enter the start-up sequence for 2 minutes when first
powered on. Press the down button on the ceiling diffuser control
panel once, to exit the start-up sequence.
•Press and hold the both the UP and DOWN buttons for 20-30
seconds then release. A single horizontal bar on the display flashes.
•Press "down" to enter binding mode (binding mode lasts for 5
minutes).The unit will now display a flashing ‘b’ to indicate it has
entered binding mode.
A solid “P” indicates purge, a solid “b” indicates boost, and a
flashing “b” indicates binding mode.
DOWNUP
DOWNUP
2 Drimaster Diffuser Control
2.1.2 Binding Sensor
Putting the unit into binding mode (Section 2.1) before powering the
sensors will automatically bind the sensors to the unit. However if they
do not bind follow the below steps.
•Put the unit into binding mode.
•Power up sensors (insert batteries for humidity, mains for CO2).
•Tap indented button then hold until left hand LED flashes red/
green (ignore red/blue and continue to hold). Release button
whilst flashing.
•Tap indented button again, whilst red/green LED is still flashing.
•Close binding window on fan control panel by holding both “up”
and “down” for 5 seconds and release.
•Check sensor has bound by tapping indented button and look for
left hand LED to go green. If it displays red, repeat from step 1.
2.2 RF Frequency
RF enabled DRI-ECO devices operate at a frequency of 868.3 MHz.
3.0 CONTROLS
3.1 Sensor Setpoint
The sensors will automatically trigger the fan to increase speed once
the sensor set point has been exceeded. To change the sensor set point,
press and hold the indent button until the status indication LED flashes
BLUE/RED then release, the green LED’s illuminate to show the current
sensor set point. Press the button to cycle through all allowed values,
and press and hold to confirm choice. If the button is not operated for
10 seconds the set point currently selected is stored.
Boost (Sensor) - If a sensor set point has been exceeded, the unit will
enter boost mode and a solid ‘b’ will be shown in the display. Boost
mode increases the speed setting by 1. If the unit is running at speed
6, boost is ignored (i.e. A unit is running at speed 3. A boost signal is
received from a sensor whereby the speed changes to 4. When the
boost condition clears, the unit will revert to speed 3).
3.2 LED Indicators
The sensors and switches include an LED which illuminates when a
button is pressed. A green light shows that communication between
the sensor or switch and the fan unit is taking place. A red light shows
that no communication is taking place and binding may be required.
4.0 MAINTENANCE
It is important that maintenance checks are recorded and that the
schedule is always adhered to, in all cases, the previous report should
be referred to.
4.1 Routine Maintenance
This sensor can be cleaned with a dry brush or dry cloth. Any other
maintenance or cleaning should be carried out by properly qualified
personnel.
Ensure the unit does not come into contact with any kind of liquid
or solvent. If this should occur, contact a qualified technician before
reassembling the fan.
5.0 WARRANTY
The 7 year warranty starts from the day of delivery and includes parts
and labour for the first year. The remaining period covers replacement
parts only.
This warranty is void if the equipment is modified without
authorisation, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the details
contained in this manual and general good practice.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Conditions of Sale. Customers purchasing from
outside of the UK should contact Nuaire International Sales office for
further details.
Failure to maintain the unit as recommended will invalidate the
warranty.

3
04. 08. 21. Document Number 671793Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA |nuaire.co.uk
DRI-ECO-RHInstallation Manual
6.0 END-OF-LIFE AND RECYCLING
Where possible Nuaire use components which can be largely recycled
when the product reaches its end-of-life:
•Fans, motors, controls, actuators, cabling and other electrical
components can be segregated into WEEE recycling streams.
•Sheet metal parts, aluminium extrusion, heating/cooling coils and
other metallic items can be segregated and fully recycled.
•EPP, plastic ducting, nylon corner pieces, plastic heat exchangers,
packaging material and other plastic components can be
segregated into mixed plastic and widely recycled.
•Cardboard packaging, wood, used filters and other paper
components can be largely recycled or fully processed in energy
from waste centres.
•Remaining Items can be further segregated and processed in
accordance with the zero waste hierarchy. Please call After Sales
Support for further information on items not listed above.
Ensure that Nuaire product is made safe from any electrical / water
/ refrigerant supplies before dismantling commences. This work
should only be undertaken by a qualified person in accordance with
local authority regulations and guidelines, taking into account all
site based risks.
7.0 AFTER SALES AND REPLACEMENT PARTS
For technical assistance or further product information, including spare
parts and replacement components, please contact the After Sales
Department.
If ordering spares please quote the serial number of the unit together
with the part number, if the part number is not known please give a full
description of the part required. The serial number will be found on the
identification plate attached to the unit casing.
Telephone [phone]
[e-mail]

4
04. 08. 21. Document Number 671793Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA |nuaire.co.uk
DRI-ECO-RHInstallation Manual
NOTES