Olimpia splendid DOLCECLIMA FRESCO 12AC WI-FI User manual

DOLCECLIMA FRESCO
12AC & 15AC WI-FI
Models: 2261 & 2262
Wi-Fi Setup Quick Start Guide
OS Home

Make sure your mobile phone or tablet is connected to the
internet before proceeding with user registration.
Open OS Home App
1. Click on “Sign Up”. (Fig. 1)
2. Enter your E-mail, check “I Agree” box, then click on “Get Verification
Code”.
3. Enter the verification code sent to the email you previously used to
register. If email still hasn’t arrived, click on “Didn’t get a code?” to
resend. (Fig. 2)
4. Set your desired password, click “Done”.
Figure 1 Figure 2
1. Tap the icon on
Android device.
2. Type OS Home in the search window
and search for the app.
3. Tap the INSTALL button.
4. Tap the ACCEPT button on the App
permissions screen.
5. When the app is finished installing, an
OPEN button is displayed on the screen.
If you are ready to begin registration, tap
OPEN and the app will start.
Android DevicesiOS Devices
1. Tap the icon on your Apple device.
2. Type OS Home in the search window
and search for the app.
3. Tap INSTALL button. If asked, enter your
Apple iTunes® password, and then tap
OK to proceed.
4. When the app is finished installing, an
OPEN button is displayed on the screen.
If you are ready to begin registration, tap
OPEN to launch the app.
Install OS Home App for iOS or Android
1Register an account with OS Home App 2
If the email with the code does not arrive, check your “Spam”
folder in your mailbox.

Make sure your mobile device is connected to the same Wi-Fi
network you want to use to connect the FRESCO portable AC.
1. “Log-in” to the OS Home app using previously setup email and password,
then agree to Privacy Policy and User’s Agreement. (Fig. 3)
2. Choose device to add in OS Home App
1) Click on “Add Device” or “+” in the top right-hand corner. (Fig. 4)
2) Select “Dolceclima Fresco”. (Fig. 5)
Figure 3 Figure 4 Figure 5
Activate/reset WiFi function using FRESCO touch panel display
3
Connect the power cord of the appliance to the power socket;
then turn on WiFi function for network configuration.
Activate or reset the WiFi function by pressing & holding Fan/Wifi Mode
(SW6) button for approximately 5 seconds until the LED (S10) starts to
blink. (User’s Manual sec. 3.12)
Follow step-by-step directions on the OS Home App to connect
to FRESCO for network setup.
S10
SW6
Please connect using 2.4GHz network. To set router to 2.4GHz, please click
on “Common router setting method” in the following step to select
network and provide password.
Connecting FRESCO to your network using OS Home App
4

3. Confirm network and enter network password then “Next”. (Fig. 6)
4. Confirm that Wifi indicator (S10) on the Fresco touch panel is
on and blinking rapidly.
5. Click on “Confirm indicator rapidly blink”, then click “Next”. (Fig. 7)
6. OS Home connects & configures Fresco Wifi air conditioner. (Fig. 8)
Figure 6 Figure 7 Figure 8
Connecting FRESCO to your network using OS Home App
4
S10
If resetting is necessary, refer to step on previous page to
perform a reset for the FRESCO. 3
Connecting FRESCO using OS Home App –Alternate Method
4A
If unable to add FRESCO to OS Home App, follow directions
below to connect using “AP Mode” option.
Do not cycle power by unplugging power cord from outlet.
1. Reset Wifi indicator (S10) to blink slowly by pressing & holding
Fan/Wifi Mode (SW6) button for approximately 5 seconds.
2. Switch to “AP Mode” by tapping upper right corner. (Fig. 9)
3. Click on “Confirm indicator slowly blink”, then click “Next” (Fig. 10)
Figure 9 Figure 10
SW6
S10
When the FRESCO is connected to the WiFi network, the Wifi indicator
(S10) stops blinking and remains switched ON steadily on the display.
Fresco will be listed in OS Home app under “All Devices”

4. Click “Go to Connect” to be directed to mobile device’s Wifi settings. (Fig. 11)
5. Select FRESCO network name “Smartlife-XXXX” in mobile device Wifi settings.
6. Select “Connect only this time” if prompted (Android only). (Fig. 12)
Figure 11 Figure 12
Connecting FRESCO using OS Home App –Alternate Method
4A Connecting FRESCO using OS Home App –Alternate Method 4A
7. Return to OS Home App to finish setup;
For iOS Device
Click back to “< OS Home”.
For Android Device
1) Click “< Wi-Fi“ back button, then
2) Click “< Connections“ back button, then
3) From open app screen select “OS Home App”.
Smartlife-XXXX
Smartlife-XXXX
When the FRESCO is connected to the WiFi network, the Wifi function LED
(S10) stops blinking and remains switched ON steadily on the display.
OS Home