Oneida Air Systems 10 HP User manual

10 HP NYB Pulley/Belt Drive
Cyclonic
Dust Collectors
Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204
Phone [phone] 476 5151 Fax [phone] www.oneida air.com
Owners Manual

Thank You for Choosing an Oneida Air Systems Product!
OAS manufactures and sells dust collection equipment only. Our qualified technicians and
sales staff are available 7:30am - 6:00pm ST Mon. - Thur. and 7:30am - 5:00pm ST Fri. to
answer any questions concerning OAS products and dust collection. Call for ductwork design
and ductwork quotes, including system pricing and shipping cost.
Read the entire Owners Manual efore installing or operating system!
Proudly
Made in
the U.S.A.
Table of Contents
Page
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
XI.
XII.
XIII.
XIV.
XV.
XVI.
2
3
4
5 - 7
8
9 - 10
11
12
13 - 14
15
16
17
18
19
20
21 - 23
System Start-Up Information
Pulley Drive Configurations
General Specifications & Fan Performance Curves
Dimensions
Configuration xamples
General Assembly Instructions
xternal Filter Box Assembly
Wire Diagram
Fan / Blower Maintenance
Accessories
Troubleshooting
Fire Hazards - Read Before Installing System
Terms and Conditions
Filter Cleaning Instructions
Optional Filter fficiency Gauge Mounting Instructions
Supplemental Instructions for Magnetic Motor Starters
1
O.A.S. 2007
c
10 HP Pulley Drive Owners Manual

O.A.S. 2007
c
10 HP Pulley Drive Owners Manual
I. Syste Start-Up Infor ation
1. Read the installation and maintenance instructions as well as the recommended
safety practices in this manual.
2. Install Ductwork completely:
A.) Seal ductwork with silicone sealant or duct tape.
B.) Have Dust Bin in place and sealed.
3. Have licensed electrician wire Fan / Blower according to wire diagram in this
owners manual.
4. Have licensed electrician check current draw on motor with all gates open. Current
draw should not exceed maximum motor amperage. (OAS is not responsible for
destroyed motors caused by improper wiring or improper installation.)
Caution
The Dust Collector & Fan/Blower are heavy. Handling and
installation should always be performed by experienced and
trained personnel who have experience with rotary equipment.
In addition to the following instructional manual, care should
be taken to ensure compliance with specific safety
requirements mandated by federal, state and local codes.
Warning
Do not operate Fan / Blower without connecting dustbin.
Never operate Fan/Blower without belt and shaft guard in
place. Keep clear of exhaust. Keep hands and objects clear
of inlet and outlet.
Warning
Check amperage draw during operation with all blast gates
open. Make certain amperage is not outside operating limit
indicated on motor plate! If amperage is too high shut down
immediately! (See Troubleshooting section.)
2

II. 10hp Pulley Drive Configurations
1. No Filter - Vent Outside -
Caution:
If exhaust air is vented outside you must provide make up /
return air.
Flue gases (carbon monoxide) can be drawn into the shop from
furnaces, water heaters or other appliances.
1. No
Filter
2. External
Cartridge
Filters
3. External
Tu e
Filters
O.A.S. 2007
c
10HP Pulley Drive Owners Manual
5 gal. dust buckets not included. 3
10hp has 3 cartridges
10hp has
10 tubes
2 rows of 5

III. General Specifications & Fan Perfor ance Curves
4
10hp Fan Curves
O.A.S. 2007
c
10 HP Industrial Systems Owners Manual
Full welded exterior
Main body, cone and inlet: 16 ga. galv.
Flanged 12 dia. Inlet; Flanged 13 dia. Outlet
80 high
14 rolled steel flange discharge
36 dia. rolled steel flange for mounting
Cyclone C-3500
10hp Fan / Blower
Made in USA NYB 224 DH Arrangement 10
10 horsepower, Pulley drive with weather/shaft guard
T CO - Westinghouse T FC 60 Hz 10hp Motor
Three Phase: 230/460v 24/12A (Usable on 208v 25.9 A)
Fan Wheel Dia.: 22.625
3300 CFM @ 12 Static Pressure
System Packages Include:
Angle Iron Wall Mount Brackets
Angle Iron Stand
Plenum Box - 10 or 14 hole ring thimble plenum box to hold Tube Filters.
S lencer - For fan / blower outlet to 13 I.D., will reduce noise level.
Magnet c Motor Starters
Rotary A r-Loc
Optional Items:
This fan has moving parts that can cause
serious injury. Read the installation and
maintenance instructions and the AMCA Safety
Practices manual before starting maintenance
or operating.
1. Keep body, hands and objects away from
the inlet, outlet and other moving parts of the
fan such as belts, pulleys and shafts.
During Operation
2. Do not operate at excessive speeds or
temperatures.
Before starting maintenance work:
Lock power supply in off position and
immobilize fan wheel.
WARNING!
Exter or Cartr dge F lters
10hp - 3 Cartridges - 390 Sq. Ft.
Spun-Bonded Polyester BIA ZH1/487 Test - Rated C
Captures 99.99% of test material over 20 microns
Captures 99.9% of test material between 0.2 - 2.0
microns @ 11 fpm face velocity
Filter Media
Exter or Tube F lters
10hp - 10 Tube Filters
Needle Felted Media BIA ZH1/487 Test - Rated G
Captures 99.99% of test material over 20 microns
Captures 99.5% of test material between 0.2 - 2.0
microns @ 11 fpm face velocity
55 Gal. Steel Drum
Other large dust bins available
Dust Bins
Static pressure and volume together determine
a fans performance. Several factors, such as
layout of ductwork and diameter of openings,
can affect a fans performance.
Performance -
Horsepower -
5.0
2.5
0.0
Fan Static Pressure (In. Wg.)
10hp Performance Curve
0 1000 2000 3000 4000 5000 6000 7000 8000
7.5
10.0
12.5
9000
0
2.5
5
7.5
10
12
15
17
20
22
Fan Input Power (bhp)
Volume Flow Rate (CFM)

IV. Di ensions
5
O.A.S. 2007
c
10 HP Pulley Drive Owners Manual
Top V ew D mens ons - Largest Conf gurat on
1 1/2 Flange w/ Bolt Holes
34
10hp - 229
14
10hp - 83
30
42
17
80
Approx.
18
36
1439
36
8
39
32.5
55 Gal.
42
10
12
8
10hp - 10 tube - 83
5 Gal. Dust Buckets Not Included.
They can be bought separately.
- xternal Tube Filters
32.534
29 1/8
12

IV. Di ensions
6
O.A.S. 2007
c
10 HP Pulley Drive Owners Manual
- xternal Cartridge Filters
17
80
Approx.
18
36
10
14
1439
10hp - 3 filters -Single Row - 66
36
29 1/8
8
39
62
12
55 Gal. 60
Top V ew D mens ons - Largest Conf gurat on
34
10hp - 212
14
10hp - 22
1 1/2 Flange w/ Bolt Holes
42 10hp - 3 filters -Single Row - 66
34
Silencer easily drops
into Filter. Hold filter
up to Flange Plate
and clamp.

7
O.A.S. 2007
c
10HP Pulley Drive Owners Manual
C-3500 Cyclone Stand -
Anchor Feet Securely
to Floor to Prevent
Tipping
(4) 3/8-16 x 1 bolts for Cyclone mount
(20) 3/8-16 x 1 bolts for Cross Brace mount
(28) 3/8-16 x 1 bolts for Triangle Brackets
(48) 3/8 flat Washers
(48) 3/8 serrated Nuts
Un t should be sh pped w th:
w/ 55 Gal. Drum - Part # STZ350055
Choose Mount
Holes to Orient
Inlet in Desired
Location
Inlet
Outlet

V. Configuration Exa ples
Sleeve K t - Sleeve-Kit 14 for C-2500
cyclone requires 16 - 18 for a single
drum and 24 for 2x drums. Additional
feet of flex can be purchased to make
the sleeve kit longer if needed.
Drum - Standard 55 gal. steel drums
are usually 35 - 36 high Oneida Air
sells 55 gal. and 35 gal. fiber and steel
barrels with metal lids and snap on
rings.
55 gal. fiber - 35.5 high 22 dia.
35 gal. fiber - 23 high 22 dia.
55 gal. steel - 35.5 high 22 dia.
Rotary A r Locks - Provide an
alternative to an air tight dust bin for
larger volume capacity and less
maintenance. The airlock maintains an
air tight seal which allows material to
drop out into an open container.
A 10 Airlock will drop 1.85 cu. ft. / rev.
of material.
Plenum inside
Flex
Hose
Metal
Drum
Rotary
Air
Lock
O.A.S. 2007
c
10 HP Pulley Drive Owners Manual
Cyclone wall
mounted with
angle iron
brackets
Cyclone -
Fan/Blower outside
Hoppers - see Accessories page
Dust Box - Can be any height. For
efficient pre-separation there must be
an air tight seal between cyclone and
dust bin.
Air Tight Dust Bins can be used as support for cyclone as well as provide large
capacity dust storage.
xternal
Cartridge
Filter
6, 8,
or 10
Tube
Filters
5 Gal.
Buckets
Fan / Blower
Stand
Splitter
Kit
(2) 55 Gal.
Drums
Cyclone Fan/Blower and f lters can
be placed n d fferent locat ons.
8

VI. General Asse bly Instructions
9
O.A.S. 2007
c
10 HP Pulley Drive Owners Manual
1. Determine mounting height for the cyclone.
- Height depends on size of Dust Bin and length
of Flex Hose to Dust Bin connection.
2. Mount Angle Iron Brackets to wall using included
hardware.
3. Mount Cyclone Barrel to Wall Brackets.
- Determine inlet orientation. Fasten Cyclone to
Brackets with one bolt on each side. Drill new
hole in ring if needed for your orientation.
6. Connect Cyclone Cone to Barrel using included
Clamp Ring.
- Seal around Clamp Ring with silicone.
7. Connect 14 to 10 Reducer to bottom of Cone.
8. Connect Sleeve Kit to Cyclone Cone and Dust Barrel
using included Band Clamps.
For cyclonic preseparation there must be an air
tight seal between cyclone and dust container.
Dust bin must be located vertically under cyclone.
Material drops down by gravity.
Inlet
Cyclone
Barrel
Angle Iron
Wall Brackets
Clamp
Ring
Cyclone
Cone
14 to 10
Reducer
Sleeve
Kit
55 Gal.
Steel
Drum
- Seal around Reducer with silicone.
Ideas for make your own Dust B ns:
- 55 gal. drum, metal or rigid plastic garbage can,
air-tight plywood box.
Note: You can make a lid using plywood lined with some
type of gasket material (Carpet Foam). (Continued on next page.)
4. Lower V - Tube into Cyclone Barrel
5. Connect Outlet Cyclone Barrel to Inlet Cyclone
Barrel using included Clamp Ring.
V - Tube
Outlet
Cyclone
Barrel
Clamp
Ring