Oneida Air Systems Pro 2000 User manual

Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204
Phone [phone] 476 5151 Fax [phone] www.oneida air.com
Shown with optional
bolt together Angle Iron
stand and optional 55
gal. steel drum.
*Models may
vary sligthly in
appearance.
- Baldor
Dust Collector

1
Thank You for Choosing an Oneida Air Systems Product!
AS manufactures and sells dust collection equipment only. ur qualified technicians and
sales staff are available 7:30am - 6:00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to
answer any questions concerning AS products and dust collection. Call for ductwork design
and ductwork quotes, including system pricing and shipping cost.
Table of Contents
Page
Read the entire Owners Manual efore installing or operating system!
Pro 2000 Owners Manual O.A.S. 2007
c
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
XI.
XII.
XIII.
XIV.
XV.
XVI.
XVII.
XVIII.
XVIV.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
System Start-Up Information
Commercial Configurations
General Specifications & Fan Performance Curves
Dimensions
General Assembly
General Assembly Instructions
Bracket Assembly
Filter Assembly
Filter Maintenance
Filter Efficiency Gauge Mounting Instructions
Directions for Cleaning External Filter
Fan / Blower Wiring Diagram
Troubleshooting
Fire Hazards - Read Before Installing System
Terms and Conditions
Stand Assembly
Accessories
Fan Motor Maintenance
Remote Wiring Diagram

2
I. System Start-Up Information
1. Read the installation and maintenance instructions as well as the recommended
safety practices in this manual.
2. Install Ductwork completely before operating collector:
A.) Seal ductwork with silicone sealant or duct tape.
B.) Have Dust Bin in place and sealed.
3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 13
in this owners manual.
4. Have licensed electrician check current draw on motor with all gates open. Current
draw should not exceed maximum motor amperage. ( AS is not responsible for
damage to motors caused by improper installation, wiring or failure to follow these
directions.)
Caution
The Direct Drive Fan / Blower makes the system top heavy!
Use extreme care when setting the unit up!
Warning
If amperage is too high shut down immediately!
(See troubleshooting section.)
Warning
Do not operate Fan / Blower unless Cyclone and Dust Bin
are in place. Motor will over heat!
Warning
Check amperage draw during operation with all blast gates
open. Make certain amperage is not outside operating limit
indicated on motor plate!
Pro 2000 Owners Manual O.A.S. 2007
c

3
II. Pro Series 2000 Configurations
Caution:
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters or other appliances.
1. External Cartridge Filter -
Silencer Included with Filter
Pro 2000 Owners Manual
Silencer
included
w/ Filter
O.A.S. 2007
c
Shown with optional
Angle Iron Stand
and optional 55 gal.
steel drum.
Cartridge Filter Media
1 Pleated Spun-Bonded Cartridge Filter 62 / 130 Sq. Ft.
Accredited, independent lab tested.
Bathed in teflon-like coating for easy dust release.
Captures 99.9% of Test Material from 0.2 - 2 microns.
Kit Contents
8 Ft. Hose and Connection
0
1234
5
INCHES W.C.
Gauge Bracket
Included Square-to-Round Inlet
Included Filter Efficiency Gauge
Included Magnetic Starter
Included
all Bracket
Included Silencer
Do Not Remove

III. General Specifications & Fan Performance Curves
Pro 2000 Owners Manual O.A.S. 2007
c
4
Static pressure and volume together determine
a fans performance. Several factors, such as
layout of ductwork and diameter of openings,
can affect a fans performance.
1973 CFM @ 2 SP w/c w/o filter
Full 16 gauge galvanized cyclone & 14 ga. barrel
Rectangular inlet with included Square to Round to 8
Rectangular outlet
Cast aluminum fan wheel
back inclined non-sparking, non-ferrous dynamic, two-planed balanced to IS 6.3
specifications.
Sound 80 - 82dB @ 10 with Built-in Silencer and Filter
130 Sq. Ft. Filter Media / Spun-Bonded
System Fan Curve
U.S. Made Baldor / TEFC / Class F / 1.15 SF
Single Phase
5hp Motor
208 - 230V
19.8A
Three Phase
5hp Motor
208 - 230 / 460V
13.6 - 12.4 / 6.2A
Pro Series 2000
6
4
2
0
Static Pressure at Cyclone Inlet
CFM
0 200 400 600 1000800
12
18001600
1200
12
8
10
1400 2000
11.1
10
8.1
5.8
4
2.75
2
Without Filter
*Fan curves vary slightly with different filter packages.
With Filter
1973
1802
1709
1543
1273
987
736
0
2.00
2.75
4.00
5.80
8.10
10.00
11.10
12.00
SP @
Inlet
CFM
w/o Filter

5
IV. Dimensions
For Minimum Mounting Heights w/ 62 Filter.
*Dimensions subject to slight variation in manufacturing.
Pro 2000 Owners Manual O.A.S. 2007
c
00.00
72.00
81.00
35 Gal Shown
Add 8"for 55 Gal
62.00
4.00
8.00
18.00
18.00
27.00
53.00
60.00
1
Dimensions shown with
5" flex hose between
drum and one ollars
8.00
16.00

V. General Assembly
Pro 2000 Owners Manual O.A.S. 2007
c
6
Cyclone
Barrel
Cone
Square to Round
Connects to Inlet
1. Motor/Blower Assembly BXI012309-1ph - - 3ph
1a. Fan heel - B X159800
Magnetic Starter w/ Remote Option: 1 phase
1b. Motor Starter - AMR221417 1phase only
1c. Cord Connector - C027063 1 phase only
1d. Cord Connector Locknut - CN340000 1 phase only
1e. 5hp Motor BMZ050170 - 1 ph / BMZ050370-3 ph
1f. Motor Plate - RMP002301
Magnetic Starter not factory wired 3 phase
Enclosed contactor with 220v coil - AMC183600
Overload 12-18 amps - AMO121800
Start Stop Push Button - AMP000000
2. Fan Housing - BHX030009
3. Cyclone Barrel - SXI002309
4. Cyclone Cone - SCX002309
5. Plenum Assembly for Filter 8 Elbow - FPX010300
5a. Thumb Nut (4) - AFT000001
5b. Cartridge Filter Threaded Clamp (4) - AFX000000
5b1. AFB155180 Bolt 5/16-18 x 2 1/2
5c. Fender asher 5/16 (4) - AF 170000
5d. Dust Pan 4 - FPZ016040
5e. Hardware Kit - AHX000000
f1. (14) 3/8 ashers - AF 190000
f2. (7) 3/8 iz Nuts - AFT00004
f3. (7) 3/8 x 1 Bolts - AFS015100
f4. (12) 5/16 x 1 Bolts - AFB155190
f5. (24) 5/16 ashers - AF 180000
f6. (28) 5/16 iz Lock Nuts AFT155175
f7. Gasket - RGZ000000 (25)
f8. (3) 3/8 x 1 14 Bolts - AFS0157007
6. Internal Silencer (Pat. Pend.) - BSC180000
7. Filter - 18 Dia. x 62L - FCS186200
8. Owners Manual - ZBM000015
9. Decal - (1) Oneida Logo - ZBC000015
10. Labels
10a. Rotation Label - ZBC000029
10b. Caution / Exhaust Label - ZBS000004
10c. General Caution Label - ZBS000001
10d. Filter Maintenance Label - ZBS000007
10e. Caution / Check Frequently Label - ZBS000006
10f. Caution / Drum Cover Label - ZBS000005
11. all Bracket -Standard- SMS30000
12. Square to Round Inlet Transition to 8 dia. - BQX082000
Options for Dust Drums: OKD000000
13. 35 Gal. Fiber Drum Kit (Standard) - SDK351001
13a. Drum Lid w/ 10 Ring - SDX001000
13b. Hose Clamp 12 dia. (2) - ACB120000
13c. 35 Gal. Fiber Drum - SDS350000
13e. Flex Hose (10 dia. x 1) - DHF100000
13. 55 Gal. Fiber Drum Kit - SDK551001
13a. Drum Lid w/ 10 Ring - SDX001000
13b. Hose Clamps 12 (2) - ACB120000
13c. 55 Gal. Fiber Drum - SDS550000
13e. Flex Hose (10dia. x 1) - DHF100000
13. 55 Gal. Steel Drum Kit - SEK551001
13a. Drum Lid w/ 10 Ring - SEX551000
13b. Hose Clamps (2) - ACB120000
13c. 55 Gal. Steel Drum - SES550000
13e. Flex Hose (10 dia. x 1) - DHF100000
14.Filter Efficiency Gauge 0-5 H20 - VRG001005
14a. Vinyl Tubing Clear 5/16 O.D. - VRV003125 (8)
14b. Static Pressure Tip - VRP001875
14c. Mounting Flange for Pitot Tube - VRP010000
14d. Filter Efficiency Gauge Bracket - FXX000000
30. Optional 55 gal. Angle Iron Stand -
Part # ST 023055
1. Uprights - SXX000068 (4)
2. Braces - SXX000021 (7)
3. Feet - STX002001 (4)
Stand - Hardware Kit -
Part # AHX021023
A. (32) - 5/16 Bolts
Part # AFB155190
B. (32) - 5/16 iz Nuts
Part # AFT155175
C. (64) 5/16 Flat ashers
Part # AF 180000
Optional Angle Iron Stand
0
1234
5
INCHES W.C.
14 14a 14b
14d 14c
XXK200001 - 1 phase XXK200003 - 3 phase
f7 5
6
5a
5b
5c
7
f7
4
13b
13e
13b
13a
3
13c
5d
(8) 5/16 ashers
(8) 5/16 Nuts
(8) 5/16 ashers
(8) 5/16 Nuts
(7) 3/8 x 1 Bolts
(7) 3/8 ashers
(7) 3/8 Nuts
11
12
Optional Fan/Blower Outlet Transitions:
15. Square to 8 dia. For Fan Outlet - BQX308000 Uncrimped
15a. Square to 8 dia. For Fan Outlet - BQX308001 Crimped
2
1a
1e
1f
15 & 15a

Note: For cyclonic preseparation there must be an air tight seal between cyclone and dust
container. Dust bin must be located vertically under cyclone material drops down by gravity. 7
Pro 2000 Owners Manual O.A.S. 2007
c
VI. General Assembly Instructions
Cyclone
Barrel
Cyclone
Cone
2.
Cyclone
Barrel
Air Inlet
Fan /
Blower
Housing
1.
Air
utlet
Gasket
Material -
Outside of
Bolt Circle on
underside of
Housing.
Silicone nuts.
There are essentially three ways to assem le your collector
and to attach it to the racket. The way that is right for you
should e determined y expertise and manpower availa le.
When the units are all assem led they are very heavy and top
weighted. All of this should e taken into account efore
deciding on the method est suited for you.
Do N T use hook on motor to lift unit.
Gasket
Material
3.
3/8 Bolt / (2) Washers /
Serrated Nut per bolt hole
on each side and back.
4.
Collector
Hose Clamp
Hose Clamp
Flex Hose
Dust Bin
Gasket
Material
(12) 5/16 Bolts
(24) Flat ashers
(12) Serrated Nuts
Bolt
asher
Flange
asher
Nut
TOP
Motor &
Plate
Method #1 -
Bolt Fan/Blower housing to Cyclone barrel. Then bolt
Motor and Plate to Fan/Blower housing. Carefully lay
unit on its side and then bolt cone to barrel. Lift entire
unit up onto wall braket. Unit is extremely heavy and
top weighted, be advised!
Method #2 -
Bolt Fan/Blower housing to Cyclone barrel. Then bolt
Motor and Plate to Fan/Blower housing. Put Cone up
on Wall Bracket and orient holes. Lift assembled unit
onto cone making sure proper holes are lined up. Bolt
unit to bracket, then finish bolting barrel to cone.
Method #3 -
Bolt Fan/Blower housing to Cyclone barrel. Put Cone
up on Wall Bracket and orient holes. Lift assembled unit
onto cone making sure proper holes are lined up. Bolt
unit to bracket, then finish bolting barrel to cone. Lift
Motor & Plate onto Fan/Blower housing and bolt together
in proper direction.
Before you start, make sure you have cut and placed
the provided gasket material on top and bottom of the
Fan/Blower housing and the Cone as shown in the
diagrams. Then determine which direction you want
your filter to hang and which direction your ductwork
will enter the collector.
With all assemblies, make sure
rectangular air outlet is oriented on
Fan/Blower housing as you are looking
down as in Fig. 1A or facing it as shown
in diagrams. Then you can rotate
housing to whatever bolt position is
best for your shop.
TOP
VIEW
Fig. 1A
TOP
Gasket Material -
Outside of Bolt
Circle on top of
Housing. To
further eliminate
air leaks, a small
amount of silicone
should be used on
nuts to secure
motor plate.

8
Pro 2000 Owners Manual O.A.S. 2007
c
VII. Bracket Assembly
1. You must determine the direction the fan outlet will point to
proceed with this mounting assembly. The collector will seem
quieter if the outlet is aimed away from the area people tend to
work. Slots in the brackets are .406 x 1.00
Note: Bolts included to mount bracket to collector. Hardware
N T included to mount to wall.
2. Hold bracket against wall with top of plate at 60. Mark where
mounting holes fall. Mount wall bracket. For wall mounting, the
bolt centers on the brackets are at 16to accomodate most wall
stud spacing. See Fig. 1 & 2. Use a Level to ensure straightness.
3. Attach bracket to wall with lag screws, concrete anchors, or
other suitable hardware. See Fig. 2 & 3. Note: When installing
the brackets on a concrete wall, mount 2 x 4s between wall and
brackets to stabilize and dampen vibration.
4. Position Angle Ring around top of cone over bracket. Line up
one hole in Ring with hole in each bracket at desired rotation of
outlet. If rotation you desire does not correspond to an existing
hole in Angle Ring, drill new ones. Use three 3/8 bolts (included)
with washers & lock washers to secure the fan. See Fig. 4.
5. Attach tightly with bolts. See Fig. 4.
Note: Please do not install an Oneida Dust Collection System alone. Competent
assistance is advisa le. Units are heavy!
60 to top of plate.
Distance tor minimum
mounting height.
4
1
.406 x 1.00
16
12 Ga.
2
3
Level

VIII. Filter Assembly
9
Pro 2000 Owners Manual O.A.S. 2007
c
Note: Do not return exhaust air to the shop unless filter media is added.
External 62 Filter Assembly
1. Attach cartridge with hardware provided making sure
gasket is attached. See Fig. 1
2. If Filter requires additional support. Use the plate at the
top of the filter to support the filter assembly.
Note: If filter cartridge is located away from the cyclone
and motor, additional square-to-round connectors and pipe
can be purchased.
*Silencer Included.
For Filter cleaning instructions, see pg. 11.
Caution:
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters or other appliances.
1. Exhaust air to exterior of building.
Mount directly at the hole in exterior
wall or use a square-to-round transition
and ductwork to vent air to exterior.
No Filter Assembly
* Exhaust Diverter -
Can be used either
up or down
Option -
* nly usable on No Filter.
Caution: Rotating lades! Keep hands clear. Keep
people away from exhaust.
Fig. 1 Gasket
Material
(7) 3/8 x 1 Bolts
(14) ashers
(7) Serrated Nuts
Silencer
Filter
Filter
Clamp
Dust Bin

10
IX. Filter Maintenance
External Filter Cartridge Cleaning Intervals
Caution: Fine dust collected in filter is hazardous
to your health! Do not breathe!
When unit is turned off, use compressed air to blow dust off from
exterior of filter. Hold nozzle at least 8 away from filter pleats*.
Do not remove bottom dust pan before or during the blow-off
process! Let dust settle into dust pan. Unclip and dump out dust.
Filter removal is not required.
* WARNING: A close, direct blast with the compressed air nozzle
too close to filter, may damage filter media. Always wear safety
glasses while blowing off filter.
Fan / Blower & Cyclone Outside Placement
Fan / Blower has a TEFC - Totally Enclosed Fan Cooled motor.
Note: Use steel drum when placed outside.
Before Operation:
Check set screw and key in fan wheel, make sure fan wheel is secure. Fan blower should not vibrate. Fan
wheel is dynamic, two-plane balanced to IS 4.0 specifications.
Mount system and connect cyclone and dust bin. Make sure dust bin is in place before turning on the dust
collector.
Do not operate Fan / Blower unless Cyclone and Dust Bin are in place! Motor will overheat!
Electrical Wiring:
Make sure power source matches wire voltage configurations on motor.
Prior to connecting to the power line, check motor plate for proper voltage and rotation connection. Wire for
counter-clockwise rotation. Fan wheel must rotate counter-clockwise if looking down on fan housing.
Note: If fan is wired incorrectly and fan is rotating backwards, poor suction and airflow will result. See Wire
Diagrams on motor plate.
Use 12 gauge cord for the fan / blowers.
Lu rication:
The motor is supplied with pre-lubricated ball bearings, lubricated for the life of the bearing.
Caution: Rotating Fan Blades! Keep objects clear of outlet.
Pro 2000 Owners Manual O.A.S. 2007
c
Shown with optional Angle Iron
Stand and 55 gal. steel drum.

X. Filter Efficiency Gauge Mounting Instructions
Mounting Instructions
1. Mount brass static pressure tube in plenum with tip pointed into the air stream.
Use mounting bracket and sheet metal screws if interior of plenum is not accessible. Refer to drawings
for location of brass static pressure tube.
Gauge Reading Instructions
1. Gauge may need to be zeroed. Follow the instructions provided with pressure gauge.
3. Mount gauge up to 8 away, mounting it closer will not affect reading.
4. Connect clear tubing from brass static pressure tube to the port labeled high on the back of the
Pressure gauge.
5. Make sure the tubing is not crushed or kinked along its entire length, cut shorter if necessary.
4. hen the gauge rises to 3, its time to clean your filter.
2. Take the initial reading with cleaned filter(s) and the typical number of blast gates open in normal
operation.
3. Always read the gauge with the same number of gates open. The more gates open, the higher the
pressure reading on the gauge.
2. Refer to instructions provided with gauge for mounting to bracket.
After many cleaning cycles, a filters pressure will rise after each cleaning. An older
filter does not get as clean as a new filter.
11
Pro 2000 Owners Manual O.A.S. 2007
c
Air Flow
to Filter
Elbow Plenum
(Side View)
0
1234
5
INCHES W.C.

12
XI. Directions for Cleaning External Filter
Pro 2000 Owners Manual O.A.S. 2007
c
The External Filter can be cleaned using the following methods:
Wait a few minutes for internal dust to settle
then unclip and carefully empty dust bin.
Keep nozzle at least 6 from filter and keep your
pressure down. Closer blasts may damage filter
material. Rinse off INSIDE of filter. Let filter dry
completely before reuse or keep a spare filter
on hand.
2. Empty Dust Bin.
All steps should be done with a dust mask and eye protection.
3. Rinse with water. (Optional)
1. Compressed air from outside.
Blast air along pleats of the filter at about a 20
angle. Blast air out and away from you or anyone
in the general area.
Keep air nozzle at least 6 from filter. Closer
blasts may damage filter material. 6
Filter must be cleaned regularly or filter
damage may result. If gauge reaches 3,
it is time to clean your filter. Never allow
gauge to reach 5. You could destroy your
filter. See page 11.

13
Pro 2000 Owners Manual O.A.S. 2007
c
XII. Wiring Instructions for Magnetic Starter
Always use a licensed, professional electrician.
Follow Wiring Diagram on Motor.
Note: This Dust Collector is
pre-wired at the factory and
need only be plugged into a
NEMA 6020R dedicated
electrical receptacle. 5hp
single phase only.

Unplug unit before servicing or cleaning.
13
XIII. Troubleshooting
14
Pro 2000 Owners Manual O.A.S. 2007
c

XIV. Fire Hazards -
Read Before Installing and Operating
Do not use this product to collect other types of dust or flammable vapors.
Fire or explosion may occur!
Never collect sparks from a bench grinder into a wood dust collector.
Never introduce sparks or sources of ignition into the dust collector.
Personnel should keep at least 20 feet away from unit.
Check dust bin frequently and before leaving the shop for smoldering material.
Keep portable Fire Extinguishers handy.
The ABC type (dry chemical) is generally a good choice for small wood shops.
Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).
Be especially careful with sanding units. They can produce concentrations of dust in the combustible range. Make
certain enough air volume is at the suction point to capture all the particulate generated.
This high air volume will dilute the mixture below the lower limit of flammability. Be careful not to generate sparks into
the sanding dust.
Empty dust bin and clean filter often, especially when sanding.
Dont overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.
Sparks can be generated in several ways:
High-speed sanders and abrasive planers may strike foreign material
Saws and edgers may strike foreign material and create a red hot metal fragment.
Knots in hardwood can create frictional sparks.
Tramp metal when drawn into the collector can spark against ductwork.
Check wood stock for old nails and screws which can create red hot metal fragments.
Avoid using excessively large wood waste storage bins.
Always check storage bins for smoldering material before leaving for the day.
Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drainpipe)
Dont allow accumulation of layers of fine dust on horizontal surfaces. (Especially overhead lights, electrical boxes,
and fuse panels which can ignite dust)
Oneida Collectors are designed for WOOD DUST only!!
Wood shaping and cutting processes generate wood chips, shavings, and dust. These materials are considered
combustible. Air borne wood dust below 420 microns in size (.017 of an inch) in certain concentration ranges when
ignited can deflagrate (burn quickly).
An ignition source such as a spark, or ember, can ignite a dust mixture resulting in an expanding flame front, which
can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated fine dust can raise additional
dust clouds, which can cause a series of explosions that can level an entire building. Until this type of fire has been
witnessed, it is difficult to believe the devastation. This type of fire is rare but worth safeguarding against.
The best way to avoid a wood shop fire is to keep the shop clean. A shop ankle deep in dust with layers of fine dust
everywhere is an accident waiting to happen. A good dust collection system reduces overall fire hazards but also adds
new concerns. A fire hazard is still present. Combustible material is now in the dust collector and storage container.
It is the buyers responsibility to follow all applicable federal, state, local, SHA, NFPA, or authorities having
jurisdiction codes and regulations when installing and operating this dust collector.
Fire Marshalls may want the unit located outside of the building. If the collector is located inside the facility,
controls such as spark detection, suppression, or explosion venting may be required.
Most local jurisdictions consult or adopt NFPA ( National Fire Protection Agency) codes. However, other codes
may apply. Local codes may vary from jurisdiction to jurisdiction.
NFPA 664 Code book, Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking
Facilities, applies to woodworking operations that occupy areas of more than 5,000 sq. ft. or to areas where
dust producing equipment requires an aggregate dust collection flow rate of more than 1500 cfm (Cubic Feet
per Minute). This exempts some small operators from the NFPA code 664, but other codes may apply in your
jurisdiction. Consult your local Fire Marshall for help. Additional information can be found in NFPA Code Book
664.
The following points are worth heeding:
The customer assumes the responsibility for contacting their insurance underwriter with regard to specific
application requirements of explosion venting or if additional fire protection and safety equipment may be
required.
Unplug unit before servicing or cleaning.
15
Pro 2000 Owners Manual O.A.S. 2007
c

XV. Terms and Conditions
Please look over the shipped order very carefully in the presence of the delivery person for damage or
incomplete shipment before signing the delivery receipt. Please note any tears or irregularities in shipping
packaging, however slight, on the shipping delivery receipt. This could be an indication of extensive concealed
damage. The shipping company will not take responsibility if the damage is not noted on the delivery receipt.
In the event of shipping damage, call .A.S. immediately so we can expedite replacements. Please check
in all parts within 3 days from receiving order. Notify .A.S. immediately of any missing or incorrect parts.
.A.S. does not accept any claims for damage or shortage after 3 days from date of delivery.
Checking in Order
neida Air Systems warrants products it manufactures for a period of 5 years to the original purchaser from
the date of purchase. Items not manufactured by .A.S. are limited to their own manufacturers warranties.
This warranty does not apply to defects due directly or indirectly to misuse, negligence, accidents, abuse,
repairs, or alterations or lack of maintenance. This is neida Air Systems sole written warranty and any and
all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose,
are hereby limited to the duration of this written warranty. .A.S. does not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no
event shall .A.S.s liability under this warranty exceed the purchase price paid for the product and any legal
actions brought against neida Air Systems shall be tried in the State of New York, County of nondaga.
neida Air Systems shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our product.
neida Air Systems does not warrant or authorize use of wood dust collectors for other purposes. This
includes wood products that are treated, coated, or otherwise altered from their natural state.
Limited Warranty
Products will be shipped to Buyers single destination. Title and risk of loss shall pass to the Buyer upon
delivery to such destination. Buyer pays transportation expenses. Dates of shipment are advisory and .A.S.
will make reasonable efforts to ship on or before the date states for shipment, however, .A.S. shall not incur
any liability for failure to ship on that date.
Delivery Risk of Loss
Buyer must inform .A.S. of any shortage or damage, by so noting in writing, on the freight delivery bill prior
to signing to indicate receipt of shipment. All claims, including claims covered under the limited warranty, are
subject to inspection and investigation by .A.S.. .A.S. reserves the right to inspect and investigate all
returned products before Buyers claim is settled. All products returned for a refund must be unused, resaleable
and purchased within the last six months. There are no refunds on flex hose, custom made components,
or partial kit items. Kits must be returned in full (all components) for credit. There will be a 25% restocking
fee applied to any returned items.
Returned Goods Policy
*Note: Motors should e protected from extreme weather to prolong motor life.
Single phase motors should only e started and stopped up to 4 - 10 times per
hour. Starting single phase motors more frequently can cause heat uild up
and can cause the motor overload to trip or cause motor damage. In general,
motors should e started and stopped as little as possi le for maximum
lifespan and est economy (electrical use).
16
Pro 2000 Owners Manual O.A.S. 2007
c
Some parts of this system are outsourced and not made in the USA.

17
Pro 2000 Owners Manual O.A.S. 2007
c
XVI. Stand Assembly - STG023055
Bolt
Washer
Stand
Nut
68
23 7/8
23 7/8
23 7/8
23 7/8 23 7/8
23 7/8
23 7/8
(32) 5/16 Bolts
(32) 5/16 Nuts
(64) 5/16 Flat ashers
FRONT has no
lower brace across.
LEFT
RIGHT

Pro 2000 Owners Manual O.A.S. 2007
c
XVII. Accessories
Bolt Together
Angle Iron Stand
STG023055 - 55 gal. Stand
Replacement
Filter
FCS186200
Dust Containers
35 gal. Fiber
55 gal. Fiber
55 gal. Steel
ABX000000
The BAG Gripper provides the ability to use convenient plastic bags inside
your dust drum. It provides a constant, negative pressure on the outside
surface of the plastic bag that keeps it pulled tight against the sides of the
dust drum. Can be used with 35 and 55 gal. barrels. Must be wired into
your system.
The BAG Gripper
18 x 62 / 130 Sq. Ft. Spun-Bonded. Filters 99.9% of test material from 0.2 to 2
microns.
18

19
Pro 2000 Owners Manual O.A.S. 2007
c
XVIII. Fan Motor Maintenance
Per Baldor specifications, their 2 pole motors (3600 RPM) motors are to be relubricated every 5500 hours.
Table 1 - Service Conditions
Table 2 - Lubrication Interval ultiplier
Per Baldor specifications, add .30 ounces (8.4 grams) of Mobil Polyrex grease by weight or .6 cubic inches (2 teaspoons)
of Mobil Polyrex grease by volume.