Oneida Air Systems Super Dust Gorilla User manual

2 HP Cyclonic Dust Collector
Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204
Ph ne 1-800-732-4065 315-476-5151 Fax [phone] www. neida-air.c m
Owners Manual
Shown with optional
bolt together Angle
Iron stand.
*Models may
vary sligthly in
appearance.
T905
GORILLA
The
TM

Thank You for Choosing an Oneida Air Systems Product!
OAS manufactures and sells dust collection equipment only. Our qualified technicians and
sales staff are available 7:30am - 6:00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to
answer any questions concerning OAS products and dust collection. Call for ductwork design
and ductwork quotes, including system pricing and shipping cost.
Table of Contents
Page
Read the entire Owners Manua before insta ing or operating system!
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
XI.
XII.
XIII.
XIV.
XV.
XVI.
XVII.
2
3
4
5
6
7
8
9
0
2
3
4
5
6
7
8
System Start-Up Information
Commercial Configurations
General Specifications & Fan Performance Curves
Dimensions
General Assembly
General Assembly Instructions
Bracket Assembly
Filter Assembly
Filter Maintenance
Directions for Cleaning External Filter
Fan / Blower Wiring Diagram
Troubleshooting
Fire Hazards - Read Bef re Installing System
Terms and Conditions
Stand Assembly
Accessories
Fan Motor Maintenance
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c

2
I. System Start-Up Information
. Read the installation and maintenance instructions as well as the recommended
safety practices in this manual.
2. Install Ductwork completely before operating collector:
A.) Seal ductwork with silicone sealant or duct tape.
B.) Have Dust Bin in place and sealed.
3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 2
in this owners manual.
4. Have licensed electrician check current draw on motor with all gates open. Current
draw should not exceed maximum motor amperage. (OAS is not responsible for
damage to motors caused by improper installation, wiring or failure to follow these
directions.)
Caution
The Direct Drive Fan / Bl wer makes the system t p heavy!
Use extreme care when setting the unit up!
Warning
If amperage is t high - shut d wn immediately!
(See tr ublesh ting secti n.)
Warning
D n t perate Fan / Bl wer unless Cycl ne and Dust Bin
are in place. M t r will ver heat!
Warning
Check amperage draw during perati n with all blast gates
pen. Make certain amperage is n t utside perating limit
indicated n m t r plate!
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c

3
II. 2 p Dust Gorilla Configurations
Caution:
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters or other appliances.
1. Externa Cartridge Fi ter -
Silencer Included with Filter
1. Externa
Cartridge
Fi ter
2HP Super Dust G rilla Owners Manual
Si encer
inc uded
w/ Fi ter
O.A.S. 2005
c
Sh wn with
pti nal
Angle Ir n
Stand.
Cartridge Filter Media
Pleated Spun-Bonded Cartridge Filter 39 / 95 Sq. Ft.
Accredited, independent lab tested.
Bathed in teflon-like coating for easy dust release.
Captures 99.9% of Test Material from 0.2 - 2 microns.

III. General Specifications & Fan Performance Curves
- Sleeve kit adds 7 (4 is minimum)
- 35 gal. bin is 22 dia. x 22.5 h / 55 gal. bin is 22 dia. x 35.5 h
- Several Filter Options Available- Galvanized steel construction
- The collector can be hung on the wall, from the ceiling, or free standing support using
the 0 ga. angle iron ring at the top of the cone.
(See assembly instructions)
2.0 hp
Height without
Dust Bin
Cyclone
Diameter
Inlet
Diameter
Weight without
Dust Bin
TEFC
Motors
Class F
0/220v
20.2/ 0. amps
. 5 Service Factor
63 2  7
Approx. Wt.
22 lbs.
w/o drum or filter
Static pressure and volume together determine
a fans performance. Several factors, such as
layout of ductwork and diameter of openings,
can affect a fans performance.
2hp Dust Gori a System
405 max. cfm
Industrial TEFC 2hp motor
5/230v - 23.2/ .5 amps / . 5 Sevice Factor
6 gauge powder painted cyclone & ga. fan housing
7 dia. inlet / 8 rectangular outlet
4.25 dia. x 4 wide cast aluminum fan wheel
back inclined non-sparking, non-ferrous dynamic, two-planed
balanced to ISO 6.3 specifications.
Sound 78 - 79dB @ 0 with Built-in Silencer and Filter
95 Sq. Ft. Filter Media / Spun-Bond
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c
2hp Super Dust Gorilla Performance Curve
4
600
400
200
000
800
600
400
200
0
Air Flow (CFM)
Static Pressure @ Cyclone Inlet
0 2345 7689
405 349
25
46
954 779
55
Ma . CFM = 1405
405
349
25
46
954
779
55
.86
.82
.8
.77
.74
.6
.40
HP
(Output)
CFM

5
IV. Dimensions
For Minimum Mounting Heights w/ 39 Fi ter.
*Dimensi ns subject t slight variati n in manufacturing.
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c
Outlet - Can be rotated
independent of the inlet.
Inlet
2 
23
Top View
2 .75
Bolt
Circle
24.5
Outlet
Wall Mounts
3
Cyclone
Barrel
.5
30
2.625
Note: Check drum height, it will
affect your bracket height.
Always check the
actual system
height to
determine your
mounting height.
25. 25
50
2 Flex
22.5 - 35 gal. 34 - 55 gal.
2 Collar
on
drum
7 Dia.
4 3/ 6
Overall - Minimum 92 (35 Gal.) 03.5 (55 Gal.) This is using only 2 of Flex Hose. The minimum amount.
80 w/ 55 gal. drum
7  w/ 35 gal. drum
To lowest Bracket hole.
35 gal. - 70.5
55 gal. - 79.5
6
Included
Internal
Silencer
39 Filter
50
95 Sq. Ft.
for 9  Min. Height
Rotation
56

V. General Assembly
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c
Note: For cyclonic preseparation there must be an air tight seal between cyclone and dust
container. Dust bin must be located vertically under cyclone, material drops down by gravity.
Angle Iron Wall
Bracket
supports fan
housing and
cyclone
Cyclone inlet
7 dia.Connect to
main duct run out
to woodworking
machines
Cyclone Preseparator
separates 99% of the
wood waste from the
air stream. Eliminates
wear on the fan wheel
and maintenance on
the filter.
Cone
Flex Hose
Dust Bin
Light weight 35 or 55
gal. fiber dust bin. Steel
drum available for
outside applications.
Hose Clamp
Hose Clamp
Gasket
Material
Draw
Latches
Silencer
Rod
Brace
Washer
Wing Nut
Dust Pan
Do not
remove foam
from around
wire cage!
This is part of
si encer!
Gasket
Material
6
Cyclone
Barrel
Industrial TEFC
Motor Fan
Blower
Outlet
Gasket
Material
Clamp
Ring
Clamp
Ring

7
VI. General Assembly Instructions
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c
Cyclone
Barrel
Cyclone
Cone
2.
2. Clamp the fan housing and cyclone barrel to the
cyclone cone making sure you cut and put the supplied
gasket material around the top of the cone. Note: the
fan / b ower and the cyc one barre are very heavy.
The system wi be top heavy. Do not try to ift
co ector onto bracket by yourse f. Make sure you
have adequate he p.
3. Lift the collector onto the bracket and orient it into the
preferred position. Bolt each side and back securely
with supplied hardware.
4. Bolt the elbow-cartridge housing to the fan housing
outlet (rectangular), after applying gasket material. Clamp
the cartridge to the flat plate. Clamp the dust bins to the
bottom of the cartridge filters.
Cyclone
Barrel
Air Inlet
Fan / Blower
.
. Unclamp the blower housing, then cut and place
supplied gasket material around the top of cyclone
barrel, then re-clamp it to match the bracket configuration
and the desired angle for the cyclone inlet that you
choose.
Cycl ne Inlet and Fan / Bl wer are independent.
Filters can be t the right r left f the unit.
Air
Outlet
Gasket
Material
Fan / B ower is shipped c amped to Cyc one Barre .
Do NOT use
hook on motor
to lift unit.
GORILLA
The
TM
Gasket
Material
3.
3/8 Bolt / (2) Washers /
Serrated Nut per bolt hole
on each side and back.
GORILLA
The
TM
4.
Collector
Hose Clamp
Hose Clamp
Flex Hose
Dust Bin
2 ea. 5/ 6 Serrated Nuts
Clamp Ring
Clamp
Ring
Gasket
Material
GORILLA
The
TM
Clamp
Ring

8
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c
VII. Bracket Assembly
. You must determine the direction the fan outlet will point to
proceed with this mounting assembly. The collector will seem
quieter if the outlet is aimed away from the area people tend to
work. Slots in the brackets are .406 x .00
Note: Bolts included to mount bracket to collector. Hardware
NOT included to mount to wall.
2. Hold bracket against wall with top of plate at 56. Mark where
mounting holes fall. Mount wall bracket. For wall mounting, the
bolt centers on the brackets are at 6to accomodate most wall
stud spacing. See Fig. & 2. Use a Level to ensure straightness.
3. Attach bracket to wall with lag screws, concrete anchors, or
other suitable hardware. See Fig. 2 & 3. N te: When installing
the brackets n a c ncrete wall, m unt 2 x 4s between wall and
brackets t stabilize and dampen vibrati n.
4. Position Angle Ring around top of cone over bracket. Line up
one hole in Ring with hole in each bracket at desired rotation of
outlet. If rotation you desire does not correspond to an existing
hole in Angle Ring, drill new ones. Use three 3/8 bolts (included)
with washers & lock washers to secure the fan. See Fig. 4.
5. Attach tightly with bolts. See Fig. 4.
.406 x .00
Note: P ease do not insta an Oneida Dust Co ection System a one. Competent
assistance is advisab e. Units are heavy!
6
2 Ga.
2
3
Level
* Optional Mounting Direction
56 to top of plate.
Distance tor minimum
mounting height.
4

VIII. Filter Assembly
N te: D n t return exhaust air t the sh p unless filter media is added.
9
External 26 Filter Assembly
. Attach cartridge with hardware provided making sure
gasket is attached. See Fig.
2. If Filter requires additional support. Use the plate at the
top of the filter to support the filter assembly.
Note: If filter cartridge is located away from the cyclone
and motor, additional square-to-round connectors and pipe
can be purchased.
*Silencer Included.
Do not
remove foam
from around
wire cage!
This is part of
si encer!
For Fi ter c eaning instructions, see pg. 11.
Caution:
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters or other appliances.
. Exhaust air to exterior of building.
Mount directly at the hole in exterior
wall or use a square-to-round transition
and ductwork to vent air to exterior.
No Filter Assembly
* Exhaust Diverter -
Can be used either
up or down
Option -
* Only usable on No Filter.
Caution: Rotating b ades! Keep hands c ear. Keep
peop e away from exhaust.
2HP Super Dust G rilla Owners Manual O.A.S. 2005
c
Fig.
Gasket
Material
Cage
Silencer
Filter
Rod
Brace
Washer
Wing Nut
Dust Bin
GORILLA
The
TM
GORILLA
The
TM