Oneida Air Systems Super Dust Gorilla 2hp User manual

2HP
Commercial Cyclonic
Dust Collector
Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204
Ph ne 1-800-732-4065 315-476-5151 Fax [phone] www. neida-air.c m
Owners Manual

Thank You for Choosing an Oneida Air Systems Product!
OAS manufactures and sells dust collection equipment only. Our qualified technicians and
sales staff are available 7:30am - :00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to
answer any questions concerning OAS products and dust collection. Call for ductwork design
and ductwork quotes, including system pricing and shipping cost.
Table of Contents
Page
Read the entire Owners Manua before insta ing or operating system!
Proudly
Made in
the U.S.A.
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
XI.
XII.
XIII.
XIV.
XV.
XVI.
XVII.
2
3
4
5
7
8
9
10
11
12
13
14
15
1
17
18
System Start-Up Information
Commercial Configurations
General Specifications & Fan Performance Curves
Dimensions
General Tube Filter Layout Dimensions
General Assembly
Bracket Assembly
General Assembly Instructions
Filter Assembly
External Filter Bag Assembly
Fan Outlet Transition, Silencer and Angle Iron Stand
Wire Diagram
Filter / Fan / Blower Maintenance
Options
Troubleshooting
Fire Hazards - Read Bef re Installing System
Terms and Conditions
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2002
c
1

I. System Start-Up Information
O.A.S. 2002
c
2HP C mmercial W d Dust C llect r Owners Manual
1. Read the installation and maintenance instructions as well as the recommended
safety practices in this manual.
2. Install Ductwork completely before operating collector:
A.) Seal ductwork with silicone sealant or duct tape.
B.) Have Dust Bin in place and sealed.
3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 14
in this owners manual.
4. Have licensed electrician check current draw on motor with all gates open. Current
draw should not exceed maximum motor amperage. (OAS is not responsible for
damage to motors caused by improper installation, wiring or failure to follow these
directions.)
Caution
The Direct Drive Fan / Bl wer makes the system t p heavy!
Use extreme care when setting the unit up!
Warning
If amperage is t high - shut d wn immediately!
(See tr ublesh ting secti n.)
Warning
D n t perate Fan / Bl wer unless Cycl ne and Dust Bin
are in place. M t r will ver heat!
Warning
Check amperage draw during perati n with all blast gates
pen. Make certain amperage is n t utside perating limit
indicated n m t r plate!
2

II. 2 p Commercial Configurations
1. No Fi ter - Vent Outside -
3. Externa Tube Fi ters -
2. Externa Cartridge Fi ter -
Cartridge Filter Media
1 Pleated Cartridge Filter 130 Sq. Ft.
Spun bonded Polyester BIA ZHI / 487 Test - Rated C
Captures 99.9% of Test Material between 0.2 - 2.0 microns
@ 11 FPM Face Velocity
D NOT rem ve fabric straps fr m filter.
Tube Filter Media
12 oz. Needle Felted Polyester Tube Filters, singed on the inside.
10 to 1 air to cloth ratio is recommended.
FT-19 Tube Filters / 18.8 ft of filter area / 12 dia. x  long /
7.5 - 8 ceiling height
FT-25 Tube Filters / 25 ft of filter area / 12 dia. x 8 long /
9 - 10 ceiling height
FT-31 Tube Filters / 30 ft of filter area / 12 dia. x 10 long /
12 ceiling height
BIA ZHI / 487 Test - Rated C
Captures 99.5% of test material between 0.2 - 2.0 microns @ 11
FPM face velocity.
1. No Fi ter
Caution:
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters or other appliances.
2. Externa
Cartridge
Fi ter
3. Externa
Tube
Fi ter
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2002
c
3

III. General Specifications & Fan Performance Curves
4
STATIC PRESSURE (in. H20)
14
12
10
8
4
2
0
CFM - CUBIC FEET / MINUTE
200 400 00 800 1000 1200 1400 1 00 1800
900 CFM @ 8 W / C
OPERATING
RANGE
2hp Fan Performance Curve
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2002
c
2hp Commercia System
1220 max cfm
10 Max Static Pressure
900 cfm with typical ductwork
Industrial TEFC 2hp motor
115v / 20 amps. 208 - 230v / 11.4 - 10 amps
18 gauge galvanized cyclone & integral blower
7 dia. inlet / rectangular outlet
12 dia. x 4 wide cast aluminum fan wheel
balanced to .3 mls
Sound 75 - 85db at 10
- Sleeve kit adds 4 (Minimum)
- 35 gal. bin is 22 dia. x 22.5 h / 55 gal. bin is 22 dia. x 35.5 h
- Several Filter Options Available- Galvanized steel construction
- The collector can be hung on the wall, from the ceiling, or free standing support using
the 11 ga. angle iron ring at the top
(See assembly instructions)
2.0 hp
Height without
Dust Bin
Cyclone
Diameter
Inlet
Diameter
Weight without
Dust Bin
TEFC Leeson
Motors
SF 1.15
115v / 20 amps
208 - 230v /
11.4 - 10 amps
59.75 20.125 7
Approx. Wt.
122 lbs.
w/o drum or filter

IV. Dimensions
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2002
c
For Minimum Mounting Heights
5
Inlet
Outlet - Can be rotated independent of the inlet.
2hp - 20.125 ID
2hp - 23.125 ID
Rotation
Top View
22.5 - 35 gal.
35.5 - 55 gal.
2 Flex
42.25 - 2hp
21.75 Bolt Circle - 2hp
10.25 - 2hp
7.25 - 2hp
 - 2hp
18
Note: Check drum
height, it wi
affect your
bracket height.
Flex Hose
length can be
extended
to accomodate
a higher
mounting height.
A ways check the
actua system
height to
determine your
mounting height.
2hp - 21.75
74 - 35 gal.
88 - 55 gal.
2hp -
8 .25 - 35 gal.
99.25 - 55 gal.
Note: Use only if height
restrictions prevent
collector from being
mounted higher.
2
2hp Out et Detai
Outlet
C
4.25 - 2hp
4.875 - 2hp
.125 - 2hp
12
12
FTS0 0000 - 72 L
FTS080000 - 9  L
FTP080000 with zippers 9  L
(No 5 gal. bucket needed.)
FTP100000 - 120 L
12
2
23 1/2
Externa Tube Fi ter
7 - 2hp

V. General Tube Filter Layout Dimensions
Offset
Inlet
Plenum
(Plenum
will be 1 1/4
off wall)
8 12 18
25.75
2hp Cyc one
with Fan
Plenum can g t the right r left f the cycl ne.
Many c nfigurati ns are p ssible.
8 hole double wide plenum
32 3/4 wide x 7  long x 12 high
with 1/4 flange
7 hole single wide plenum
15 wide x 112 1/2 long x 12 high
hole double wide plenum
32 3/4 wide x 2 long x
12 high
5 hole single wide plenum
15 wide x 82 1/2 long x 12 high
4 hole single wide plenum
15 wide x 8 1/2 long x 12 high
5 hole double wide plenum
32 3/4 wide x 2 long x
12 high
4 hole double wide plenum
32 3/4 wide x 48 long x
12 high
2HP Cycl nic W d Dust C llect r Owners Manual O.A.S. 2002
c
Inlet
Outlet
Outlet can be r tated and
riented independent f inlet.
18
Externa Fi ter
P enum
23 1/2
Square to Round
Transition
w/ gasket
Silencer Large Radius
Adjustable Elbow
w/ centerline radius
of 1.75

7
Plenum Box
Standard 5 gallon buckets
(Not provided with system)
Tube Filters
1 oz. Needle Felted Polyester
1 Micron Filtration
HC - 12
Hose Clamps
HC - 12
Hose Clamps
Fan / blower exhaust air is blown into chamber
evenly dividing the air between the filter bags
U.S. TEFC Motor
Angle Iron Wall Brackets
support fan housing and
cyclone
Cyclone inlet
7 dia. - 2hpConnect
to main duct run out to
woodworking
machines
Cyclone
Barrel
Cyclone Preseparator
separates 99% of the
wood waste from the
air stream. Eliminates
wear on the fan wheel
and maintenance on
the filter.
Cone
Flex Hose
Dust Bin
Light weight 35 or 55
gal. fiber dust bin. Steel
drum available for
outside applications.
Note: For cyc onic preseparation there must be an air tight sea between cyc one and dust
container. Dust bin must be ocated vertica y under cyc one, materia drops down by gravity.
Band Clamp
Band Clamp
Hose Clamp
Hose Clamp
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2002
c
VI. General Assembly
Vortex Tube
Fan
Blower
Outlet
Square-to-Round
Transition

2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2002
c
1 .1875
VII. Bracket Assembly
1. You must determine the direction the fan outlet will point to
proceed with this mounting assembly. The collector will seem
quieter if the outlet is aimed away from the area people tend to
work. Slots in the brackets are .40  x 1.00
Note: Bolts included to mount bracket to collector. Hardware NOT
included to mount to wall.
2. Mount wall bracket. For wall mounting, the bolt center on the
left bracket will be 21.75 from the bolt center on the right bracket
for the 2hp unit. See Fig. 1.
3. Attach vertical arm of each bracket to wall with lag screws,
concrete anchors, or other suitable hardware. See Fig. 2 & 3.
N te: When installing the brackets n a c ncrete wall, m unt 2
x 4s between wall and brackets t stabilize and dampen vibrati n.
4. Position Angle Ring holding the fan housing over bracket.
Line up one hole in Ring with hole in each bracket at desired
rotation of outlet (two holes on each side will not line up). If
rotation you desire does not correspond to an existing hole in
Angle Ring, drill new ones. Use two 3/8 bolts (included) with
washers & lock washers to secure the fan. See Fig. 4.
. Attach tightly with bolts. See Fig. 4.
21.75 2hp
11.25 - 2hp
1
.40  x 1.00
2
3
Note: P ease do not insta an Oneida Dust Co ection System a one. Competent
assistence is advisab e. Units are heavy!
4
* Optional Mounting Direction
8

VIII. General Assembly Instructions - A Mode s
1. Wire motor according to wiring diagram on page 7. Use a
cord rated for a minimum of 20 Amps. Make sure the cord
you use is rated for the same power as the motor. Always
follow motor plate diagram and wire for correct rotation. (See
Wiring diagram secti n)
2. Secure fan assembly to cyclone barrel with ductwork clamp
ring. For final installation, use a small bead of silicone sealant
after positioning outlet and inlet between the two mating halves.
Align the inlet of the cyclone in the proper direction for the
system. See Fig. 1.
3. Hang unit from brackets. See Bracket assembly.
4. Attach the cone to the barrel with the metal clamping ring.
Lightly tighten the ring bolt. It is important that there is no air
leakage between the cone and barrel of the collector. There
should be a black rubber seal between the cone and barrel.
See Fig. 2
5. Attach flex hose to bottom of collector and to lid of dust bin.
Securely fasten hose clamps. Cut excess length of flex hose
if needed. Longer flex hoses are available for installations
requiring more height. There must be an air tight seal between
the collector and dust bin. See Fig. 3
. Make sure the dust bin lid sits securely and the rubber
gasket on the bin lid is in place on the barrel. Maintain an air
tight seal between cyclone and dust bin to prevent motor from
overheating
due to over amperage draw.
7. Attach the ductwork from the woodworking machines to the
inlet of the collector.
8. For Externa Cartridge, Tube Fi ter or No Fi ter mode s see
following pages 10 and 11.
9. On external filter models, attach Filter Plenum Assembly or
External Cartridge Assembly with 4 bolts. See Filter Assembly
Secti n, pages 10 & 11 f r details.
O.A.S. 2002
c
Fan
Assembly
Cyclone
Barrel
Clamp
Ring
1
3
Collector
Hose Clamp
Hose Clamp
Flex Hose
Dust Bin
2Barrel
Cone
Clamp
Ring
Wiring shou d be done by a icensed e ectrician!
Rubber
Seal
Outlet
Inlet
2HP C mmercial W d Dust C llect r Owners Manual
IMPORTANT:
Do not operate the collector until the dust bin is in place
and the connector is air tight or motor damage could result!
Stay c ear of fan exhaust whi e co ector is operating.
9