Optex OVS-01GT User manual

OVS-01GT Product set up guide Version. 12MAR2020

OVS 01GT Setup Guide
Product Package What’s inside
•OVS-01GT(E)
•Quick reference guide
•Installation Instructions
•12mm x 3mmφ screw (4 sets)
Options
•OVS-TB01: 45 degree mounting bracket

OVS 01GT Setup Guide

OVS 01GT Setup Guide
3 points to remember
-Mounting Height
-Angle
-Calibration

OVS 01GT Setup Guide
Mounting Height
0.5 m
If “activation mode” is used for
a sloped approach, the height
may need to be adjusted.

OVS 01GT Setup Guide：Pick an angle
45 degree
Set to “Activation mode”
90 degree
Set to “Protection mode”
TIP1:
90 degree can also be used as
more stable activation trigger.
TIP3:
Use OVS-01TB
45 degree bracket
TIP2:
Leave more than 30cm
distance from bars.

OVS 01GT Setup Guide
Calibration & Walk test (Area check)
Press and hold until LED
flash in blue
Stand off to a side.

OVS 01GT Setup Guide: Note about “Area Check”
Press and hold until LED
start flashing
Yes, OVS-01GT has “human cancellation”!
However, you can still check its detection
area by “Walking around”
Green Flash:
You are outside of a Microwave(Mw) trigger zone.
Yellow Flash:
You are inside of a Mw trigger zone.
Purple Flash:
You are inside of ultrasonic(Us) zone.
Red Flash:
You are triggering both Mw and Us.

OVS 01GT Setup Guide
Set up flow
1. Fix position: height and angle
2. Run cables and power the device up
3. Set detection range and run calibration
-See if the device functions on the default setting.
4. Adjust parameter.
Human cancel adjustment “5” will reduce “vehicle detection” accuracy.
5. Repeat Calibration and adjustment thorough
with testing with vehicles.
Recommended Initial setting (Default setting)

OVS 01GT Setup Guide
Examples

Interface Modification
New labels to be applied to production in Q3 2020
There is no change in performances, features and algorism to the current model.
(Not final: subject to change)
NEW Interface

OVS 01GT Setup Guide
Frequently told answers
1. Unlike Induction loops, OVS-01GT requires sensitivity tuning and calibrations.
2. Slopes and obstacles in the detection range will affect detection performances.
3. Yes, buttons are hard to press, but you will feel a click when pressed on circles.
4. From no wind, rain, storm we had issues in US or Japan where typhoons hit.
5. “Area check” is a way to check detection area by human walking around.
Ref. Installation Instructions P.3 : LED Status indicator
6. Recommended to try default setting to start. Ref. Installation Instructions P.16 : Sensor reset
“Human cancel adjustment” setting may offset vehicle detection “sensitivity”.

13
Input
Copyright (C) 2016 OPTEX CO., LTD. CONFIDENTIAL
Physical
circuit
status
Input
trigger type
Wat happens
when
triggered
Note
Wake LOpen Normally
Open
Enhances the
sensitivity of
detection
The default setting
Wake HOpen Normally
Closed
Enhances the
sensitivity of
detection
If no closed connection is made,
the device will stay at “Enhanced”
sensitivity.
(No human cancellation)
Inhibit LOpen Normally
Open
Mute the
sensitivity of
detection
The device will not detect when
the input circuit is closed.
Inhibit
HOpen Normally
Closed
Mute the
sensitivity of
detection
If no closed connection is made,
the device will stay at muted.
(No trigger at all)
Human detection (HD) mode
If no closed connection is made on
the input terminal, the device will
stay at “Enhanced” sensitivity.
Then, the device will go off by a
human presence.

OVS 01GT Setup Guide
For any question or set up guidance, please send inquiry to:
[e-mail]
Thank you.