Opus rolLAM 380 User manual

User’s guide
OPUS rolLAM 380
Keep to the following safety regulations as stated important contents for
safety.
Health & Safety precautions:
Before operating the machine please read the safety precautions,
manufacturer recommendations and the operation manual. The operation manual
should be easily available at any time for the operator
•
The machine should be installed on sturdy and level floor near the 230V/50 Hz
socket,
•The machine should be protected
against dust and moisture
•
The machine must not be placed near the heating units or ventilation units
•
The machine should not be used in vicinity of inflammable liquids or gases
•
Any heavy or sharp objects should not be put on the machine
•The supplying
cable should be protected against any damage, must not be used
to pull the machine or to remove the plug from a socket. If the cable is damaged
it must be exchanged immediately
.
•
During a long standstill or before replacing the machine, the plug should be
removed from a mains socket,
•
The machine should be kept away from children’s
•
Danger! Machine contains rotary elements. Take care of long hair, loose
jewellery
, ties and other loose pieces of clothing
rollers!
•
Danger!! The machine contains heating area
touch the machine or put any inflammable materials on the machine!
•
After using the laminator must be turned off by main switch or by unplugging it
from the power socket. Do not
cover the feed opening, so that the roll
down,
•
The machine must not be used for any other purposes than those indicated in
the instruction manual,
•
It is necessary to check and supervise if the machine operates correctly. In case
of any
malfunctions, it is required to contact the service team
•
The machine must not be located outside, should be operated in room
temperature higher than +8C
•
Before removing any cover from the machine, remove the plug from
a socket
•Using inappropriate lubric
ants causes the fire hazard
•
The machine should be operated according to general safety rules
•
The machine should be unplugged immediately, in case of any defect. Any
repairs can be conducted only by
authorised
•
There are high voltage parts inside thi
open the cover without
unplugging the cable from the socket
•.
Keep to the following safety regulations as stated important contents for
Before operating the machine please read the safety precautions,
manufacturer recommendations and the operation manual. The operation manual
should be easily available at any time for the operator
.
The machine should be installed on sturdy and level floor near the 230V/50 Hz
against dust and moisture
,
The machine must not be placed near the heating units or ventilation units
,
The machine should not be used in vicinity of inflammable liquids or gases
,
Any heavy or sharp objects should not be put on the machine
,
cable should be protected against any damage, must not be used
to pull the machine or to remove the plug from a socket. If the cable is damaged
.
During a long standstill or before replacing the machine, the plug should be
The machine should be kept away from children’s
and animal’s reach
Danger! Machine contains rotary elements. Take care of long hair, loose
, ties and other loose pieces of clothing
– they can be entangled into the
Danger!! The machine contains heating area
– pay special attention. Do not
touch the machine or put any inflammable materials on the machine!
After using the laminator must be turned off by main switch or by unplugging it
cover the feed opening, so that the roll
ers cool
The machine must not be used for any other purposes than those indicated in
It is necessary to check and supervise if the machine operates correctly. In case
malfunctions, it is required to contact the service team
The machine must not be located outside, should be operated in room
Before removing any cover from the machine, remove the plug from
ants causes the fire hazard
The machine should be operated according to general safety rules
,
The machine should be unplugged immediately, in case of any defect. Any
authorised
staff,
There are high voltage parts inside thi
s machine. To avoid electric shock, do not
unplugging the cable from the socket

•Be careful when using end cutter
•Moving parts can crush and cut.
•Do not touch the rollers while operating or directly after operating to avoid any
possible scald
•Safety switch is placed on the left front side of the machine. Press the
button in case of any emergency situation !
Recomendations:
•Use only recommended supplies and accessories,
•The machine is designed for lamination with pouch 25 – 250mic. Do not use
different pouch thickness,
•Individually cut pouch can badly dirt the rolls or wind around them,
•Remove all metal elements (clips, clamps, etc.) before laminating the document,
NOTE! Not complying with the recommendations above can result with
warranty void
Assembling and operating
•Instal the top and bottom film brackets using attache screws
•Apply on the rollers laminating foil, next stabilize it with adjustable collars
•Put the rollers with foil onot brackets
•Install upper foil using using below diagram:
roller with foil
foil safety cover
hot rollers
guide table
•Instal bottom foil using below diagram:
hot rollers
foil
Toller with foil
• Install safety cover and guide table
• Set the proper temperature and speed
•Laminate piece of material and check if foil on the rollers is well tensioned. If not,
adjust it using knobs on rollers or with roller tension handle. The handle is on the
right side of machine.
•The machine is ready to use.
Control Panel
TEMP (up&down) - adjust temperature
SPEED (up&down) – adjust speed
STBY –Stand by mode; temperature is set to 85°C
MEAS – Measures actual roller temperature
STOP – stops and runs rollers
REV – reverse function
HOT – Initial setting 110°C and speed 3
COLD – cold laminating
MEMO – Memory function. ---> Memory settings
On the display you can find also information about actual work mode: cold
lamination, hot lamination, running rollers and running fans

Programowanie pamięci
Using MEMO button you can seve your individual settings:
•Push the MEMO button for 2 seconds. The temperature and speed on
display will blink
•Using temperature and speed button to set demand value
•Pres 1-5 buttons to save your settings
Factory pre-set memory value
Attention!
If you don’t use the machine for 1 hour the temperature will go to 85°C. Also when
you Press the STBY button, the temperature will go to 85°C. Finally if you don’t use
the machine for 1 hour Since STBY mode, the Power will be hut down automatically
Cleaning:
During lamination foil can stick and soil the rollers. If they won’t be cleaned regularly
results of lamination may be unsatisfactory and the machine can be damaged. You
should clean the rollers often and reguraly.
Note! Before clearing turn off the laminator and unplug it from the socket
• Keep the rollers clean etery time after use
• Do not clean the rollers during work
• Use only delicate materials, others can damage the rollers.
• After finished work adjust adequate tension on the foil with tension handle. If
the tension is too tight, the foil can be stretched
Maintenance
Malfunction
Cause
Remedy
Machine will not
turn on
•Plug is not plugged in
•Power switch is in „off”
postion”
•Blown main Power fuse
•Plug the Power cord
into appropriate outlet
•Put the Power switch
to the „on” position
•Replace the fuse
There is Power but
the rollers are not
running after the
hot button is
pressed
•Emergency switch is
engaged
•Safety cover is not closed
•Guide table is not installed
correctly
•Blown motor fuse
•Disengage the
emergency switch
•Close the safety cover
to active the safety
switch
•Property install the
paper guide so that
the micro switch is
activated
•Replace the motor
fuse
The unit is not
heating up
•The machine is in „COLD”
mode
•Set temperature is lower
than the room temperature
•Switch to „HOT” mode
•Raise the temperature
according to the
recommended film
temperature
Curled lamination •Upward curl
•Downward curl
•Loosen the top roll film
tension
•Loosen the bottom roll
film tension
Unclear lamination •The main roller temperatures
are too low and lamination
Speer is too fast
•Raise the roller
temperatures and
lower the lamination
speed
MEMO Temperature
(°C) Speed
1 50 2
2 110 2
3 115 2
4 120 3
5 125 3

Technical Data:
Max lamination width: 380 mm
Max lamination Speed: 4000 mm / min
Max document thickness: 13 mm
Max foil thickness 250 mic
Lamination method: hot and cold lamination
Input current: 7A
Voltage: 240V / 50/60Hz
Power: 1550W
Net weight: 50 kg
Gross weight: 51 kg
Dimensions (WxDxH) 700 x 460 x 272(mm)
22.06.2012
dystrybutor: OPUS Sp. z o.o. • ul. Toruńska 8 • 44 - 122 Gliwice • www.opus.pl
Declaration of Conformity
Deklaracja Zgodności
OPUS Sp.z o.o. hereby declares that the machine specified below is in accordance with the
following directives and standards:
Opus Sp.zo.o. deklaruje z pełnąodpowiedzialnością, że urządzenie, którego dotyczy niniejsza
deklaracja jest zgodne z postanowieniami następujących dyrektyw UE oraz powiązanymi z nimi
normami zharmonizowanymi:
2006/95/WE; 2004/108/WE
EN 60950-1:2006+A11:2009+A1:2010+A12:2011; EN 55014-1:2006+A1:2009; EN 55014-2:1997+A2:200;
EN 61000-3-2:2006+A2:2009; EN 61000-3-3:2008
Name/ Nazwa : OPUS Sp. z o. o.
Address/ Adres : ul. Toruńska 8 44-122 Gliwice
Type of the machine / typ : Laminator
Model No / model : OPUS rolLAM 380
POLAND / Polska …………………………………
(Place / Kraj) (Signature / podpis)
08.03.2012 Krystian Nawrat
(Date / Data) (Full Name/ Imięi Nazwisko)