ORiNG TGPS-9168GT-M12-BP2-24V User manual

Quick Installation Guide
Version 1.1
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
ORing's Transporter series managed PoE Ethernet switches are designed
TM
for industrial applications, such as rolling stock, vehicle, and railway
applications. is managed Redundant RingTGPS-9168GT-M12-BP2-24V
E t h e r n e t s w i t c h w i t h 1 6 x 1 0 / 1 0 0 / 1 0 0 0 B a s e - T ( X ) P. S . E . a n d
8x10/100/1000Base-T(X) ports which is specifically designed for the
toughest and fully compliant with EN50155 requirement. The switch support
Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over 250 units
of connection), O-Chain and MSTP/RSTP/STP (IEEE 802.1s/w/D) can
protect your mission-critical applications from network interruptions or
temporary malfunctions with its fast recovery technology. TGPS-9168GT-
M12-BP2-24V also support Power over Ethernet, a system to transmit
electrical power up to 30 watts, along with data, to remote devices over
standard twisted-pair cable in an Ethernet network. Each TGPS-9168GT-
M12-BP2-24V switch has 16x10/100/1000Base-T(X) P.S.E. (Power Sourcing
Equipment) ports. P.S.E. is a device (switch or hub for instance) that will
provide power in a PoE connection. can alsoTGPS-9168GT-M12-BP2-24V
be managed centralized and convenient by Open-Vision, Except the Web-
based interface, Telnet and console (CLI) configuration. Therefore, the
switch is one of the most reliable choices for EN50155 highly-managed
Ethernet application.
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the evice upright against the walld
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Step 3: Slide the evice downwards and tighten the four screws for added stability.d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGPS-9168GT-M12-BP2-24V
Pictures Number
1
CD 1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power LED
3. R.M. status LED
4. Ring status LED
5. Fault LED
6. Console port
7. Relay output port
8. Power connector
9. Gigabit Ethernet ports with bypass
10. PoE-enabled Gigabit Ethernet ports
11. Link/ACT LED for Gigabit ports
12. Speed LED for Gigabit ports
13. Link/ACT LED for PoE-enabled Gigabit
Ethernet ports
14. Speed LED for PoE-enabled Gigabit
Ethernet ports
15. PoE LED
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The device provides Ethernet ports in M12 connector type. According to the link type, the switch
uses CAT e UTP cables to connect to any other network devices PCs servers switches3, 4, 5,5 ( , , ,
routers or hubs Please refer to the following table for cable specifications., ).
TGPS-9168GT-M12-BP2-24V
TGPS-9168GT-M12-BP2-24V
S w i tc h
E N 5 0 1 5 5
I N D U S T R I A L
6
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
Cable
Type
Max. Length
Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) M12 A-coding connector
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) M12 A-coding connector
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft) M12 A-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
QIG 1
15
714
12
13
4
5
6
7
8
21
3
4 51 2 3
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Console port pinouts
RS-23 2, 9600bps, 8, N, 1
EN50155 24-port managed
Gigabit PoE Ethernet switch
8 9 10
11
RSVD
RXD
GND
TXD
N.C.
The switch has one RS-232 (M12 5pin) console port,
located on the front panel. Use a M12-to-DB9
console cable to connect the console port to your
PC's COM port.
3A@24 VDC
Relay N .C.
Rel ay Outp ut
Con sole
RSVD
RXD
RS-23 2, 11520 0bps, 8 , N, 1
GND
TXD
N.C.
Pow er G1
LNK/A CT
Speed
G2
LNK/A CT
Speed
G3
LNK/A CT
Speed
G4
LNK/A CT
Speed
LNK/A CT
Speed
LNK/A CT
Speed
LNK/A CT
Speed
LNK/A CT
Speed
G5
G6
G7
G8
V1+
V1-
V2+
V2-
PoE
PoE
PoE
PoE
4
5
6
7
8
21
1 BI_DC +
2 BI_DD +
3 BI_DD -
4 BI_DA -
5 BI_DB +
6 BI_DA +
7 BI_DC -
8 BI_DB -
3
G1~ G8
LNK/A CT
Speed
LNK/A CT
Speed
LNK/A CT
Speed
LNK/A CT
Speed
PoE
PoE
PoE
PoE
FaultRingR.M.PWR2PWR1
Reset
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
1 BI_DC +
2 BI_DD +
3 BI_DD -
4 BI_DA - / PoE Vo ut+
5 BI_DB + / PoE Vout -
6 BI_DA + / PoE Vout +
7 BI_DC -
8 BI_DB - / PoE Vout -
G9~ G24
TGPS- 9168GT-M1 2-BP2-24V
8-Pin Gigabit Non-PoE Port
Definition
PIN Definition
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
8-Pin Gigabit PoE Port
Definition
PIN Definition
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA- with PoE Vout+
5 BI_DB+ with PoE Vout-
6 BI_DA+ with PoE Vout+
7 BI_DC-
8 BI_DB- with PoE Vout-
3A@24V DC
Relay N. C.
Rela y Outpu t
Cons ole
RSVD
RXD
RS-232 , 115200 bps, 8, N , 1
GND
TXD
N.C.
Powe r G1
LNK/AC T
Speed
G2
LNK/AC T
Speed
G3
LNK/AC T
Speed
G4
LNK/AC T
Speed
LNK/AC T
Speed
LNK/AC T
Speed
LNK/AC T
Speed
LNK/AC T
Speed
G5
G6
G7
G8
V1+
V1-
V2+
V2-
PoE
PoE
PoE
PoE
4
5
6
7
8
21
1B I_DC+
2B I_DD+
3B I_DD-
4B I_DA-
5B I_DB+
6B I_DA+
7B I_DC-
8B I_DB-
3
G1~G 8
LNK/AC T
Speed
LNK/AC T
Speed
LNK/AC T
Speed
LNK/AC T
Speed
PoE
PoE
PoE
PoE
FaultRingR.M.PWR2PWR1
Reset
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
1B I_DC+
2B I_DD+
3B I_DD-
4B I_DA- / Po E Vout+
5B I_DB+ / P oE Vout-
6B I_DA+ / P oE Vout+
7B I_DC-
8B I_DB- / P oE Vout-
G9~G 24
228
15
19.491.3
180
193.9
7.5
200.4
320
Ø5. 0
Ø8. 0
Power
Failur e
Bypass
Power
Failur e
Bypass
TGPS-9 168GT-M12-BP 2-24V
Unit =mm (Tolerance ±0.5mm)
Power
Failu re
Bypas s
Power
Failu re
Bypas s
1907-200-K9168T2241-FX011

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 1.1
Q I G
Specifications
S w i tc h
E N 5 0 1 5 5
I N D U S T R I A L
1. Launch the Internet Explorer and type in IP address of the device. The default static IP
address is 192.168.10.1
Follow the steps below to log in and access the system:
2. Log in with default user name and password (both are ).admin
Resetting
To reboot the switch, press the button less than 5 seconds.Reset
To restore the switch configurations back to the factory defaults, press the button more than 5Reset
seconds.
Physical Chara cteristic
Enclosure IP-30
Dimension (W x D x H) 32 0(W) x 91.3(D) x 228(H) mm (12.6 x 3.59 x 8.98 inch.)
Weight (g) 34 63 g
Environmenta l
-40 to 85 C (-40 to 185 F)
o o
Storage Temperature
5% t o 95 % Non-condensing
Operating Humidity
Regulatory App rovals
EN 55032, CISPR32, EN 61000-3-2, EN 61000-3-3, FCC Par t 15 B cl as s A
EMI
EN 55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS),IEC/EN 61000-4-4 (EFT),
IEC/EN 61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8(PFMF), IEC/EN 61000-4-11 (DIP))
EMS
IEC60068-2-27
Shock
IEC60068-2-31
IEC60068-2-6
Vibration
Free Fall
MTBF
16 1,351 hrs
EN60950-1
Safety
-40 to 75 C (-40 to 167 F)
o o
Operating Tempe rature
ORing Switch Model
10/100/1000 Base-T(X ) wi th
P.S.E. Po rts in M12 Auto
MDI/MDIX
16 x M12 connec tor (8 pin female A-coding)
Physical Ports
Technology
Ethernet Standard s
IEEE 802.3 for 10Base -T
IEEE 802.3u for 100Base -TX
IEEE 802.3ab for 1000 Ba se -T
IEEE 802.3x for Flow co nt rol
IEEE 802.3ad for LACP ( Li nk A ggregation Contro l Pr otocol)
IEEE 802.1p for COS (Cl as s of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1d for STP (Sp an ning Tree Protocol)
IEEE 802.1w for RSTP (Rapid Spa nn ing Tree Pr ot ocol)
IEEE 802.1s for MSTP (M ul tiple Spanning Tree Protocol)
IEEE 802.1x for Authent ic ation
IEEE 802.1AB for LLDP (Li nk L ay er D iscovery Protocol)
IEEE 802.3af/at PoE specifica ti on
8K
MAC Table
8
Priority Queues
10/100/1000Base -T( X) p orts
in M12 Auto MDI/MDIX
Store-and-Forward
Processing
Sw itch Properties
Sw itching latency: 7 us
Sw itching bandwidth: 48 G bp s
Max. Number of Ava ilable VLANs: 4095
IGMP multicast grou ps : 128 for each VLAN
Port rate limi ti ng: User Define
Security Features
Device Binding securi ty f eature
Enable/disable po rt s, MAC based port securit y
Port b as ed network access contr ol ( 802.1x)
VLAN (802.1Q) to segr eg ate and secure network traffi c
Radi us c entralized password manag em ent
SNMPv3 encrypted au th entication and access s ec urity
Https / SSH enhance network s ec urity
Software Fea tures
STP/RSTP/MSTP (IE EE 8 02.1D/w/s)
Redu nd ant Ring (O-Ring) wit h re cove ry t ime less than 30ms over 250unit s
TOS/ Di ffserv supported
Quality of Service (802 .1 p) for real-time traffic
VLAN (802.1Q) with VLAN t ag ging and GVRP support ed
IGMP Snooping
IP-based bandwidt h ma nagement
Application-bas ed Q oS management
DOS/DDOS auto preventio n
Port c on figura tion, status, stati st ics, monitoring, se cu rity
DHCP Server / Client suppor t
SNTP, N TP f or synchronizing of c lo cks over n etwork
SMTP Client
Modbus TCP
Up to 9.6K Bytes
Jumbo frame
After installing the and connecting cables, he green power LEDswitch t
should turn on. Please refer to the following tablet for LED indication.
CE EMC (EN 55024, EN 55032), FCC Part 15B, EN 50155(EN 50121-1, EN 50121-3-2)
EMC
EN 45545-2
Fire protection
*Note: This function is available by request only
EN50155 24-port managed
Gigabit PoE Ethernet switch
LED
Color
Status
Description
PWR1 Green On DC power module 1 activated
PWR2 Green On DC power module 2 activated
R.M Green On Device operating in Ring Master mode
Ring Green
On Ring enabled
Blinking Ring structure is broken
Fault Amber On Errors occur (i.e. power failure or port malfunctioning)
10/100/1000Base-T(X) P.S.E Ethernet ports
LNK/ACT Green On Port is linked
Blinking Transmitting data
PoE Green On Power supplied over Ethernet
Speed
Green On Port is running at 1000Mbps
Amber On Port is running at 100Mbps
Green/Amber Off Port is running at 10Mbps
10/100/1000Base-T(X) Ethernet ports
LNK/ACT Green On Port is linked
Blinking Transmitting data
Speed
Green On Port is running at 1000Mbps
Amber On Port is running at 100Mbps
Green/Amber Off Port is running at 10Mbps
ORing Industrial Networking Corp.
Copyright© 2019 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
TGPS-9168GT-M12-BP2-24V
8 x M12 connect or (8-pin female A-coding )with 2 x bypass f unction included
EN 50155 (IEC 61373)
Other
Warranty
5 ye ar s
Configurations
3. After logging in, you should see the following screen. For more information on
configurations, please refer to the user manual. For information on operating the device
using ORing’s Open-Vision management utility, please go to ORing website.
Power
Redu nd ant Input Power Du al DC in pu ts. 24 (16.8~30VDC) on 5-pin M23 female connector
26 Watts (power consumption of P.S E. is not included).
Fault Contact
Relay Relay output to carry capacity of 3A at 24VDC on M12 connector (5-pin M12 female A- co di ng )
Overload Current Protec ti on
Revers e Polarity P ro tection
Present
Present
Network Redundancy
O-Ring
O-Chain
MRP(*Note)
MSTP (RSTP/STP comp at ible)
PoE Ou tp ut Pow er
RS-232 Serial Conso le Port RS-232 in M12 (5-pin M12 female A-coding) connec to r wi th c on so le c ab le . 11 52 00 bp s, 8 , N, 1
Powe r Co nsumption(Typ.)
<24VDC@75Watts max.
≥24VDC@120Watts max.
TGPS-9168GT-M12-BP2-24V
TGPS-9168GT-M12-BP2-24V