ORiNG IGS-P9164 Series User manual

IGS-P9164GC-HV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
G19
G16
G14
G12
G10
G15
G13
G11
G9
G18
G17
Fail
Close
Fail
Open
V-/N
V+/L
V-/N
V+/L
Relay
PWR2
PWR1 IGS-P9164GC-LV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G16
G14
G12
G10
G15
G13
G11
G9
V1+
V1-
PWR1
Relay
COM
Fail Open
Fail Close
V2+
V2-
PWR2
G20
G19
G18
G17
IGS-P9164GF(X)-HV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
(P20)
G19
(P19)
1000X
G16
G14
G12
G10
G15
G13
G11
G9
LNK
/ACT
G18
(P18)
G17
(P17)
LNK
/ACT
TX
RX
TX
RX
TX
RX
TX
RX
Fail
Close
Fail
Open
V-/N
V+/L
V-/N
V+/L
Relay
PWR2
PWR1 IGS-P9164GF(X)-LV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
(P20)
G19
(P19)
1000X
G16
G14
G12
G10
G15
G13
G11
G9
LNK
/ACT
G18
(P18)
G17
(P17)
LNK
/ACT
TX
RX
TX
RX
TX
RX
TX
RX
V1+
V1-
PWR1
Relay
COM
Fail Open
Fail Close
V2+
V2-
PWR2
Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG
The is a managed industrial Ethernet switch designed for
power substation and rolling stock applications as it is fully compliant with the
requirements of IEC 61850-3 and IEEE 1613. The series consists of three
models: , , and each comes with
16x10/100/1000Base-T(X) ports and differ numbers or types of optical fiber
ports. The devices can be managed centrally via web browsers, TELNET,
Console or other third-party SNMP software as well as ORing’s
proprietary Open-Vision management utility. With complete support for
Ethernet redundancy protocols such as O-Ring (recovery time < 30ms over
250 units of connection) and MSTP (RSTP/STP compatible), the devices can
protect your mission-critical applications from network interruptions or
temporary malfunctions with its fast recovery technology. Boasting a wide
operating temperature from -40 C to 85 C, the switch can meet the
demanding requirements of power substations and rolling stock applications.
IGS-P9164 series
IGS-P9164GF IGS-P9164FX IGS-P9164GC,
oo
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Safety & Warnings
Dimension
Panel Layouts
Front View
1. LNK/ACT port for Ethernet ports
2. 10/100/100Base-T(X) Ethernet ports
3. Fiber ports (IGS-P9164GF/FX) or
Combo ports (IGS-P9164GC)
4. LNK status LED for fiber/combo ports
5. Console port
6. Power LED
7. PWR1 LED
8. PWR2 LED
9. R.M status LED
10. Ring status LED
11. Fault indicator
12. Relay output
13. Power 2 module
14. Power 1 module
15. Reset button
IGS-P9164 Series
IGS-P9164 Series
1907-2-29-IGSP9164-1.0
IEC 61850-3 Industrial Managed Ethernet
Switch
SWITCH
INDUSTRIAL
MANAGED
Contents
DIN-rail Kit
CD
IGS-P9164GF
or IGS-P9164FX
or IGS-P9164GC
Pictures Number
X1
X1
X1
QIG
Console Cable
X2
X1
X1
Wall-mount Kit
1
2
6
7
7
8
9
10
11
12
15
14
Power Cable
(For HV only) X2
Circuit Overloading: Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
115 .0
IGS-P9164GC-HV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
G19
G16
G14
G12
G10
G15
G13
G11
G9
87.0
48.0
17.5
7.50
R2.5
R3.95
80.5
62.0
87.9
G18
G17
Fail
Close
Fail
Open
V-/N
V+/L
V-/N
V+/L
Relay
PWR2
PWR1
159.0
154.0
IGS-P9164GC-LV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G16
G14
G12
G10
G15
G13
G11
G9
V1+
V1-
PWR1
Relay
COM
FailOpen
FailClose
V2+
V2-
PWR2
G20
G19
G18
G17
IGS-P9164GF(X)-HV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
(P20)
G19
(P19)
1000X
G16
G14
G12
G10
G15
G13
G11
G9
LNK
/ACT
G18
(P18)
G17
(P17)
LNK
/ACT
TX
RX
TX
RX
TX
RX
TX
RX
Fail
Close
Fail
Open
V-/N
V+/L
V-/N
V+/L
Relay
PWR2
PWR1 IGS-P9164GF(X)-LV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
(P20)
G19
(P19)
1000X
G16
G14
G12
G10
G15
G13
G11
G9
LNK
/ACT
G18
(P18)
G17
(P17)
LNK
/ACT
TX
RX
TX
RX
TX
RX
TX
RX
V1+
V1-
PWR1
Relay
COM
FailOpen
FailClose
V2+
V2-
PWR2
3
4
5
13
1
2
6
7
8
9
10
11
12
15
14
3
4
5
13
1
2
6
7
7
8
9
10
11
12
15
14
3
4
5
13
1
2
6
7
8
9
10
11
12
15
14
5
13
3
4
Rear View
12 1
1. Wall-mount screw holes
2. Din-rail screw holes
ORing Industrial Networking Corp.
Copyright© 2015 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
Installation
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
DIN-rail Installation
Use the mounting kits attached with the package and follow the steps below to install the
switch to a rail or to the wall.
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits onto both ends of the rear panel of the switch. A
total of six screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of the four screws.
Insert a screw head through the large parts of the keyhole-shaped apertures, and then
slide the switch downwards. Tighten the screw for added stability.
Wall-mounting
IGS-P9164GF(X)-HV
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G7
G5
G3
G1
G20
(P20)
G19
(P19)
1000X
G16
G14
G12
G10
G15
G13
G11
G9
LNK
/ACT
G18
(P18)
G17
(P17)
LNK
/ACT
TX
RX
TX
RX
TX
RX
TX
RX
Fail
Close
Fail
Open
V-/N
V+/L
V-/N
V+/L
Relay
PWR2
PWR1
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3, 4, 5, 5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 1.0
QIG
Cable Types and Specifications:
Cable Type Max. Length Conn ector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45
For pin assignments for different types of cables, please refer to the following
tables.
1000 Base-T RJ-45
Pin Number Assignment
1BI_DA+
2BI_DA-
3BI_DB+
4BI_DC+
5BI_DC-
6BI_DB-
7BI_DD+
8BI_DD-
10/100 Base-T(X) MDI/MDI-X
Pin Number MDI port MDI-X port
1TD+(transmit)RD+(receive)
2TD-(transmit)RD-(receive)
3 RD+(receive) TD+(transmit)
4NotusedNotused
5NotusedNotused
6 RD-(receive) TD-(transmit)
7NotusedNotused
8NotusedNotused
Note: “+” and “-” signs represent the polarity of the wires that make up each
wire pair.
To connect the console port to an external management device, you need an RJ-45 to
DB-9 cable, which is also supplied in the package. Below is the console port pin
assignment information.
Console Port Pin Definition
PC (male) pin assignment RS-232 with DB9 (female) pin
assignment (RJ45-DB9 cable) RJ45 pin assignment
PIN#2 RxD PIN#2 RxD PIN#2 RxD
PIN#3TxD PIN#3TxD PIN#3TxD
PIN#5 GND PIN#5 GND PIN#5 GND
10/100 Base-T(X) RJ-45
Pin Numb er Assignment
1TD+
2TD-
3RD+
4Notused
5Notused
6RD-
7Notused
8Notused
1000Base-T MDI/MDI-X
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4BI_DC+BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Resetting
To reboot the switch, press the button for 5 seconds.
To restore the switch configurations back to the factory defaults, press the button for 5 seconds.
Reset
Reset
Wiring
The switch supports dual redundant power supplies, Power Supply 1
(PWR1) and Power Supply 2 (PWR2). The connections for PWR1,
PWR2 and the RELAY are located on the front panel along with LAN
ports. Follow the steps below to wire power cables.
Insert the negative/positive wires into the V-/V+
terminals, respectively.
To keep the wires from pulling loose, use a small flat-
blade screwdriver to tighten the wire-clamp screws on the front
of the connector.
STEP 1:
STEP 2:
Power inputs
The switch provides fail open and fail close options for you to form relay circuits
based on your needs. If you want the relay device to start operating at power failure,
attach the two wires to COM and fail close to form a close circuit, vice versa. The
relay contact of the 3-pin terminal block connector will respond to user-configured
events according to the wiring.
Relay contact
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run
the ground connection from the ground screws to the grounding surface prior to connecting devices.
Grounding
Configurations
After installing the switch card, the green power LED should turn on. Please refer to the
following tablet for LED indication.
1. Launch the Internet Explorer and type in IP address of the switch. The default static IP address is
192.168.10.1
2. Log in with default user name and password
(both are ). After logging in, you should
see the following screen. For more information
on configurations, please refer to the user
manual. For information on operating the switch
using ORing’s Open-Vision management utility,
please go to ORing website.
admin
Follow the steps below to log in and access the system
Fail
Close
Fail
Open
V-/N V+/L
Specifications
IEC 61850-3 Industrial Managed Ethernet
Switch
SWITCH
INDUSTRIAL
MANAGED
LED Color Sta tus Description
PWR Green On DC power on
PW1 Green On DC power module 1 activated
PW2 Green On DC power module 2 activated
R.M Green On System running in Ring Master mode
On System running in Ring mode
Ring Green
Blinking Ring struct ure i s broken
Fault Amber On Faults occurs
10/100/1000Base-T(X) Fast Ethernet ports
Green On Port is connected and runni ng at 1000Mbps
Amber On Port is connected and running at 100Mbps
LNK/ ACT
Green/Amber Off Port running at 10Mbps
1000Base-X fiber ports
On Ethernet links connected
LNK/ ACT Green
Blinking Transmitting data
100Base-FX fiber ports
On Ethernet links connected
LNK/ ACT Green
Blinking Transmitting data
100/1000Base-X SFP ports
On Ethernet links connected
LNK/ ACT Green
Blinking Transmitting data
ORing Switch Model IGS-P9164GF-MM
Physical Ports
Fiber Ports Number
Technology
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3z for 1000Base-X
IEEE 802.3ab for 1000Base-T
IEEE 802.3ad for LACP (Link Aggregation Control Protocol)
IEEE 802.3x for Flow control
IEEE 802.1p for COS (Class of service)
IEEE 802.1Q for VLAN Tagging
IEEE802.1wforRSTP(RapidSpanningTreeProtocol
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
Power
Redundant Input power
Power consumption(Typ.)
LV model : Dual power inputs with 12~48VDC on dual 2 pin terminal block
HV model : Dual power inputs with 85~264VAC/88~373VDC on dual 3-pin terminal block
LV:18Watts
HV :18.5Watts
Overload current protection
Reverse polarity protection
Present
Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 115.0 (W) x 159.0(D) x 154.0(H) mm (4.52x 6.26 x 6.06 inch)
10/100/1000Base-T(X) Ports
in RJ-45 Auto MDI/MDIX
MAC Table 8K
RS-232 Serial Console Port
Priority Queues 8
Processing Store-and-Forward
Switch Properties
Switch latency: 7 us
Switch bandwidth: 40Gbps
Max. Number of Available VLANs: 256
IGMP multicast groups: 128 for each VLAN
Port rate limiting: User Define
Security Features
Device Binding security feature
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
VLAN (802.1q) to segregate and secure network traffic
Radius centralized password management
SNMPv3 encrypted authentication and access security
Https / SSH enhance network security
Software Features
STP/RSTP/MSTP (IEEE 802.1D/w/s)
RedundantRing(O-Ring)withrecoverytimelessthan30msover250units
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging and GVRP supported
IGMP Snooping for multicast filtering
IP-based bandwidth management
Application-based QoS management
DOS/DDOS auto prevention
Port configuration, status, statistics, monitoring, security
DHCP Server / Client support
SMTP Client
Modbus TCP
Network Redundancy O-Ring, Open-Ring, O-chain, MRP, MSTP (RSTP/STP compatible), Fast Recovery
RS-232 in RJ45 connector with console cable. Baud rate setting: 115200bps, 8, N, 1
Fiber Ports Specification
Fiber Ports Standard 1000Base-SX
Fiber Mode Multi-mode Single-mode
Fiber Diameter ( m)µ62.5/125 m
50/125 m
µ
µ
Fiber Optical Connector SC SC
Typical Distance (Km) 0.55 Km 30 Km
Wave length (nm) 850 nm 1310 nm
Max. Output Optical Power
(dbm) -8 dbm
Min. Output Optical Power
(dbm) -15 dbm
Optical Input Power-
minimum (Sensitivity) -34 dbm
0dbm -0 dbm
-18 dbm
Optical Input Power-
maximum (Saturation)
Link Budget (db) 8.5 db 19 db
Weight ( g) LV:1780g
HV:2216g
16
9/125 mµ
4
Processing Up to 9.6K Bytes
Fault Contact
Relay Relayoutputtocarrycapacityof1Aat24VDC on3pinterminalblock
100Base-FX
-4 dbm
-9.5 dbm
Single-mode
SC
10 Km
1310 nm
-3 dbm
-9.5 dbm
-20 dbm
-3 dbm
10.5 db
9/125 mµ
1000Base-LX100Base-FX
Multi-mode
62.5/125 m
50/125 m
µ
µ
SC
2Km
1310 nm
0dbm
-31 dbm
7.5 db
-14 dbm
-23.5 dbm
IGS-P9164FX-MM IGS-P9164GF-SS IGS-P9164FX-SS IGS-P9164GC
Gigabit Combo Port with
10/100/1000Base-T(X) and
100/1000Base-X SFP Port
- 4
-
-
-
-
-
-
-
-
-
-
-
-
Packet Buffer 4Mbits
LV:21Watts
HV :20.7Watts
LV:18Watts
HV : 18.5Watts
LV:21Watts
HV : 19.3Watts
LV:17Watts
HV:18Watts
Weight (g) 710 g 740 g722 g 735 g 735 g 740 g
Environmental
-40to85 C(-40to185 F)
oo
Storage Temperature
-40to75 C(-40to167 F)
oo
Operating Temperature
5% to 95% Non-condensingOperating Humidity
LV:1780g
HV:2186g
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN55012-4)EMI
EN61000-4-2 (ESD)
EN61000-4-3 (RS)
EN61000-4-4 (EFT)
EN61000-4-5 (Surge)
EN61000-4-6 (CS)
EN61000-4-8
EN61000-4-11
EMS
IEC60068-2-27Shock
IEC60068-2-32
IEC60068-2-6Vibration
EN60950-1 Safety
Free Fall
Warranty
5 years
IEC 61850-3, IEEE 1613Power Automation
IGS-P9164 Series
IGS-P9164 Series
LV:1796g
HV:2205g
LV:1780g
HV:2216g
LV:1796g
HV:2205g