ORiNG TXPS-1080-M12-24V Series User manual

PoE
LNK/ ACT
PoE
LNK/ ACT
PoE
LNK/ ACT
PoE
LNK/ ACT
10/100 M
500M
TXPS -1 080- M12- 24 V
P1 P5
P2 P6
P3 P7
P4 P8
Faul tPWR2
Pow er
PWR1PWR
Rela y N.C.
3A@2 4VDC
Rel ay Outp ut
V1+
V1-
V2+
V2-
Tx+ Rx +
Tx-
Rx-
Tx+: P oE Vout+
Tx- : Po E Vout+
Rx+: P oE Vout-
Rx- : Po E Vout-
10/100 M
500M
10/100 M
500M
10/100 M
500M
Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The TXPS-1080-M12-24V series is an un-managed PoE Ethernet switch
with 8x10/100/500Base-T(X) P.S.E. ports, specifically designed for the
toughest environment and fully compliant with EN50155 requirement. The
P.S.E ports enable the TXPS-1080-M12-24V series to transmit electrical
power, along with data, to remote devices over a standard
cable. With EN50155 compliance and M12 connectors, the device ensures
reliable and robust connections against environmental disturbances, such
as vibration and shock. In addition, the wide operating temperature range
o o
from -40 C to 75 C allows the device to operate in extreme weather. The -BP2
model also provides two sets of bypass ports that ensure constant network
connectivity during power failure. Even if the switch loses power, traffic will
continue to flow unimpeded through the link.
twisted-pair
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the device upright against the wall
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the device downwards and tighten the four screws for added stability.
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TXPS-1080-M12-24V or
TXPS-1080-M12-BP2-24V
Pictures Number
1
CD 1
Dimension
TXPS-1080-M12-24V TXPS-1080-M12-BP2-24V
Panel Layouts
Front View
1. Power status LED
2. Power1 status LED
3. Power2 status LED
4. Fault LED
5. Power input port
6. Relay output port
7. LNK/ACT & Speed LED for Ethernet ports
(10Mbps/100Mbps)
8. LNK/ACT & Speed LED for Ethernet ports (500Mbps)
9. PoE Ethernet ports
(P5-P8 of TXPS-1080-M12-BP2-24V are bypass ports)
10. PoE status LED
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The device provides Ethernet ports in M12 connector type. According to the link type, the switch
uses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.
TXPS-1080-M12-24V Series
TXPS-1080-M12-24V Series
1907-2-29-TXPS1080M1224V-1.0
Switch
EN50155
EN50155 8-port unmanaged
PoE Ethernet switch
I N D U S T R I A L
125 .0
196 .0
155 .8
65. 0 21 .3
15. 0
125 .0
196 .0
155 .8
65. 0
1
2
3
4
5
6
7
8
9 9 10
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
PoE Power Distribution
For pin assignments of the LAN ports, please refer to the following tables.
QIG 1
PoE
LNK/AC T
PoE
LNK/AC T
PoE
LNK/AC T
PoE
LNK/AC T
10/100M
500M
Ø5. 0
Ø8. 00
7.5 0
168.4
56. 5
86. 0
TXPS-10 80- M12- BP2- 24V
P1 P5
P2 P6
P3 P7
P4 P8
FaultPWR2
Powe r
PWR1PWR
Relay N.C.
3A@24V DC
Rela y Output
V1+
V1-
V2+
V2-
Ø4. 0
Tx+ Rx+
Tx-
Rx-
Tx+: PoE Vo ut+
Tx- : PoE Vout +
Rx+: PoE Vo ut-
Rx- : PoE Vout-
10/100M
500M
10/100M
500M
10/100M
500M
175.9
Power
Failur e
Bypass
PoE
LNK/AC T
PoE
LNK/AC T
PoE
LNK/AC T
PoE
LNK/AC T
10/100M
500M
Ø5. 0
Ø8. 00
7.5 0
168.4
56. 5
86. 0
TXPS-1 080 -M1 2-2 4V
P1 P5
P2 P6
P3 P7
P4 P8
FaultPWR2
Powe r
PWR1PWR
Relay N.C.
3A@24V DC
Rela y Output
V1+
V1-
V2+
V2-
Ø4. 0
Tx+ Rx+
Tx-
Rx-
Tx+: PoE Vo ut+
Tx- : PoE Vout +
Rx+: PoE Vo ut-
Rx- : PoE Vout-
10/100M
500M
10/100M
500M
10/100M
500M
175.9
Unit =mm (Tolerance ±0.5mm)
#1 #2
#3
#4
M12 D-coding Pin Definition
Pin No. Description
#1 TX+ with PoE Vout+
#2 RX+ with PoE Vout-
#3 TX- with PoE Vout+
#4 RX- with PoE Vout-
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
M12 D-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
M12 D-coding connector
500Base-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
M12 D-coding connector

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 1.0
Q I G
Switch
EN50155
I N D U S T R I A L
Configurations
After installing the switch and connecting cables, start the device by
turning on power. The green power LED should turn on. Please refer to the
following tablet for LED indication.
LED
Color
Status
Description
PWR Green On Power is enabled
PWR1 Green On DC power module 1 activated
PWR2 Green On DC power module 2 activated
Fault Amber On Power 1 or Power 2 module failure
10/100/500M Base-T(X) Ethernet ports
10/100M LNK/ACT (Upper LED) Green On Port is running at 10/100Mbps
500M LNK/ACT (Lower LED) Amber On Port is running at 500Mbps
PoE Blue On PoE power is enabled
Regulatory Approvals
EN 55 032, CISP R32, EN 610 00-3-2, E N 61000-3 -3, FCC Part 15B cla ss A
EMI
EN 55 024 (IEC/ EN 61000- 4-2 (ESD) , IEC/EN 61 000-4-3 ( RS),IEC / EN 61000 - 4-4 (EFT),
IEC /EN 61000 -4-5 (Sur ge), IEC/ EN 61000- 4-6 (CS), I E C/EN 610 0 0-4-8(P FMF),
IEC /EN 61000 -4-11 (DI P))
EMS
IEC 60068-2 -27
Shoc k
IEC 60068-2 -31
IEC 60068-2 -6
Vibration
Free Fa ll
MTBF 315 273 hrs
Specifications
Power
Redundant Inp ut Power
Power Consump tion(Typ.) 3 Wat ts (power c onsumpt ion of P.S.E . is not incl uded)
Physical Characteristic
Encl osure IP-30
Dime nsion (W x D x H) 125 (W) x 65(D) x 1 96(H) mm (4 .92 x 2.56 x 7. 66 inch. )
Weight (g ) 993 g
Environmental
o o
-40 t o 85 C (-40 t o 185 F)
Storage Temperatur e
5% to 9 5% Non-co ndensin g
Operating Humi dity
Fault Contact
Relay Re l ay outpu t to carry ca pacity o f 3A at 24VDC o n M12 conne ctor (5-p in M12 A- coding)
Ove rload Curren t Protection
Reverse Polarity Pro t ection
Pre sent
Pre sent
o o
-40 t o 75 C (-40 t o 167 F)
Operating Temperat ure
ORing Swi t ch Model
10/1 00/500Base -T(X) Port s
in M12 W ith P.S.E. 8 x M12 conn ector (4 pin D-coding)
Physical Ports
Technology
Ethe rnet Standar d s
IEEE 8 02.3 for 10Bas e-T
IEEE 8 02.3u for 100B ase-TX
IEEE 8 02.3x for Flow c ontrol
IEEE 8 02.3at compl i ant PoE sp e cification ( M aximum 30Watts pe r p ort)
4K MA C a ddresses
MAC Table
Stor e-and-Forward
Proc essing
8 x M12 conn e ctor (4-pin D-coding,
bypass f u nction included on P5~8)
101 5 g
TXPS-1 080-M12-24V TXPS-1080-M1 2 -BP2-24V
Dua l DC inputs . 24 (12~57 VDC) VDC on 5 -pin M23 co nnector
PoE Output Power 60 Wa tts (12~24 VDC)/ 120 Wa t t s (24~57 V DC)
Warranty 5 ye a rs
306 849 hrs
ORing Industrial Networking Corp.
Copyright© 2018 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
LED indicators
Gree n : Power LED x 3
Power Indicat or
Ambe r : Indicate PWR 1 o r PWR2 failure
Fault Ind i cator
Top Green for 10 /100Mbps por t L ink/Act indi c ator.
Midd le Amber for 500 Mbps port Link / Act indicato r
Bott om blue for PoE Injected in d icator
10/1 00/500Base -T(X) M12
port i ndicator and PoE
indi cator
CE EM C (EN 55024 , EN 55032) , FCC Par t 15B, EN 50 121-3-2 ( EN 50155)
EMC
EN 60 950-1
EN 50 155
Othe r
Saf e ty
TXPS-1080-M12-24V Series EN50155 8-port unmanaged
PoE Ethernet switch
TXPS-1080-M12-24V Series