ORiNG DGS-7084GCP-AIO_S SERIES User manual

D
DG GS S- -7 70 08 84 4G GC CP P- -A AI IO O_ _S S S SE ER RI IE ES S
I
In nd du us st tr ri ia al l M Ma an na ag ge ed d G Gi ig ga ab bi it t B By yp pa as ss s
E
Et th he er rn ne et t S Sw wi it tc ch h
U
Us se er r’ ’s s M Ma an nu ua al l
V
Ve er rs si io on n 2 2. .0 0
D
De ec c, , 2 20 01 12 2
w
ww ww w. .o or ri in ng g- -n ne et tw wo or rk ki in ng g. .c co om m

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 1
COPYRIGHT NOTICE
Copyright © 2010 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for
a specified warranty period from the invoice date (5 years for most products). ORing will repair
or replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., NO.542-2, Jhongjheng Rd., Sindian District, New Taipei City 231, Taiwan, R.O.C.
Tel: + 886 2 2218 1066 // Fax: + 886 2 2218 1014
Website: www.oring-networking.com
Technical Support
E-mail: [e-mail]
Sales Contact
E-mail: [e-mail] (Headquarters)
[e-mail] (China)

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 2
Table of Content
Getting to Know Your Switch...............................................................5
1.1About the DGS-7084GCP-AIO_S Industrial Switch......................................................5
1.2Software Features ..............................................................................................................6
1.3Hardware Features.............................................................................................................7
Hardware Overview...............................................................................8
2.1Front Panel..........................................................................................................................8
2.2Back Panel...........................................................................................................................9
2.3Rack mount kit assembly...................................................................................................9
2.4Front Panel LEDs .............................................................................................................11
Cables...................................................................................................13
3.1Ethernet Cables................................................................................................................13
3.1.1100BASE-TX/10BASE-T Pin Assignments...................................................................13
3.2SFP.....................................................................................................................................14
WEB Management...............................................................................15
4.1Configuration by Web Browser.......................................................................................15
4.1.1About Web-based Management......................................................................................15
4.1.2Basic Setting...................................................................................................................17
4.1.2.1 System Information......................................................................................................17
4.1.2.2Admin & Password.......................................................................................................18
4.1.2.3 IP Setting......................................................................................................................19
4.1.2.4 IPv6 Configuration.......................................................................................................20
4.1.2.5 HTTPS..........................................................................................................................21
4.1.2.6 SSH ..............................................................................................................................22
4.1.2.7 LLDP............................................................................................................................22
4.1.2.8 Backup/Restore Configuration.....................................................................................26
4.1.2.9 Firmware Update..........................................................................................................26
4.1.3DHCP Server..................................................................................................................27
4.1.3.1Setting.................................................................................................................27
4.1.3.2DHCP Dynamic Client List.............................................................................27
4.1.3.3DHCP Client List...............................................................................................28
4.1.4Port Setting.....................................................................................................................28
4.1.4.1Port Control .......................................................................................................28
4.1.4.2Rate Limit ...........................................................................................................30

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 3
4.1.4.3Port Trunk...........................................................................................................31
4.1.4.4Loop Guard........................................................................................................37
4.1.5Redundancy....................................................................................................................37
4.1.5.1O-Ring.................................................................................................................37
4.1.5.2O-Chain...............................................................................................................38
4.1.5.3MSTP ...................................................................................................................40
4.1.5.4Fast Recovery mode........................................................................................48
4.1.6VLAN.............................................................................................................................49
4.1.6.1VLAN Membership Configuration................................................................49
4.1.6.2Private VLAN .....................................................................................................60
4.1.7SNMP.............................................................................................................................61
4.1.7.1SNMP-System....................................................................................................61
4.1.7.2SNMP-Communities.........................................................................................64
4.1.7.3SNMP-Users.......................................................................................................65
4.1.7.4SNMP-Groups....................................................................................................66
4.1.7.5SNMP-Views.......................................................................................................67
4.1.7.6SNMP-Accesses ...............................................................................................68
4.1.8Traffic Prioritization .......................................................................................................69
4.1.8.1Storm Control....................................................................................................69
4.1.8.2Port QoS .............................................................................................................70
4.1.8.3QoS Control List...............................................................................................71
4.1.8.4Queuing Counters............................................................................................72
4.1.8.5Wizard..................................................................................................................73
4.1.9Multicast.........................................................................................................................74
4.1.9.1IGMP Snooping.................................................................................................74
4.1.9.2IGMP Snooping Status....................................................................................75
4.1.10Security......................................................................................................................76
4.1.10.1Remote Control Security Configuration.....................................................76
4.1.10.2Device Binding..................................................................................................76
4.1.10.3ACL......................................................................................................................82
4.1.10.4802.1x..................................................................................................................94
4.1.11Warning....................................................................................................................109
4.1.11.1System Warning..............................................................................................109
4.1.12Monitor and Diag.....................................................................................................112
4.1.12.1MAC Table ........................................................................................................112
4.1.12.2Port Statistic....................................................................................................115
4.1.12.3Port Mirroring..................................................................................................117

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 4
4.1.12.4System Log Information...............................................................................119
4.1.12.5Cable Diagnostics..........................................................................................120
4.1.12.6SFP Monitor.....................................................................................................121
4.1.12.7Ping....................................................................................................................121
4.1.12.8IPv6 Ping...........................................................................................................122
4.1.13Factory Defaults.......................................................................................................123
4.1.14System Reboot.........................................................................................................123
Command Line Interface Management ...........................................124
5.1About CLI Management...............................................................................................124

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 5
Getting to Know Your Switch
1.1 About the DGS-7084GCP-AIO_S Industrial
Switch
DGS-7084GCP-AIO_S series are managed redundant ring Ethernet switch with 8xGigabit
combo ports and 4x1000Base-X SFP ports. With completely support of Ethernet
Redundancy protocol, O-Ring (recovery time < 30ms over 250 units of connection) and
MSTP/RSTP/STP (IEEE 802.1s/w/D) can protect your mission-critical applications from
network interruptions or temporary malfunctions with its fast recovery technology. ORing’s
thunder switch series provide advanced IP-based bandwidth management which can limit the
maximum bandwidth for each IP device. User can configure IP camera and NVR with more
bandwidth and limit other device bandwidth. ORing’s thunder switch series also support
application-based QoS. Application-based QoS can set highest priority for data stream
according to TCP/UDP port number. ORing’s special Device Binding function can permit only
allowed IP address with MAC address to access the networking. Hacker cannot access the
IP surveillance network without permission. It can avoid hacker from stealing video privacy
data and attacking IP camera, NVR and controllers. ORing’s thunder series switch also
provided advanced DOS/DDOS auto prevention. If there is any IP flow become big in short
time, ORing’s thunder switch will lock the source IP address for certain time to prevent the
attack. It’s hardware based prevention so it can prevent DDOS attack without using CPU
resource. DGS-7084GCP-AIO_S series includes 2 sets of bypass ports that protect the
network from failures and Network maintenance by ensuring network integrity during power
loss. Each set of these bypass ports includes Network ports and Monitor ports. The
Network ports are used for connection to main-network connections and provide protection
mechanism, and the Monitor ports are used for down-linking local networking device. When
the power is on, the operating mode of the Bypass ports is set to Normal, and the local
networking device is connected with main-network. When power failure occurs, the Bypass
port(s) is/are swiftly set to bypass mode to isolate the main-network from the local networking
device. And all functions of DGS-7084GCP-AIO_S series can also be managed centralized
and convenient by Open-Vision, Except the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the switch is one of the most reliable choice for highly-managed
and Gigabit Fiber Ethernet application.

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 6
1.2 Software Features
Support 8xgigabit combo ports
Support 4x1000Base- X SFP ports
Support Jumbo frame up to 9.6K Bytes
Supports O-Ring (recovery time < 30ms over 250 units of connection), MSTP/RSTP/STP
(IEEE 802.1s/w/D) for Ethernet Redundancy
Provide two optical bypass function
Supports IPv6 new internet protocol version
Provided HTTPS/SSH protocol to enhance network security
Supports SMTP client
Supports IP-based bandwidth management
Supports application-based QoS management
Supports Device Binding security function
Supports DOS/DDOS auto prevention
Supports DDM (Digital Diagnostic Monitoring) function (P1 ~ P8)
IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
Supports SNMP v1/v2c/v3, RMON and 802.1Q VLAN Network Management
Support ACL, 802.1x User Authentication for security
Multiple notification for warning of unexpected event
Windows utility (Open-Vision) support centralized management and configurable by
Web-based interface, Telnet and Console (CLI)
Support LLDP Protocol
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 7
1.3 Hardware Features
One 100~240VAC power input for DGS-7084GCP-AIO_S
Operating Temperature: -40 to 70oC
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing
Casing: IP-30
8 x Gigabit combo ports and 4 x 1000 Base-X SFP ports
Console Port support Command Line Interface(CLI)
Dimensions : 300 (W) x 165 (D) x 88 (H) mm

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 8
Hardware Overview
2.1 Front Panel
The following table describes the labels that stick on the DGS-7084GCP-AIO_S
Port Description
Gigabit SFP ports 4 1000Base-X on SFP port
Gigabit Combo
Ports
10/100/1000Base-T(X) RJ-45 + 100/1000Base-X SFP Ports
Console Use RS-232 with DB9 connecter to manage switch.
DGS-7084GCP-AIO_S
1. Bypass power LED and status LED indicator
2. LC Type Fiber Optic bypass port
3. Reset button. Push the button 3 seconds for system reset; 5 seconds for factory default.
4. Ethernet switch LED Status
．LED for PWR When the any PWR ON, the green led will be light on.
．LED for PWR1. When the PWR1 links, the green led will be light on.
．LED for PWR2. When the PWR2 links, the green led will be light on.
．LED for R.M (Ring master). When the LED light on, it means that the switch is the ring
master of O-Ring.
．LED for Ring. When the LED light on, it means the O-Ring is activated.
．LED for Fault Relay. When the fault occurs, the amber LED will be light on.
5. Console Port (RJ-45 interface for RS-232 protocol)
6. Ggiabit Combo Port with 100/1000Base-X SFP Ports

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 9
7. Ggiabit Combo Port with 10/100/1000Base-T(X)
8. LED for Ethernet ports Link/Act indicator
9. LED for Ethernet ports duplex/collision indicator
10. 1000Base-X SFP Port
11. LED for SFP ports link status.
2.2 Back Panel
The back panel of DGS-7084GCP-AIO_S is shown as below:
1. Power socket of power input for AC 100V~240V / 50~60Hz.
2. Relay output to carry capacity of 1Aat 24VDC
2.3 Rack mount kit assembly
You can find the rack mount kit and the screws in the packing box. Please assembly the rack
mount kit on the switch with screws as below picture.

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 10

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 11
2.4 Front Panel LEDs
Bypass LED indicator:
LED Color Status Description
Power Green On When the power module is in
PWR UP state, the green LED
lights on.
Power Fail Amber On When the power fail, the
amber led will be light on.
Bypass Green On When the bypass function is
enabled, the LED will be light
on.
Normal Green On When the bypass function is
disabled, the LED will be light
off.
Ethernet switch LED indicator:
LED Color Status Description
PWR Green On When the power module is in
PWR UP state, the green LED
lights on.
Blinking When the system is
upgrading firmware
PWR 1/2 Green On When the PWR links, the
green led will be light on.
R.M Green On When the system is operating
in O-Ring Master mode
Ring Green
On Ring enabled.
Slowly blinking Ring has only One link. (lacks
one link to build the ring)
Fast blinking Ring work normally.
Fault Amber On When the fault occurs, the
amber LED will be light on.
Ggiabit Combo Port with 10/100/1000Base-T(X) Gigabit Ethernet ports
Speed Green On Port link up
Blinking Data Transmitted
Duplex Amber On Full-Duplex
Off Half-Duplex
Ggiabit Combo Port with 100/1000Base-X Combo SFP Ports
LINK/ACT Green On Port link up
Blinking Data Transmitted
1000Base-X SFP Ports

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 12
LINK/ACT Green On Port link up.
Blinking Data transmitted

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 13
Cables
3.1 Ethernet Cables
The DGS-7084GCP-AIO_S switch has standard Ethernet ports. According to the link type,
the switch use CAT 3, 4, 5,5e UTP cables to connect to any other network device (PCs,
servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-TX Cat. 5/Cat. 5e 100-ohm
UTP UTP 100 m (328ft) RJ-45
3.1.1 100BASE-TX/10BASE-T Pin Assignments
The DGS-7084GCP-AIO_S switch support auto MDI/MDI-X operation. You can use a
straight-through cable to connect PC to switch. The following table below shows the
10BASE-T/ 100BASE-TX MDI and MDI-X port pin outs.
10/100 Base-T MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
1000 Base-T MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 14
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
3.2 SFP
The Switch has fiber optical ports with SFP connectors. The fiber optical ports are in
multi-mode (0 to 550M, 850 nm with 50/125 µm, 62.5/125 µm fiber) and single-mode with LC
connector. Please remember that the TX port of Switch Ashould be connected to the RX port
of Switch B.
SwitchA SwitchB
Fiber cord

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 15
WEB Management
4.1 Configuration by Web Browser
This section introduces the configuration by Web browser.
4.1.1 About Web-based Management
An embedded HTML web site resides in flash memory on the CPU board. It contains
advanced management features and allows you to manage the switch from anywhere on the
network through a standard web browser such as Microsoft Internet Explorer.
The Web-Based Management function supports Internet Explorer 5.0 or later. It is based
on Java Applets with an aim to reduce network bandwidth consumption, enhance access
speed and present an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to explicitly modify
the browser setting in order to enable Java Applets to use network ports.
Preparing for Web Management
The default value is as below:
IPAddress: 192.168.10.1
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.10.254
User Name: admin
Password: admin
System Login
1. Launch the Internet Explorer.
2. Type http:// and the IP address (default is 192.168.10.1)of the switch. Press
“Enter”.

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 16
3. The login screen appears.
4. Key in the username and password. The default username and password is
“admin”.
5. Click “Enter” or ”OK” button, then the main interface of the Web-based
management appears.
Login screen
Main Interface
Main interface

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 17
4.1.2 Basic Setting
4.1.2.1 System Information
The switch system information is provided here.
System Information interface
.
Label Description
System Contact
The textual identification of the contact person for this managed
node, together with information on how to contact this person.
The allowed string length is 0 to 255, and the allowed content is
the ASCII characters from 32 to 126.
System Name
An administratively assigned name for this managed node. By
convention, this is the node's fully-qualified domain name. A
domain name is a text string drawn from the alphabet (A-Z, a-z),
digits (0-9), minus sign (-). No space characters are permitted as
part of a name. The first character must be an alpha character.
And the first or last character must not be a minus sign. The
allowed string length is 0 to 255.
System Location
The physical location of this node(e.g., telephone closet, 3rd
floor). The allowed string length is 0 to 255, and the allowed
content is the ASCII characters from 32 to 126.
Timezone Offset
Enter the name of contact person or organization
Provide the time zone offset relative to UTC/GMT.
The offset is given in minutes east of GMT. The valid range is
from -720 to 720 minutes.
Click to save changes.
Click to undo any changes made locally and revert to previously
saved values.

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 18
4.1.2.2 Admin & Password
This page allows you to configure the system password required to access the web pages or
log in from CLI.
Label Description
Old Password Enter the current system password. If this is incorrect, the new
password will not be set.
New Password The system password. The allowed string length is 0 to 31, and
the allowed content is the ASCII characters from 32 to 126.
Confirm password Re-type the new password.
Click to save changes.

DGS-7084GCP-AIO_S SERIES User’s Manual
ORing Industrial Networking Corp 19
4.1.2.3 IP Setting
Configure the switch-managed IP information on this page.
Label Description
DHCP Client Enable the DHCP client by checking this box. If DHCP fails and
the configured IP address is zero, DHCP will retry. If DHCP fails
and the configured IP address is non-zero, DHCP will stop and
the configured IP settings will be used. The DHCP client will
announce the configured System Name as hostname to provide
DNS lookup.
IP Address Assign the IP address that the network is using. If DHCP
client function is enabling, you do not need to assign the IP
address. The network DHCP server will assign the IP address
for the switch and it will be display in this column. The default IP
is 192.168.10.1
IP Mask Assign the subnet mask of the IP address. If DHCP client
function is enabling, you do not need to assign the subnet mask
IP Router Assign the network gateway for the switch. The default
gateway is 192.168.10.254
VLAN ID Provide the managed VLAN ID. The allowed range is 1 through
4095.
SNTP Server SNTP is an acronym for Simple Network Time Protocol, a
network protocol for synchronizing the clocks of computer
systems. SNTP uses UDP (datagrams) as transport layer.
Click to save changes.