Osram Traxon e:cue ProPoint Kontour Narrow RGB User manual

ProPoint Kontour
INSTALLATION GUIDE
V1.0
Cover:
ProPoint Kontour Narrow RGB
ProPoint Kontour Wide RGB
ProPoint Kontour Narrow RGBW
ProPoint Kontour Wide RGBW
ProPoint Kontour Narrow Static White
ProPoint Kontour Wide Static White

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 2 of 25
CONTENT
1. INTRODUCTION 4
2. INSTALLATION 10
3. SYSTEM CONFIGURATION 16
4. CARE AND MAINTENANCE 20
5. TECHNICAL SPECIFICATION 21
6. TROUBLESHOOTING 24
7. WARRANTY INFORMATION 24

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 3 of 25
SAFETY AND OPERATION
This installation guide uses the following special statement categories to alert you to key items:
1. WARNING - Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
2. CAUTION - Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
3. NOTICE - Indicates information considered important for the proper operation of the product but not hazard
related.
4. Please review this manual completely prior to beginning the installation process and take note of the
following:
•The ProPoint luminaire and associated accessories must be installed by a qualified person in conjunction
with all applicable electrical codes and standards.
•The ProPoint luminaire does not contain any user-serviceable parts. Opening of the luminaire will void the
warranty.
•Do not use the product if the cables are damaged.
•Handle the luminaire carefully to prevent damage during installation. Rough handling may damage the
internal electronics and void the warranty.
•Do not attempt installation in wet or severe weather conditions.
•Do not stare directly into the light beam while the unit is illuminated.
•IP66 rated. The ProPoint luminaire is not suitable for direct immersion in water.
•Do not operate the ProPoint luminaire without a connection to earth surface without a suitable earth
connection (refer to local standards).
•The ProPoint luminaire is designed for operation at 120-277V AC (ETL)/220-240V AC (CE). Voltages
outside of this range may damage the fixture and will void the warranty.
•The ProPoint luminaire housing may become hot during normal operation and present a risk of burn
injury and fire hazard. Exercise caution when working in proximity to the luminaire and make sure that
combustible material does not contact the housing or lens.
•Failure to keep the luminaire within the operating temperature range (-30°C to +55°C/-22°F to +131°F) will
result in improper operation and will void the product warranty.
•Do not use harsh chemicals, cleaning solvents or strong detergents when cleaning the luminaire.
•Persons installing this product should make sure:
i. The installation complies with all applicable codes, state and local laws, ordinances, standards and
safety regulations.
ii. The installation environment is carefully studied and suitable surge protection measure(s) is taken.
Suggested surge protection measures for outdoor application should reach “Live to Neutral” 5kV,
“Live/Neutral to Earth” 10kV.
iii. All luminaires can pass surge test up to “Live to Neutral” 1kV, “Live/Neutral to Earth” 2kV according
to EN61547 standard.
iv. They are qualified or competent in the handling of electrical equipment.

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 4 of 25
1. INTRODUCTION
1.1 Product Overview
The Traxon Kontour is an AC line powered exterior luminaire used to distinguish facades, walls, and architectural
borders with a concentrated, even radiance. ProPoint Kontour’s compact, low-profile design is available in four
lengths, two widths and is combined with a clip mounting system for efficient installation.
This manual is intended for use with DMX512 versions of the ProPoint Kontour.
Model Length Power Consumption
(Typ.)
Available PXL Configuration
ProPoint Kontour Narrow
300mm / 12” 4W
•300mm can be 1PXL
•600mm can be 1PXL or 2PXL
•1200mm can be 1PXL, 2PXL, or 4PXL
•2400mm can be 1PXL, 2PXL, 4PXL, or 8PXL
•PXL Configuration is set during manufacturing,
and is not adjustable on-site
600mm / 24” 8W
1200mm / 48” 16W
2400mm / 96” 32W
ProPoint Kontour Wide
300mm / 12” 5W
600mm / 24” 10W
1200mm / 48” 20W
2400mm / 96” 40W
Features:
•Available lengths: 300mm / 12”, 600mm / 24”, 1200mm / 48”, 2400mm / 96”
•Diffused lens cover / Round diffused lens cover
•Long Run Lengths up to 305m (1000 ft) @ 277V with ProPoint Kontour Narrow
•Long Run Lengths up to 240m (800 ft) @ 220-240V with ProPoint Kontour Narrow
•DMX512
•Daisy Chain System
•Outdoor Applications
a. IP66-rated
b. IK08 Impact Rating for ProPoint Kontour Narrow and IK07 Impact Rating for ProPoint Kontour Wide.
c. ANSI 3G Rated
d. Suitable for coastal environment

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 5 of 25
1.2 Getting Assistance
Additional product information is available on the Traxon web site:
•www.traxontechnologies.com & www.osram.us/traxon
For additional support, please contact Traxon Technical Support:
For Americas Regional Support:
•[phone] – Business Hours Technical Support
•[phone] – After Hours Technical Support
•TRXT[email protected]
For Asia Pacific Regional Support
•[email protected]
For Europe, Middle East and Africa Regional Support
•[email protected]
•[email protected]

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 6 of 25
1.3 Dimensions
FIG.1: ProPoint Kontour Narrow
300mm / 11.8”
600mm / 23.6”
1200mm / 47.2”
2400mm / 94.5”
75mm / 3”
100mm / 3.9”
130mm / 5.1”
15mm / 0.6”
15mm / 0.6”
15mm / 0.6”
250mm / 9.8”
540mm / 21.3”
1500mm / 59”
46.5mm / 1.8”
63mm / 2.5”
58mm / 2.3”
With Mounting Bracket
Without Mounting Bracket
46.5mm / 1.8”
59.5mm / 2.3”
44mm / 1.7”
12.8mm / 0.5”
9.5mm / 0.4”
Power/Data Input side Power/Data Output side
46.5mm / 1.8”
46.5mm / 1.8”
46.5mm / 1.8”
46.5mm / 1.8”

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 7 of 25
FIG.2: ProPoint Kontour Wide
300mm / 11.8”
600mm / 23.6”
1200mm / 47.2”
2400mm / 94.5”
75mm / 3”
100mm / 3.9”
130mm / 5.1”
15mm / 0.6”
15mm / 0.6”
15mm / 0.6”
250mm / 9.8”
540mm / 21.3”
1500mm / 59”
75mm / 3”
69mm / 2.7”
84mm / 3.3”
With Mounting Bracket
12.8mm / 0.5”
9.5mm / 0.4”
75mm / 3”
66mm / 2.6”
70mm / 2.8”
Without Mounting Bracket
Power/Data Input side Power/Data Output side
75mm / 3”
75mm / 3”
75mm / 3”
75mm / 3”

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 8 of 25
1.4 Packing Contents
FIG.3: Packing Contents
ProPoint Kontour 300mm/12”, 600mm/24”, 1200mm/48”, 2400mm/96”
(Temporary waterproof end cap included)
2 × Mounting Bracket
(2 screws pre-installed, 1 screw for each)
2 × Safety cable (Optional Accessory)
Power/Data Input side Power/Data Output side
1.5 Component Overview
Luminaire Options
The ProPoint Kontour is available in the following sizes:
Model Model Power Consumption (Typ.) Power Factor Input Voltage Range Operating
Temperature
Narrow
300mm / 12” 4W
≥0.9
120-277V AC 50/60 Hz
(ETL)
220-240V AC 50/60 Hz
(CE)
-30°C to +55°C /
-22°F to +131°F
600mm / 24” 8W
1200mm / 48” 16W
2400mm / 96” 32W
Wide
300mm / 12” 5W
600mm / 24” 10W
1200mm / 48” 20W
2400mm / 96” 40W
The in-rush current data of ProPoint Kontour is shown in the following tables:
NOTE • n: the number of fixtures in the chain
•NW: Narrow
•WD: Wide
•F: Flat
Description In-rush current @ 120V Present time
Quantity 1 Fixture 2 Fixtures 3 Fixtures …n Fixtures
300mm / 12” NW/WD 15A 30A 45A …n*15A 0.05ms
600mm / 24” NW/WD 15A 30A 45A …n*15A 0.05ms
1200mm / 48” NW/WD 9.7A 19.4A 29.1A …n*9.7A 0.8ms
2400mm / 96” NW 9.7A 19.4A 29.1A …n*9.7A 0.8ms
2400mm / 96” WD 11A 22A 33A …n*11A 0.8ms

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 9 of 25
Description In-rush current @ 230V Present time
Quantity 1 Fixture 2 Fixtures 3 Fixtures …n Fixtures
300mm / 12” NW/WD 30A 60A 90A …n*30A 0.05ms
600mm / 24” NW/WD 30A 60A 90A …n*30A 0.05ms
1200mm / 48” NW/WD 19.8A 39.6A 59.4A …n*19.8A 0.8ms
2400mm / 96” NW 19.8A 39.6A 59.4A …n*19.8A 0.8ms
2400mm / 96” WD 23.9A 47.8A 71.7A …n*23.9A 0.8ms
Description In-rush current @ 277V Present time
Quantity 1 Fixture 2 Fixtures 3 Fixtures …n Fixtures
300mm / 12” NW/WD 36A 72A 108A …n*36A 0.05ms
600mm / 24” NW/WD 36A 72A 108A …n*36A 0.05ms
1200mm / 48” NW/WD 21.4A 42.8A 64.2A …n*21.4A 0.8ms
2400mm / 96” NW 21.4A 42.8A 64.2A …n*21.4A 0.8ms
2400mm / 96” WD 24A 48A 72A …n*24A 0.8ms
The ProPoint Kontour is available with the following color options:
Model Color Options Lens Options DMX Control
Channels2Color Temperature
Narrow
Color Changing (RGBW)
RGBW
120˚
Ch1: Red
Ch2: Green
Ch3: Blue
Ch4: White
RGBW (White: 4000K standard)
Color Changing (RGB)
RGB
Ch1: Red
Ch2: Green
Ch3: Blue
16.7 million additive RGB colors
Static White
4000K
Neutral White
3000K
Warm White
Ch1: White
3000K / 4000K Standard
(2200K, 2700K, 3500K, 5000K, 6500K,
Red, Green, Blue, Amber available1)
Wide
Color Changing (RGBW)
RGBW
Ch1: Red
Ch2: Green
Ch3: Blue
Ch4: White
RGBW (White: 4000K standard)
Color Changing (RGB)
RGB
Ch1: Red
Ch2: Green
Ch3: Blue
16.7 million additive RGB colors
Static White
4000K
Neutral White
3000K
Warm White
Ch1: White
3000K / 4000K Standard
(2200K, 2700K, 3500K, 5000K, 6500K,
Red, Green, Blue, Amber available1)
1. No MOQ required. Please consult regional sales office for pricing and lead time.
2: There is no “Master Dim” channel.

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 10 of 25
2. INSTALLATION
2.1 Points to Consider
Plan your installation before mounting ProPoint Kontour RGB / RGBW / Static White.
The following should be considered for a successful installation:
•Weather conditions and ambient temperature of installation site.
•Installation distances and appropriate cable lengths. Please consult your local Traxon™ office or authorized
agent for necessary aid.
•The number of ProPoint Kontour and Data Injectors and appropriate power sources.
•DMX512 controller to be used to control the ProPoint Kontour.
•Distance between each ProPoint Kontour for thermal expansion.
•Proper surge protection.
•If not beginning installation at the Data Injector, ensure that the layout of the luminaire input and output
connections are in the correct orientation.
2.2 Pre-Installation Checks
2.2.1 Installation Checklist
1. Perform visual check of ProPoint Kontour. Take care not to damage cables/connectors during pre-installation
checks.
2. Prepare cables and all necessary accessories (mounting brackets, temporary waterproof end caps etc).
3. Connect the luminaires, data injectors and power supplies in accordance with the wiring diagram.
4. Report any functional defect found to your nearest Traxon Technologies office. DO NOT attempt to install a
ProPoint Kontour with functional defects on-site.
5. Ensure all pre-installation checks laid out below have been followed.
6. If this installation is to be left in an incomplete state overnight, ensure that all connectors and cables are
properly protected using dust/end caps as required. Any unused materials should be left in an indoor
environment.
a. Ensure that all connected ProPoint Kontour fixtures/data injectors outdoors with an open connector are
secured with an end cap (purchased separately) to keep all ports sealed.
b. Ensure all of the Interconnection Cables, ProPoint Kontour, and Data Injectors are initially stored in a dry
area to guarantee the complete sealing of the system from water before installation.
2.2.2 Cable Bending
Cable bend radius must NOT be less than the Minimum Bending Radius (4 x Cable Diameter) as
specified by cable manufacturer and the Non-Bendable Length of 5cm near the connector end MUST
be adhered to. In addition to the Minimum Bending Radius, ensure that 5cm of cable at the connector
junction is kept straight – see image below:
To reduce stress induced on ProPoint Kontour, please adhere to the Minimum Bending Radius of 50.4
mm (2”) and the Non-Bendable Length of 50.4mm (2”) near the connector. It is recommended to install
lead cables through conduits/trunking.

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 11 of 25
FIG.4: Cable Bending
Minimum Bending Radius Non-Bendable Length
≥ 50mm
50.4mm / 1.98” 50.4mm / 1.98”
2.2.3 Mounting Bracket
FIG.5: Mounting Bracket
58mm / 2.3” (Narrow)
84mm / 3.3” (Wide)
3.3mm / 0.13”
12.8mm / 0.5"
9.5mm / 0.37"
24.5mm / 1"
2.2.4 Installation Sequence
1. Plan for any possible bending of cables (see “2.2.2 Cable Bending”).
2. Measure the correct distances for mounting bracket holes.
3. Connect ProPoint Kontour in the daisy chain manner outlined in the system diagram/wiring
diagram to form a complete chain.
4. Perform a visual check of the complete system to ensure all parts of the system are properly
connected.
5. Perform a functional check (e.g. turn on and off the luminaire) to ensure that all of the luminaires
operate correctly under control.
2.3 On-Site Installation
•DO NOT attempt installation in wet or severe weather conditions.
•DO NOT leave and expose any ProPoint Kontour or Data Injectors unconnected under wet /
dusty / raining or snowing environment.
•IP failure induced by stressed/damaged cables during or after installation will not be covered
under warranty by Traxon Technologies.
•ALWAYS keep the cables protected from sharp objects and ensure no damage is present on
the cable.
•Failure to keep ProPoint Kontour within the operating temperature range of –30°C to +55°C
/ –22°F to +131°F and storage temperature range of –40°C to +80°C / –40°F to +176°F will
invalidate the product’s warranty.

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 12 of 25
2.3.1 Luminaire Interconnections
The ProPoint Kontour was designed to provide a concentrated, even radiance of light over long run lengths,
up to 305m / 1000ft per Data Injector. This design allows for less power feeds, and simplifies installation.
To ensure that there are no voltage drops over the distance of each run, ProPoint Kontour was designed
with a large-diameter cable. While the large-diameter cable ensures no voltage drop, it does limit the
movement of the cable and has special requirements that must be taken into consideration when arranging
the product layout as below:
Please reference figure 8 below on the minimum spacing between luminaires.
Fixture Length: 300mm / 12”
Standard cable length on condition that the spacing is 4mm / 0.16” (Min.)
1200mm / 47.2”
2400mm / 94.5”
15mm / 0.6”
540mm / 21.3”
1500mm / 59”
600mm / 23.6”
15mm / 0.6”
250mm / 9.8”
128.5mm / 5.1”
128.5mm / 5.1”
130mm / 5.1”
145mm / 5.7”
278.5mm / 10.96”
278.5mm / 10.96”
280mm / 11”
295mm / 11.6”
378.5mm / 14.9”
378.5mm / 14.9”
380mm / 15”
395mm / 15.6”
15mm / 0.6”
Interconnection Limitation
• 300mm / 12” Kontour cannot be connected end-to-end with any other Kontour luminaire and achieve the minimum
distance of 4mm / 0.16” spacing between fixtures. See the below chart for the connection limitations.
• If the 300mm / 12” luminaire is required, it must be positioned next to a 1200mm / 48” or 2400mm / 96” luminaire that has
been customized with shortened input/output cables.
Fixture Length: 600mm / 24”, 1200mm / 48”, 2400mm / 96”
Standard cable length on condition that the spacing is 4mm / 0.16” (Min.)
1200mm / 47.2”
2400mm / 94.5”
15mm / 0.6”
540mm / 21.3”
1500mm / 59”
600mm / 23.6”
15mm / 0.6”
250mm / 9.8”
128.5mm / 5.1”
128.5mm / 5.1”
130mm / 5.1”
145mm / 5.7”
278.5mm / 10.96”
278.5mm / 10.96”
280mm / 11”
295mm / 11.6”
378.5mm / 14.9”
378.5mm / 14.9”
380mm / 15”
395mm / 15.6”
15mm / 0.6”
1200mm / 47.2”
2400mm / 94.5”
15mm / 0.6”
540mm / 21.3”
1500mm / 59”
600mm / 23.6”
15mm / 0.6”
250mm / 9.8”
128.5mm / 5.1”
128.5mm / 5.1”
130mm / 5.1”
145mm / 5.7”
278.5mm / 10.96”
278.5mm / 10.96”
280mm / 11”
295mm / 11.6”
378.5mm / 14.9”
378.5mm / 14.9”
380mm / 15”
395mm / 15.6”
15mm / 0.6”
1200mm / 47.2”
2400mm / 94.5”
15mm / 0.6”
540mm / 21.3”
1500mm / 59”
600mm / 23.6”
15mm / 0.6”
250mm / 9.8”
128.5mm / 5.1”
128.5mm / 5.1”
130mm / 5.1”
145mm / 5.7”
278.5mm / 10.96”
278.5mm / 10.96”
280mm / 11”
295mm / 11.6”
378.5mm / 14.9”
378.5mm / 14.9”
380mm / 15”
395mm / 15.6”
15mm / 0.6”
Interconnection Limitation
4mm/0.16”
Minimum spacing for thermal expansion
Power/Data output side Power/Data input side
•600mm / 24”, 1200mm / 48” and 2400mm / 96” Kontour luminaire’s can
be interconnected end-to-end to allow a 4mm / 0.16” spacing.

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 13 of 25
300mm fixture connecting with other length units:
Fixture Wiring
Illustration Possibility Connection description (Ensure the Min. 4mm Spacing) Remarks
300mm / 12”
& 300mm / 12” ×
300mm / 12” Kontour cannot be connected end-to-end
with another 300mm / 12” luminaire to achieve the minimum
distance of 4mm / 0.16” spacing between fixtures.
Min.Space: 65.59mm
300mm / 12”
& 1200mm /48” √
300mm / 12” & 1200mm / 48” Kontour can be connected
end-to-end to achieve the minimum distance of 4mm /
0.16” spacing between fixtures. This however requires a
customized version of the 1200mm / 48” with a shortened
input cable, output cable, or both, depending on project
needs. Min.Space: 94.10mm
300mm / 12”
& 2400mm / 96” √
300mm / 12” & 2400mm / 96” Kontour can be connected
end-to-end to achieve the minimum distance of 4mm /
0.16” spacing between fixtures. This however requires a
customized version of the 2400mm / 96” with a shortened
input cable, output cable, or both, depending on project
needs.
If wiring 1200mm / 48” + 300mm / 12” + 1200mm / 48”, the output cable of Fixture A must be reduced, and the
input cable of Fixture C must be reduced.
288.5mm / 11.4”
90mm / 3.5”
4mm / 0.16”
4mm / 0.16”
70mm / 2.8”
308.5mm / 12.1”
188.5mm / 7.4”
90mm / 3.5”
4mm / 0.16”
4mm / 0.16”
70mm / 2.8”
208.5mm / 8.2”
Power/Data
Output
Power/Data
Input
Power/Data
Output
Power/Data
Input
Fixture B
Fixture D Fixture E
Power/Data
Output
Power/Data
Input
Power/Data
Output
Power/Data
Input
Fixture F
Fixture C
Fixture A
If wiring 2400mm / 96” + 300mm / 12” + 2400mm / 96”, the output cable of Fixture D must be reduced, and the
input cable of Fixture F must be reduced.
288.5mm / 11.4”
90mm / 3.5”
4mm / 0.16”
4mm / 0.16”
70mm / 2.8”
308.5mm / 12.1”
188.5mm / 7.4”
90mm / 3.5”
4mm / 0.16”
4mm / 0.16”
70mm / 2.8”
208.5mm / 8.2”
Power/Data
Output
Power/Data
Input
Power/Data
Output
Power/Data
Input
Fixture B
Fixture D Fixture E
Power/Data
Output
Power/Data
Input
Power/Data
Output
Power/Data
Input
Fixture F
Fixture C
Fixture A
Conclusion:
The customer should work closely with your regional Traxon representative to ensure the product layout meets the
project needs.

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 14 of 25
2.3.2 Mounting Bracket
1. Affix mounting bracket to installation surface with anchor bolts. Anchor bolt head cannot protrude
beyond 3mm above bracket.
FIG.6: Mounting Bracket to Surface
Mount bracket to surface
(hardware not included)
Screw driver type: M3 hex driver
M3 Screw (included)
2. Unplug the dust caps/waterproof end caps and keep them safe for future use.
3. Fully connect all ProPoint Kontour connection cables one after the other and begin from the data
injector. Do not work on the other unit’s connections until the first unit under installation is properly
connected. (see “FIG.7: Connect All ProPoint Kontour”).
FIG.7: Connect All ProPoint Kontour
Power/Data Input side
Power/Data output side
CLICK!
Please refer to the section 2.3.1.
NOTE •Be sure not to compress the IN/OUT cables (see “2.2.2 Cable Bending”).
•To keep LED pitch consistent and allow for thermal expansion, be sure to keep a
minimum distance of 4mm (0.16”) between consecutive ProPoint Kontour (see “FIG.8:
Minimum Distance”).

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 15 of 25
FIG.8: Minimum Distance
4mm/0.16”
Minimum spacing for thermal expansion
Power/Data output side Power/Data input side
4. Attach the terminator end cap on last ProPoint Kontour in run.
2.4 Accessories Installation
Safety Wire Installation Method
1. Affix safety cable eyelet to installation surface with anchor bolts. DO NOT ANCHOR SAFETY
CABLE WITH THE SAME BOLT AS MOUNTING BRACKET!
FIG.9: Safety Cable to Surface
Safety Cable (Optional Accessory) to fixture
φ10.2mm / 0.4”
To surface (hardware not included)
2. Attach safety cable to ProPoint Kontour using the snap clip.
FIG.10: Safety Cable to ProPoint Kontour
Snap-Clip to fixture
φ10.2mm / 0.4”

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 16 of 25
3. SYSTEM CONFIGURATION
3.1 Wiring Diagram
FIG.11: System Wiring Diagram Details
Male connector
ProPoint Linear/Kontour Injector Box
Mains AC 120-277V~ (ETL) Mains AC 220-240V~ (CE)
DMX In
DMX Out
Use provided end cap for final data injector in chain
3-pin Female connector
Female connector
Cable A*
DATA OUT
DATA IN
POWER IN TO FIXTURE
Use Kontour end cap w/Terminator (PP.AC.600000) for final fixture in chain. End cap includes resistor.
Junction Box
Outdoor cable specification: CAT-5e UTP/FTP PVC jacket; UV resistant Outer diameter 6mm/0.24” Filled type
To construct a longer data cable, use outdoor data cable with RJ45 housing.
1. All ordering information of accessories can be referred to next page. 2. All interconnection information can be referred to next page. * Cable A, Cable B: Please refer to ProPoint Kontour Wiring Diagram P.2 for options.
PP.AC.400000 ProPoint RJ45 Field Install Connectors (pair)
Cable B*

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 17 of 25
Wiring Information Details
ProPoint Kontour Narrow-CE
Model Power Consumption (Typ.) Input Voltage Max Connected Chain
300mm / 12” 4W 220-240V 512
600mm / 24” 8W 220-240V 400
1200mm / 48” 16W 220-240V 200
2400mm / 96” 32W 220-240V 100
ProPoint Kontour Narrow-ETL
120V
Model Power Consumption (Typ.) Input Voltage Max Connected Chain
300mm / 12” 4W 120V 432
600mm / 24” 8W 120V 216
1200mm / 48” 16W 120V 108
2400mm / 96” 32W 120V 54
277V
Model Power Consumption (Typ.) Input Voltage Max Connected Chain
300mm / 12” 4W 277V 512
600mm / 24” 8W 277V 500
1200mm / 48” 16W 277V 250
2400mm / 96” 32W 277V 125
ProPoint Kontour Wide-CE
Model Power Consumption (Typ.) Input Voltage Max Connected Chain
300mm / 12” 5W 220-240V 512
600mm / 24” 10W 220-240V 320
1200mm / 48” 20W 220-240V 150
2400mm / 96” 40W 220-240V 80
ProPoint Kontour Wide-ETL
120V
Model Power Consumption (Typ.) Input Voltage Max Connected Chain
300mm / 12” 5W 120V 344
600mm / 24” 10W 120V 172
1200mm / 48” 20W 120V 86
2400mm / 96” 40W 120V 43
277V
Model Power Consumption (Typ.) Input Voltage Max Connected Chain
300mm / 12” 5W 277V 512
600mm / 24” 10W 277V 400
1200mm / 48” 20W 277V 200
2400mm / 96” 40W 277V 100

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 18 of 25
Accessories (ETL / CE)
Model No. Description Item Code
PP.AC.100001 PROPOINT LINEAR/KONTOUR INJECTOR BOX AM374890055
PP.AC.100002 PROPOINT LINEAR/KONTOUR INJECTOR BOX BL AM374900055
PP.AC.100003 PROPOINT LINEAR/KONTOUR INJECTOR BOX WT AM374910055
PP.AC.600000 PP LIN/KON END CAP W/ TERM. AM380550055
PP.AC.400000 PROPOINT RJ45 FIELD INSTALL CONNECTORS (PAIR) AM380560055
Accessories (CE)
Cable Type Model No. Description Item Code
Cable A* PP. A2.303000 3M PP LINEAR POWER INPUT CABLE CE AM374840055
Cable B* KO.KB.610000 10M KONTOUR PWR/DATA INT CBL CE AM357520155
Cable B* KO.KB.601000 1M KONTOUR PWR/DATA INT CBL CE AM357490155
Cable B* KO.KB.602000 2M KONTOUR PWR/DATA INT CBL CE AM357500155
Cable B* KO.KB.603000 3M KONTOUR PWR/DATA INT CBL CE AM357510155
Accessories (ETL)
Cable Type Model No. Description Item Code
Cable A* PP. A1.303000 3M PP LINEAR POWER INPUT CABLE ETL AM374840155
Cable B* KO.KA.610000 10M KONTOUR PWR/DATA INT CBL ETL AM357520055
Cable B* KO.KA.601000 1M KONTOUR PWR/DATA INT CBL ETL AM357490055
Cable B* KO.KA.602000 2M KONTOUR PWR/DATA INT CBL ETL AM357500055
Cable B* KO.KA.603000 3M KONTOUR PWR/DATA INT CBL ETL AM357510055
* All cables come pre-wired with male / female connectors.
3.2 Luminaire Addressing and Control
3.2.1 Luminaire Control
Standard configuration is set to control every 12” / 300mm. The pixel configuration can be set at the
factory to those listed in the table below:
Model Length Available PXL Configuration
ProPoint Kontour Narrow
300mm / 12”
•300mm can be 1PXL
•600mm can be 1PXL or 2PXL
•1200mm can be 1PXL, 2PXL, or 4PXL
•2400mm can be 1PXL, 2PXL, 4PXL, or 8PXL
•PXL Configuration is set during manufacturing, and is not adjustable on-siteL
600mm / 24”
1200mm / 48”
2400mm / 96”
ProPoint Kontour Wide
300mm / 12”
600mm / 24”
1200mm / 48”
2400mm / 96”

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 19 of 25
3.2.2 Luminaire Addressing and Control
The ProPoint Kontour Narrow and Wide utilize 3 DMX channels for RGB, 4 DMX channels for RGBW and 1 DMX
channel for Static White per Pixel.
The ProPoint Kontour is shipped with a default DMX address of 001.
The ProPoint Kontour benefits from an auto-addressing functionality to simplify the setup and commissioning of
the project:
•On startup, the ProPoint Data Injector automatically senses all Kontour luminaire’s connected to it.
•The ProPoint Data Injector automatically addresses each luminaire, starting at the first unit closest to the Data
Injector.
•Each Data Injector consumes 512 DMX channels regardless of connected fixture count. Maximum number of
Data Injector units per DMX-512 universe depends on number of fixtures per Data Injector.
•Any standard DMX output device can be utilized with Kontour.
•Using the DMX Out from the ProPoint Data Injector to the DMX In of another ProPoint Data Injector will repeat
the signal. The ProPoint Data Injector cannot sense the address of the last fixture of the previous Data Injector
and continue the next address.
ProPoint Power-Up and Loss of Data Behavior
The ProPoint Kontour will exhibit the following behavior upon power-up and loss of DMX data:
Power-Up with no DMX data present Luminaire will illuminate at full power
Power-Up with DMX data present Luminaire will respond based on the DMX values being received
Loss of DMX data Luminaire will hold the last valid DMX values received until a power cycle or
until DMX is restored.
DMX Channel Functions
RGBW Unit
DMX Channel Function
1Red Intensity
2Green Intensity
3Blue Intensity
4White Intensity
RGB Unit
DMX Channel Function
1Red Intensity
2Green Intensity
3Blue Intensity
White Unit
DMX Channel Function
1White Intensity

www.traxontechnologies.com | www.osram.us/traxon
©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide IG0110EN V1.0 12/20 P. 20 of 25
4. CARE AND MAINTENANCE
•Traxon™ products are of superior design and quality and should be treated with care. The recommendations
below will help fulfill any warranty obligations and gain good use and longevity from the products.
•Do not attempt or use the product(s) until you read and understand the installation instructions. Failure to
adhere to these instructions could result in serious injury or property damage.
•Do not use product(s) if cables are damaged.
•Do not connect cables and connectors when wet or in wet area. Moisture on bare connectors can cause
electric shock and damage to product(s).
•Do not use product(s) in extreme heat environment. Ensure there is sufficient airflow and use cool air circulation
if required.
•Do not drop, knock, or shake product(s). Rough handling can damage the electronics and void the warranty.
•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean products. Wipe with a damp cloth
on housings and a dry cloth on electronics to remove dirt or dust.
•Do not attempt to service or repair the product(s) unless done by an authorized service personnel. Contact your
local Traxon office or distributor for details.
•If the product is not working as specified, please contact your nearest authorized service center or Traxon
Technologies office for assistance.