Osram BY-P28 User manual

BY-P28 Waterproof Par Light
1pc 200W COB 4in1 +12pcs 12W RGBW led
User manual
P le ase rea d t he ins t r u ction s ca refu ll y before use

2
TABLE OF CONTENTS
1. Safety Instructions ...........................................................................3-4
2. Technical Specification ......................................................................5
3. Menu Function................................................................................5-6
4. DMX Channel List ......................................................................... 7--8
5. Attention ..........................................................................................9
6. Fixture Cleaning ...............................................................................9
statement
Fixtures should be fastened on the hooks with screws. Make sure the
installation is secure to prevent chattering and slipping during operation. Also
make sure that the structure of the connected luminaire can support the
luminaire 10 times the weight. At the same time, when installing the lamps,
they also use a safety rope to support the weight of the lamps by 12 times.
The installation of the equipment should be carried out by professionals, and it
should also be installed in places where people can't reach them casually or
where no one is free to pass by.

3
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using
the unit.
Before operating, ensure that the voltage and frequency of power
supply match the power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order
to avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at
least 50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating
as it is fire hazard.
Use safety cable when fixes this unit. DO NOT handle the unit by taking its head
only, but always by taking its base.
Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hand during its operation. Turn off the power
and allow about 15 minutes for the unit to cool down before replacing or serving.
In the event of serious operating problem, stop using the unit
immediately.Never try to repair the unit by yourself. Repairs carried out by
unskilled people can lead to damage or malfunction. Please contact the

4
nearest authorized technical assistance center. Always use the same type
spare parts.
DO NOT touch any wire during operation as high voltage might be causing
electric shock.
Warning:
To prevent or reduce the risk of electrical shock or fire, do not expose the unit
to rain or moisture.
DO NOT open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced
if they are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure
that the unit is firmly fixed to avoid vibration and slipping while
operating. And make sure that the structure to which you are attaching the
unit is secure and is able to support a weight of 10 times of the unit’s weight.
Also always use a safety cable that can hold 12 times of the weight of the unit
when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people.

5
2. Technical Specifications
Light source: 1pc 200W COB 4in1rgbw +12pcs 12W RGBW led
● power consumption: 350w
● Input voltage: AC100-260V ,50-60Hz
● Beam angle: COB LED 55°， 12W LED 25°
Control
● Control Mode: DMX512 / Self-propelled
● COB rgbw 4in1+RGBW ：10/14 channels
Construction
● IP rate: IP65
● Display: 180°reversible LCD display
● dimension: 29*28*22cm
● Net weight: 6.5kgs
● Gross weight: 7kgs
Accessories
● Signal line: 3-pin 1 piece
● Power cord: 1 piece
● Chinese/English manual: 1 piece

6
3.Lux Date
4.Menu Function:

7
1.Menu: COB 4in1 rgbw +RGBW
1.Master
1.Master
2.Alone
2.Mic Sense
Sound sensitive adjust 001--100
3.Channel Value
10CH
6CH
4.Inform
1.Temperature - ℃
2.Soft V1.0
5.Default
Yes
Factory reset
No
6.Address
Set address 001--512
7.Display
1.Forward
2.Reverse
8.Manual
1.Dimmer R1
0-255
2.Dimmer G1
3.Dimmer B1
4.Dimmer W1
5.Dimmer R2
6.Dimmer G2
7.Dimmer B2
8.Dimmer W2
9.Strobe
9.Mode
1.DMX 512
2.Sound
3.Auto 1 fast to slow
Color changes
4.Auto 2 fast to slow
Color Fade
10.Channels
10CH
14CH

8
5.DMX Channel List:
A001- 10CH model
10 CH
Function
Number
Description
1
Dimmer
0-255
Dark to bright
2
Strobe
NO
0-15
Strobe (slow to
fast)
16----214
Random strobe
215----255
3
COB R
dark to bright
0----255
4
COB G
5
COB B
6
COB W
7
Red of par
8
Green of par
9
Blue of par
10
White of par

9
A002- 14CH model
14CH
Function
Number
Description
1
Dimmer
0-255
Dark to bright
2
Dimming mode
Mode 1
0----49
Mode 2
50-199
Mode 3
100-149
Mode 4
150----255
3
Strobe
NO
0-15
Strobe (slow to
fast)
16----214
Random strobe
215----255
4
COB R
dark to bright
0----255
5
COB G
6
COB B
7
COB W
8
Red of par
9
Green of par
10
Blue pf par
11
White pf par
12
rainbow
13
Dynamic color
NO
0---49
Jump
50----99
Gradient
100--255
14
Control channel
From fast to slow
0----255

10
6. Attention:
1. When the lamp is lit after the lamp is powered on, the light emitted by the lamp bead should
be avoided as much as possible.
2. When loading or unloading the lamp, be sure to cut off the main power supply connected to
the device before you can open the cover on which the lamp bead is installed.
7. Fixture Cleaning
The outside of the lens must always be wiped so that the lighting effect is better.
Wipe the frequency of the environment. Humidity, excessive smoke, and a
particularly dirty environment can make the lens dusty.
● Use a soft cloth and special glass cleaner.
● Wipe the exterior of the lens at least every 30 days.
● Use vacuum cleaners or air guns inside the luminaire and clean it at least twice
a year.