oventrop Aktor M Manual

2017 Oventrop 1
“Aktor M”
Electromotive actuators
Tender specication:
Oventrop electromotive actuators for steady control. The actuator
can be used for two point, three point or proportional control
(0-10 V), with squeeze connection and position feedback signal
0-10 V.
Models: Item no.:
24 V, steady control with 0-10 V 1158010
or switching as two or three point control.
Type of characteristic line
(linear, equal percentage) adjustable.
With enclosed adapter for Oventrop valves.
Same actuator as item no. 1158010 1158011
but without enclosed adapter
Technical data:
Operating current: 24 V ~/=
Power consumption: 4.9 W during operation
 8.7Winnalliftposition
Drive: 0 - 10 V
Max. piston stroke: 10 mm
Operating power: 500 N
Floating time: 7.5 / 15 s / mm
Protection: IP 54 according to EN 60529
Max.uidtemperature: 120°C
Ambienttemperature: -10°Cupto+55°C
Storagetemperature: -10°Cupto+55°C
Connectingcable: 5x0.5mm²
Installation:
The connecting cable must not come into contact with the hot pipe
as excessive heat will accelerate the ageing of the cable insulation.
Electrical connection must be carried out in accordance with the
requirements of the local Electricity Board.
The Oventrop electromotive actuators can be installed in any
position, except for vertical downward position.
Depending on the wiring (see connection diagrams), the actuators
item no. 1158010/11 can be used as two point, three point or
0-10 V actuator.
Application:
The actuators can be combined with the following Oventrop
valves:
Item no. 1158010:
“CoconQTR/QFC”DN40andDN50
Item no. 1158011:
Two-way valves item no. 11308.. and 16708 DN 15-DN 50
Function:
– Synchronous motor with activation and switch off technology
– Electronic recognition of the limit of travel via timer
– Maintenance-free gear with magnetic coupling
– Gear release for manual positioning of the valve. To do so,
activate the lateral sliding switch and set the actuator to the
required position with the help of the enclosed key.
P
M
24 V~/=
MM 0201
A/D
05
y=0...10V
y0=0...10V
03
BU BK BN RD GY
MM 02
01 0503
24 V~/=
open/stop/close
Variante 1 (3pt)
24 V~/=
open / close
Variante 2 (2pt)
50MM03
BU RD GY
BU BK BN RD GY
02
01
BK BN
Variante 3 (0-10 V)
Connectiondiagramsitemno.1158010/11
Dimensions with mounted adapter
Technical information
157
35
122
126.5
63
43.5
Actuator
Adapter
Variant 1 (3pt)
Variant 2 (2pt)
Variant 3 (0-10 V)

2 2017 Oventrop
“Aktor M”
Electromotive actuators
Tender specication:
Oventrop electromotive actuators for steady control. The actuator
can be used for two point, three point or proportional control, with
squeeze connection and position feedback signal 0-10 V.
1158020: 0(2)..10 V=
1158021/22: 0(2)..10 V= or 0(4)..20 mA
With enclosed adapter for Oventrop valves.
Models: Item no.:
24 V, steady control with 0(2)-10 V 1158020
or switching as three point control.
Linear characteristic line.
24 V, steady control with 0(2)-10 V or 0(4)-20 mA 1158021
or switching as two or three point control.
Linear characteristic line.
With spring return.
Valves opening with current “off”.
24 V, steady control with 0(2)-10 V or 0(4)-20 mA 1158022
or switching as two or three point control.
Linear characteristic line.
With spring return.
Valves closing with current “off”.
Technical data:
Item no. 1158020:
Operating current: 24 V ~; 50/60 Hz
Power consumption: 4.8 W during operation and in
nalliftposition
Drive: 0 (2)– 10 V
Max. piston stroke: 20 mm
Operating power: 800 N
Floating time: 9 s / mm
Protection: IP 54 according to EN 60529
Max.uidtemperature: 120°C
Ambienttemperature: 0upto50°C
Storagetemperature: 0upto50°C
Actuator:
reversible synchronous motor
Item no. 1158021/22:
Operating current: 24 V ~; 50/60 Hz
Power consumption: 26 W during operation and in
nalliftposition
Drive: 0(2) – 10 V or 0(4) – 20 mA
Max. piston stroke: 20 mm
Operating power: 1000 N
Floating time: 2 s / mm
Emergency setting time: 1 s / mm
Protection: IP 54 according to EN 60529
Max.uidtemperature: 120°C
Ambienttemperature: 0upto50°C
Storagetemperature: 0upto50°C
Actuator:
brushless direct current motor
Installation:
The connecting cable must not come into contact with the hot pipe
as excessive heat will accelerate the ageing of the cable insulation.
Electrical connection must be carried out in accordance with the
requirements of the local Electricity Board.
The Oventrop electromotive actuators can be installed in any
position, except for vertical downward position.
Depending on the wiring (see connection diagrams), the actuators
item no. 1158020/21/22 can be used as two point, three point or
0(2)-10V or 0(4)- 20 mA actuator.
Dimensions of actuators and connections sizes of adapter
Item no. 1158020 and adapter
Item no. 1158021/22 and adapter

„Aktor M“
Elektromotorische Stellantriebe
2017 Oventrop 3
Application:
The actuators can be combined with the following Oventrop
valves:
“CoconQTR/QFC“DN40uptoDN100
Function:
– electronic switching operation depending on the motive force
– compensation of external interferences by dynamic hysteresis
– linear characteristic line
– valve blocking function, short stroke lift if the actuator has not
moved within 24 h (optionally adjustable)
– automatic piston stroke adaptation by initialization
– manual setting of item numbers 1158021/22 by removing the
cover and by setting the actuator to the required position with
the help of a 4 mm Allen key
– maintenance-free
LED display:
Item no. 1158020:
Permanent light: Normal operation
Slowashing: Initializationrunorpartialinitialization
after power failure
Irregularfastashing: Valveisblockedormanualsetting
Off: Power supply interrupted or actuator
fuse defective
Item no. 1158021/22:
Permanent light: Normal operation
Shortashing: Malfunction/reversepolarity
Longashing: Initializationrun Connectiondiagramsitemno.1158020
Connectiondiagramsitemno.1158021/22
(steady)
(2pt)
(3pt)
1 = On
2 = Stop
3=Closed
24VAC
OVAC/DC
1 3
Priority for 2pt & 3pt: “Drive stem closing down“
(steady)
(2pt)
(3pt)
24VAC
OVAC/DC
1 32

Tender specication:
Oventrop electromotive actuators for steady control. The actuator
can be used for two point, three point or proportional control
(0-10 V or 4-20 mA), with squeeze connection and position feed-
back signal 0-10 V.
With enclosed adapter for Oventrop valves.
Models: Item no.:
24 V, steady control with 0-10 V or 4-20 mA 1158030
or switching as to or three point control.
Type of characteristic line (linear, square-law,
equal percentage) adjustable.
24 V, steady control with 0-10 V or 4-20 mA 1158031
or switching as to or three point control.
Type of characteristic line (linear, square-law,
equal percentage) adjustable.
With spring return.
Valves opening with current “off”
24 V, steady control with 0-10 V or 4-20 mA 1158032
or switching as to or three point control.
Type of characteristic line (linear, square-law,
equal percentage) adjustable.
With spring return.
Valves closing with current “off”
Technical data:
Item no. 1158030:
Operating current: 24 V ~/=
Power consumption: 10 W during operation
18Winnalliftposition
Drive: 0-10 V or 4-20 mA
Max. piston stroke: 40 mm
Operating power: 2500 N
Floating time: 2 / 4 / 6 s / mm
Protection: IP 66 according to EN 60529
Max.uidtemperature: 120°C
Ambienttemperature: -10°Cupto+55°C
Storagetemperature: -10°Cupto+55°C
Item no. 1158031/32:
Operating current: 24 V ~/=
Power consumption: 10 W during operation
20Winnalliftposition
Drive: 0-10 V or 4-20 mA
Max. piston stroke: 40 mm
Operating power: 2000 N
Floating time: 2 / 4 / 6 s / mm
Protection: IP 66 according to EN 60529
Max.uidtemperature: 120°C
Ambienttemperature: -10°Cupto+55°C
Storagetemperature: -10°Cupto+55°C
Number of spring returns: > 4000
Installation:
The connecting cable must not come into contact with the hot pipe
as excessive heat will accelerate the ageing of the cable insulation.
Electrical connection must be carried out in accordance with the
requirements of the local Electricity Board.
The Oventrop electromotive actuators can be installed in any
position, except for vertical downward position.
Depending on the wiring (see connection diagrams), the actuators
item no. 1158030/31/32 can be used as two point, three point or
0-10 V or 4-20 mA actuator.
Dimensions of actuators and connection sizes of adapter
4 2017 Oventrop
“Aktor M”
Electromotive actuators
Actuator and adapter
230 60 57 18.5
Ø 44
64
90
30
289
136

2017 Oventrop 5
Application:
The actuators can be combined with the following Oventrop
valves:
“CoconQFC”DN125uptoDN200
Two-way valves item no. 11308.. and 16708.. DN 65 up to DN 150
Function:
– electronic switching operation depending on the motive force
– automatic recognition of the input control signal
– setting of the characteristic line at the actuator (linear, square-
law, equal percentage)
– automatic adaptation
– free choice of mode of operation
– choice of characteristic line
–settingofoatingtimeviacodingswitch
– the actuator can be set manually with the crank handle
– reinitialization is triggered with the crank handle
LED display:
BothLEDsashred: Initialization
OneLEDashesgreen:Apistonstrokeiscarriedoutbythe
actuator, direction according to LED
One LED glows green: Idle position, last direction of travel
according to LED
One LED glows red: Final position, valve position according
to LED
Off: No power supply or no activation in
three point mode
Accessories:
Connectionmodule230V 1158033
For the connection of the 24 V actuators “Aktor M”, item no.
1158030/31/32 to the 230 V supply voltage.
Module for plug-in connection to the actuator.
“Aktor M”
Electromotive actuators
Subjecttotechnicalmodicationswithoutnotice.
Product range 3
ti 315-EN/10/MW Gedruckt auf chlorfrei
Edition 2017 gebleichtem Papier.
Connectiondiagramsitemno.1158031/32
100%
0%
100%
Stem
24V~/=24V~/=
24V~/=
2pt 3pt
Steady
On
Off
S1 S2 S3 S4
S1, S2 = Floating time
S3, S4 = Type of characteristic line
21 1 2a 2b 3u
y = 0…10V y = 4…20mA y0 = 0…10V
3i 44
20mA 10V10V
100% 4mA 10VOV
1158031 1158032
0% 10V 20mA OV
0% OV
3u 3i 44
4mA OV
2a
2b
100% 0%
2pt, 3pt, steady
21
21 1 2a 2b 3u3i 44 21 1 2a 2b 3u3i 44
Connectiondiagramsitemno.1158030
100%
0%
100%
Stem
24V~/=24V~/=
24V~/=
2pt 3pt
Steady
On
Off
S1 S2 S3 S4
S1, S2 = Floating time
S3, S4 = Type of characteristic line
1 2a 2b 3u
y = 0…10V y = 4…20mA y0 = 0…10V
3i 44
20mA 10V10V
100% 4mA 10VOV
0% 10V 20mA OV
0% OV
3u 3i 44
4mA OV
2a
2b
1 2a 2b 3u3i 44 1 2a 2b 3u3i 44

3.38 2017 Oventrop