ParaBody 778 User manual

1
778 LEG PRESS ADAPTER KIT
FOR 777 GYM SYSTEM
CLASSH
PART # 7031501
REV. B
Version: 778101
Revision: 02/28/01
USER’S GUIDE
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
j
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
IMPORTANT SAFETY INFORMATION
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Gym Layout.....................4
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 Life Fitness, a division of Brunswick Corporation. All rights reserved.
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
Parts list..........................5
Assembly Instructions.....5-13
General Maintenance.......14
Warranty Statement..........15
Product Services..............16
Insert-Registration Card
©

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the ParaBody 778 LEG PRESSADAPTER KIT. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* 9/16” wrench
* Ratchet with 9/16” sockets
* Adjustable wrench
* Tape measure
3
NOTE:BOLTLENGTH IS MEASURED FROMTHEUNDERSIDE OFTHEHEADOFTHEBOLT.
BOLT LENGTH RULER:
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH

4
Minimum Required Usable Space
Length = 90 inches (229 cm) 7’ 6”
Width = 103 inches (262 cm) 8’ 7”
Height = 84 inches (213.5 cm) 7”
1 Square = 1’ X 1’
Length = 90 inches (229 cm) 7’ 6”
Width = 130 inches (330 cm) 10’ 10”
9’1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’
1’
6’
5’
4’
3’
2’
Dimensions Including Leg Press (optional)
7’
8’
9’

PARTS LIST
5
PART #
7031308
7006708
6987802
7031701
3116201
6467001
KEY
1
2
3
4
5
6
QTY
1
1
1
1
1
2
PART #
3102501
3102802
3102924
3102904
3102935
DESCRIPTION
3/8” WASHER
3/8” LOCKNUT
3/8 X 1-3/4” BOLT
3/8 X 3” BOLT
3/8 X 4-1/2” BOLT
QTY
9
5
2
2
2
DESCRIPTION
FRONT LEG
PULLEYBRACKET
WEIGHTSTACK CABLE
LEG PRESS CABLE
3-1/2” PULLEY
2” COVER CAP
KEY
7
8
9
10
11
NOTE: The LEG PRESS ATTACHMENT (100101) must be assembled before
connecting it to the PARABODY 777 GYM SYSTEM
FIGURE 1
STEP 1:
• Remove the WEIGHT STACK CABLE as shown in FIGURE 1. Discard the cable.
WEIGHTSTACK
CABLE

6
FIGURE 2
STEP 2:
• Route the 120” CABLE (3) around the pulley in the BOOM PLATES as shown in FIGURE 2. (NOTE: Make sure the cable
runs in the grooves of the pulleys.)
• Assemble one 3-1/2” PULLEY (5) to the PULLEY BRACKET (2) using one 3/8 X 1-3/4” BOLT (9) and one 3/8” LOCK NUT
(8) (Note: Loop the 120” CABLE around the PULLEY prior to assembling the PULLEY BRACKET.)
• Screw the long threaded end of the new WEIGHT STACK CABLE (3) into the end of the WEIGHT PLATE SHAFT. See
FIGURE 2.
• Screw the short threaded end of the WEIGHT STACK CABLE (3) into the end of the PULLEY BRACKET (2) .See FIGURE 2.
8
3
5
2
3/8 X 1-3/4” 9

FIGURE 3
STEP3
• Slide two 2” SQ. COVER CAPS (6) over the FRONT LEG (1) as shown in FIGURE 3.
1
6
7
FIGURE 4
STEP 4:
• Remove the 3/8 X 3-3/4” BOLT and 3/8” LOCK NUT from the BASE PLATE as shown in FIGURE 4.
3/8” LOCKNUT
3/8 X 3-3/4” BOLT

8
FIGURE 5
STEP 5:
• SECURELY assemble the FRONT LEG (1) to the 777 Gym System using two 3/8 X 4-1/2” BOLTS (11), five 3/8” WASHERS
(7), one previously removed 3/8” LOCK NUT and one 3/8” LOCK NUT (8) as shown in FIGURE 5.
1
8
7
11 3/8 X 4-1/2”

9
FIGURE 6
STEP6
• Remove one existing 3-1/2” PULLEY, two
WASHERS, two 2” WHEELS and two SPACERS
from the ADJUSTMENT TUBE on the 100 LEG
PRESS OPTION by unfastening the 3/8 X 4-1/2”
BOLT holding the pulley on. See FIGURE 6.
(NOTE: The pulley will be used in STEP 9.)
3-1/2” PULLEY
2” WHEEL
3/8 X 4-1/2”
BOLT
SPACER
FIGURE 7
STEP7
• Assemble the LEG PRESS CABLE (4) to the ADJUSTMENT TUBE on the 100 LEG PRESS using the existing previously
removed 3/8 X 4-1/2” BOLT, SPACERS, WASHERS, 2” WHEELS AND NUT. (Note: Do not overtighten! Tighten only until
nut is completely on bolt.) See FIGURE 7.
2” WHEEL
3/8 X 4-1/2” BOLT
NUT
WASHER
SPACER
4
DONOT
OVERTIGHTEN!

10
FIGURE 8
STEP8
• Securely fasten the 100 LEG PRESS to the FRONT LEG (1) using two 3/8 X 3” BOLTS (10), four 3/8” WASHERS (7), and two
3/8” LOCK NUTS (8) as shown in FIGURE 8.
4
7
1
8
100 LEG PRESS
10 3/8 X 3”