ParaBody 813102 User manual

Serious
813102 VKR/CHIN/DIP
ASSEMBLY INSTRUCTIONS
Part# 6812201 Revision:01/17/00

[IMPORTANT NOTES]
WELCOMETO THEWORLDOF
Please note:
*Thankyou for purchasing the Parabody813102VKRJCHIN/DIP.Please read these
instructions thoroughlyandkeep themfor future reference. This product mustbe assembled
¯ ona flat, level surfacetoassureits properfunction..
* Werecommendcleaningyour product (pads and frame) oI~ a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfromyour Parabodycustomerservice representative
at [phone].
Thereis a risk assumedby individuals whouse this type of equipment.Tominimizerisk, please
followthese rules:
1. Inspect equipmentdaily. Tightenall loose connectionsand. replace wornparts immediately.
Failureto doso mayresult in seriousinjury.
2. Donot allow minorsor children to play on or aroundthis equipment.
3. Exercisewithcare to avoidinjury.
4. If unsureof properuse of equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
! ToolsRequired for Assembly]
* 9/16" wrench
* Ratchetwith 9/16" socket
* Adjustable wrench
* Hammer
* Tape measure
Bolt LengthRuler I
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSI~E OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER: BOLT LENGTH
3 4 56
012I , I I I [ I ,

PART# DESCRIPTION
16102303 BASE CONNECTOR
2 6480003 " CHINBAR
36480503 : ...... VKRSIDE
4 6480903 UPPERBACKSUPPORT
¯5 6665902 - BACKPAD
66752702 ARM PAD
7 3102501 3/8" FLAT WASHER
83102601 3/8" LOCKWASHER
1
2
34
6
PART#
29 3102802
1 10 3102904
211 3103101
12 3103103
"13
14
15
6236701
6405201
6467001
DESCR1FHON
3/8" LOCKNUT 14
3/8 X 3" BOLT 20
1-1/4X5" GRIP 2
1-1/4X7’ ChTdP 6
1-3/4" SQ. ENDCAP 1
2" SQ. ENDCAP 4
2" SQ. COVERCAP 4
FIGURE 1
STEP1:
¯ Insert four 2" SQ.COVERCAPS(15) into the endsof the VKRSIDES(3) as shownin FIGURE
¯ Insert four 2" SQ.ENDCAPS(14) into the the endsof the VKRSIDES(3) as shownin FIGURE
3

.~3/8 X 3"
FIGURE 2
STEP 2:
~3/8X3"
¯LOOSELYassemble the UPPERBACKSUPPORT(4) to the VKRSIDES’, (3) using two 3/8 X3" BOLTS(10),
four 3/8" FLATWASHERS(7), and two 3/8" LOCKNUTS(9) as shownin FIGURE
¯LOOSELYassemble the two BASECONNECTORS(1) to the VKRSIDE~g(3) using eight 3/8 X3" BOLTS(10),
sixteen 3/8" FLATWASHERS(7), and eight 3/8" LOCKNUTS(9) as shownin FIGURE
¯ Insert one 2" SQENDCAP(14) into the the end of the UPPERBACKSU-PPORT(4) as shownin FIGURE
I 1/2 [ 1,2 [ 1/2 [ 1/2 I1/2 I 1/2 I
012 3 456
4

FIGURE 3
STEP3:
¯LOOSELYassemble the CHINBAR(2) to the VKRSIDES(3) using two 3/8 X 3" BOLTS(10), four 3/8"
WASHERS(7), and two 3/8" LOCKNUTS.
¯ SECURELYtigten all connections madeup to this point.

FIGURE 4 //
STEP4:
SECURELYattachtwoARMPADS(6) to the VKRSIDES(3) usingfour3/8 X3" BOLTS(10), four 3/8"
WASHERS(8), andfour3/8" FLATWASHERS(7) as shownin FIGURE4. (NOTE:Place the highside of A1LM
PADtowardthe outside.)
1/2 I1/2 I 1/2 I1/2 I1/2 ] 1/2 I
123456

3/8 X3"
FIGURE 5
STEP 5:
¯SECURELYassemble the BACKPAD(5) to the UPPERBACKSUPPOI~.T(4) using two 3/8 X 3" BOLTS(1
two 3/8" LOCKWASHEP~S(8), two 3/8" FLATWASHERS(7) as shown in FIGUR~

FIGURE 6
STEP 6:
¯Slide six 1-1/4 X7" HANDLES(12) over the HANDLESof the VKRSIDES(4) and the CHINBAR(2) as
in FIGURE6.
¯Slide two 1-1/4 X 5" HANDLES(11) over the ARMPADHANDLES ofthe VKRS IDES(4) as shown
FIGURE6. (NOTE:Rubbingalcohol can be used on the inside of the grips to makethemslide on easier.)
Thank you for purchasing the Parabody 884101 SAFTEYRAILATTACI~IENT.If unsure ofproper use of
equipment,call your local Parabodydistributor or call the Parabodycustomerservice departmentat
[phone].
012 3 4 5 6
$