ParaBody 835102 User manual

Serious Steel
835102 HIP SLED
ASSEMBLY INSTRUCTIONS
II I
Part # 6754601 1 Revision:5/24/00

I IMPORTANTNOT,ES
I
WELCOMETO THE WORLDOF ~l~iOU$ ~t~t~.
~
Please note:
* Thankyoufor purchasingthe Parabody835102HIPSLED.Please read these instructions
thoroughlyandkeepthemfor future reference. Thisproduct mustbe assembledona flat, level
surfaceto assureits properfunction.
* Werecommendcleaning your product (pads and frame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfromyour Parabodycustomerservice representative
at [phone].
Thereis a risk assumedby individuals whouse this type of equipment.Tominimizerisk, please
followthese rules:
1. Inspect equipmentdaily. Tightenall loose connectionsand replace wornparts immediately.
Failureto doso mayresult in seriousinjury.
2. Donot allow minorsor children to play on or aroundthis equipment.
3. Exercisewithcare to avoidinjury.
4. If unsureof properuseof equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
5. Consulta physicianbefore beginningany exercise program.
I Tools Requiredfor AssemblyI
* 3/4" wrench
* 9/16" wrench
*Ratchetwith3/4" and9/16’" sockets
* Adjustable wrench
* Tape measure
Bolt LengthRuler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
,
BOLT LENGTIt I
BOLT LENGTH RULER:
2

KEY
1
2
4
5
6
7
8
9
10
11
14
15.
16
17
18
19
2O
21
22
23
24
PART# DES CRIPTION
6504903 ~3ASE
6506803’~ PLATFORMSLEEVE
6507403 PAD SUPPORT
6507703 RIGHT HANI~L~’
6507803 LEFT HANDLE
6505403 REARUPRIGI2IT......
6505902 CARRIAGESTOP BAR
6504103 LE~T RAIL
6504203 RIGHTRAIL
6504402 FOOT PLATE
6504702 PLATFORM
6506602
650~002 PLATFORMADJUSTMENT WEIGHT SUPPORT
6521202 ADJ. WHEELBRACKET
6534302 PAD STOP
6501402 CARRIAGE
6509201 SHOULDERPAD
6666901 SEAT PAD
6667301 BACKPAD
6500501 3" DIA. WHEEL
6500601 2" DIA. WI~EL
3103’104 1 X’5" GRIP
3116001 1-1/4" SQ. RUBBERBUM~ER
PARTSLIST
125
1 26
2 27
128
1 29
130
2 31
132
133
1 34
135
1 36
137
238
1 39
140
2 ’41"
142’
143
4 ’44’
4 45
246
2 47
2
PART# DES CRIPTION
6270501 4 X 14" NON-SKIDSTRIP
6405201
6416601
6467001
3102501
3102601
1102802
3102502
3102801
3102804
3102’~09
2" SQ. ENDCAP
1-1/2" X3/4" PARAGLIDE
2" SQ. COVERCAP
3/8" WASHER
3/8" LOCKWASHER
3/8" LOCKNUT
1/2" WASHER
1/2" LOCKNUT
1/2" LOWHEIGHTLOCKNUT
3/8 X 1" BOLT
3102933 3/8 X 2" BOLT
3102904 ’ ’~/8- X3"BOLT
3102935 3/8 X4-1/2" BOLT
3202101 1/2 X1-1/4" BOLT
3102953 1/2 X2-3/4" BOLT’
3102918 1/2 X3-1/4" BOLT
3102917 1/2 X 4" BOLT
3102937 1/2 X4-1/2" BO’LT
~ 102944 i/2 X 5" BOLT
3110002 1-1/4" ROLLPIN
6020601 1/2" FLANGE’BEARII~G’
6466901 1/2" DIA. SPRINGPIN
1
8
1
2
24
8
8
32
14
8
2
4
8
2
’2
2
6
2
8
2
2
8
2

FIGURE 1
X3-1/4"
STEP1:
¯Insert two 2" SQ.ENDCAPS(26) into each end of the BASE(1) as shownin FIGURE
¯Attach two 2" SQ, COVERCAPS(28) over each end ofthebase of the REARUPRIGHT(6).
¯SECURELYassemble the PEAKUPP,_IGHT(6) to the BASE(1) as shownin FIGURE1 using two 1/2 X 3-1/4" BOLTS(41.),
1/2" WASHERS(32), and two 1/2" LOCKNUTS(33).
¯SECURELYassemble the P,_IGHT(4) and LEFTHANDLES(5) to the BASE(1) on their respective sides using four 3/8
BOLTS(37), eight 3/8" WASHERS(29), and four 3/8" LOCKNUTS(31).
¯ Slide two 1 X5" GRIPS(23) over the ends of the RIGHT(4) and LEFTHANDLES(5) as shownin FIGURE
6

~1/2 X 5"
_LLL
_LLLL
LLLLLLLLLLLLLL
_LLLLLLLLLLLLLLLLL
.LLLLLLLLLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
.LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL[
LLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
_LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL[
_LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLLL
LLLLLLLLLLLLLLLL
_LLLLLLLLL
L
FIGURE 2
STEP2:
¯Insert four 1/2" FLANGEBEARINGS(46) into the BUSHINGSon the BASE(1), and four 1/2" FLANGEBEARINGS(46)
the BUSHINGSon the PLATFORM(11) as shown in FIGURE
¯ Assemblethe PLATFORM(11) between the BUSHINGSon the BASE(1) as shownin FIGURE2 using two 1/2 X 5" BOLT’3
" T
andtwo 1/2 LOCKNUS (33). (TIGHTEN THE CONNECTIONENOUGHTO REMOVETHE PLAY, YET ALLOWING
THE PLATFORMTO ROTATE FREELY)
STEP3:
¯Attach four 1-1/2 X3/4" PARAGLIDESTRIPS(27) to the end
the PLATFORMADJUSTMENT(12), and four 1-1/2 X 3/4"
PARAGLIDESTRIPS(27) to the end of the PLATFORMSLEEVE
as shownin FIGURE3 using the following steps:
¯ Thoroughlyclean all surfaces where the PARAGLIDE
STRIPS(27) are to be attached.
¯Removethe PARAGLIDESTRIPS(27) from the paper
backingand firmly apply themto all shownsurfaces.
SECURELYAssemble one 1/2" DIA. SPRINGPIN (47) to the
SPRINGPIN HOUSING,on the PLATFORMSLEEVE(2)
showninFIGURE 3. (!!! IMPORTANT!!! TIGHTENTHE
NUT OF THE SPRING PIN SECURELY)
FIGURE 3

_LLLL
_LLLL
.LLLLI
1/2 X 4"~
FIGURE4
STEP 4:
¯ Assemblethe PLATFORMSLEEVE(2) to the BASE(1) as shownin FIGURE4 using one 1/2 X4" BOLT(42), and one
LOCKNUT(33). (TIGHTENTHECONNECTIONENOUGHTO REMOVETHE PLAY, YET ALLOWINGTHEPLAT-
FORMSLEEVETO ROTATEFREELY)
¯ Pull back the 1/2" DIA.SPRINGPIN(47) on the PLATFORMSLEEVE(2) and insert the PLATFORMADJUSTMENT(12)
it. Slide the PLATFORMADJUSTMENT(12) downto the first adjustmenthole andrelease the SPRINGPIN(47).
Assemblethe PLATFORMADJUSTMENT(12) to the PLATFORM(11) as shownin FIGURE4 using one 1/2 X 4" BOLT(42),
and one 1/2" LOCKNUT(33). (TIGHTENTHECONNECTIONENOUGHTO REMOVETHEPLAY, YET ALLOWING
THE PLATFORMADJUSTMENTTO ROTATEFREELY)
1/2 [ 1/2 I 1/2 [ 1/2 I1/2 I 1/2
5 6
1[ I I
I I I 6

’@1/2 X 4-1/2"
)
I
I
I
I
I
I
I
I
/
I
I
!
!
/
/
/
/
FIGURE 5
3/8 X 4-1/2"@
~
STEP5:
¯LOOSELYassemble the LEFT(8) and RIGHTRAILS(9), along with the SEATPAD(18) to the BASE(1) as shownin
using two 3/8 X 4-1/2" BOLTS(38), two 3/8" LOCKWASteRS(30), and two 3/8" WASHERS(29). Temporarilyasselnble
RAILSto the REARUPRIGHT(6) using two1/2 X4-1/2" BOLTS(43) to aid in the assemblyof this step.
7

1/2 X 4-1/2 ~
FIGURE 6
STEP 6:
¯ Insert four 2" SQ. ENDCAPS(26) into the each end of the CARRIAGE(16) as shownin FIGURE
¯SECURELYassemble four 3" DIA. WHEELS(20) to the sides of the CARRIAGE(16) as shown in FIGURE6 using
4-1/2" BOLTS(43), eight 1/2" WASHERS(32), and four 1/2" LOWHEIGHTLOCKNUTS(34).
¯ Attach one 4 X14" NONSKIDSTRIP(25) to the CARRIAGE(16) as shown in FIGURE
I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 6

LOW HEIGHT
1/2 X 2-3/4"~
[GURE 7
~3/8 X 2"
STEP7:
¯SECURELYassemble two 2" DIA. WHEELS(21) to the BRACKETSonthe left side of the CARRIAGE(16) as shown
FIGURE7 using two 3/8 X 2" BOLTS(36), four 3/8" WASHERS(29), and two 3/8" LOCKNUTS(31).
¯Assemblethe two ADJ. WHEELBRACKETS(14) to the right side of the CARRIAGE(16) as shownin FIGURE7 using two
X 2-3/4" BOLTS(40), two 1/2" WASHERS(32), and two 1/2" LOWI-I~, IGHTLOCKNUTS(34). (NOTE:TIGHTENBIIACK-
ETS SECURELYTO THE CARRIAGE, THENBACKNUTOFF 1/2 TURNTO ALLOWFORADJUSTMENTIN A
LATTERS TEP).
¯SECURELYassemble two 2" DIA. WHEELS(21) to the ADJ. WHEELBRACKETS(14) on the right side of the CARRIAGE
(16) as shownin FIGURE7 using two 3/8 X2" BOLTS(36), four 3/8" WASHERS(29), and two 3/8" LOCKNUTS
9

Q1/2X4-1/2"
SAFTEY
STOP
FIGURE 8
STEP8:
¯ Removethe twotemporary.1/2 X4-1/2" BOLTS(43) fromSTEP
¯ Swingthe LEFT(8) andRIGHT(9) RAILSout enoughto insert the CARRIAGEASSEIV~LY(16) in between
CARRIAGE(16) to rest on the SAFETYSTOPSunderneaththe RAILS.See FIGURE
1/2 ] 1/2 I 1/2 [ 1/2 ]1/2 I1/2 I
6
2II I
1I I I I10
Allowthe