PEERLESS PSM-UNV Guide

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
Installation and Assembly:
Models: PSM-UNV, PSM-UNV-S, PSM-UNV-W
Tray Style Projector Mount
This product is UL Listed. It must be
installed by a qualified professional
installer.
R
Maximum UL Load Capacity:
50 lb (22.7 kg)

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•drill with 1/4", 3/8", and 5/32" drill bits
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
• Never exceed the Maximum UL Load Capacity. See page 1.
• If mounting to wood ceiling joists, make sure that mounting screws are anchored into the center of the joists. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
WARNING
Accessories
•Lightweight Adjustable Suspended Ceiling Kit (CMJ 500)
•Lightweight Suspended Ceiling Kit (CMJ 455)
•Accessory Pack for CMJ 455 (ACC 455)*
•Lightweight Cathedral Ceiling Plate (ACC 912)*
•Unistrut or Structural Ceiling Plates (CMJ 300, CMJ 310)*
•Anti-Vibration Ceiling Plates (ACC 845)*
•I-Beam Clamps (ACC 558, ACC 559)
•Truss Ceiling Adapter (ACC 557)*
•Unistrut Adapter (ACC 550)
•Escutcheon Ring (ACC 640)*
•Round Ceiling Plate (ACC 570)
•Cord Wrap (ACC 852, ACC 852W, ACC 852S)*
•3/4" Pipe Reducer (ACC 913)*
•Fixed Length 1 1/2" Extension Columns
(EXT models)
•Adjustable Length 1 1/2" Extension Columns
(ADJ models)
•Extension Column Stabilizer Kit (ACC 050)*
•Extension Column Connector (ACC 109)
•1/2" Threaded Rod (ACC 820)*
•Threaded Rod Adapter (ACC 810)*
Installations:
To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings ........................................................................................ page 4
To Concrete Ceilings .................................................................................................................................... page 5
To Extension Column ................................................................................................................................... page 6
Projector Alignment:
Adjusting Roll Pitch and Yaw ........................................................................................................ step 8, page 9
IMPORTANT! Turn to the appropriate page for your ceiling installation.
*Not UL Listed

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
F
B
Note: Actual parts may appear slightly different than illustrated.
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
Before you start check the parts list below to make sure all of the parts shown are included.
Parts List
H
JKMOP
DEG
QR
A
N
W
CI
L
U
VXY
Description Qty. PSM-UNV PSM-UNV-S PSM-UNV-W
Atray assembly 1 055-0724 055-0724-S 055-0724-W
Bcord management adapter 1 580-1025 580-4025 580-2025
Cspacer 12 540-9416 540-9416 540-9416
Dbushing 4 590-1116 590-1116 590-1116
Esquare nut 4 530-1022 530-1022 530-1022
Fwasher 4 540-1025 540-1025 540-1025
G1/4 x 3/8 socket pin screw 4 520-1109 520-1109 520-1109
HM3 x 16mm serrated washer head socket pin screw 4 510-1083 510-1083 510-1083
IM3 x 25mm serrated washer head socket pin screw 4 510-1127 510-1127 510-1127
JM4 x 16mm serrated washer head socket pin screw 4 510-1087 510-1087 510-1087
KM4 x 25mm serrated washer head socket pin screw 4 510-1082 510-1082 510-1082
LM4 x 35mm serrated washer head socket pin screw 4 510-1097 510-1097 510-1097
MM5 x 16mm serrated washer head socket pin screw 4 510-1161 510-1161 510-1161
NM5 x 25mm serrated washer head socket pin screw 4 510-1122 510-1122 510-1122
OM6 x 20mm serrated washer head socket pin screw 4 510-9554 510-9554 510-9554
PM6 x 30mm serrated washer head socket pin screw 4 510-1067 510-1067 510-1067
Q2 mm allen wrench 1 560-1097 560-1097 560-1097
R4 mm allen wrench 1 560-9646 560-9646 560-9646
Slock plug 1 3022-502 3022-502 3022-502
Tthumb screw 1 560-0106 560-0106 560-0106
Uwood screw 2 5S1-015-C03 5S1-015-C04 5S1-015-C04
Valligator anchor 2 590-0097 590-0097 590-0097
WM5 x 10mm socket pin screw 1 520-1164 520-2031 520-2031
X10-32 x 3/16 slotted set screw 1 520-1187 520-2187 520-2187
Yceiling plate 1 580-1042 580-4042 580-4042
Zkey 1 0000-322 0000-322 0000-322
ST
Note: Assembled to
tray assembly (B)
Z

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
U
U
Y
WOOD
JOIST
CEILING
Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (Y) with two #14 x 2.5"
(6 mm x 65 mm) wood screws (U) as shown using 3/8" (10 mm) socket wrench.
Skip to step 2
Installation To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
• Tighten wood screws so that ceiling plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
WARNING
• It is the responsibility of the installer to verify that the
supporting surface will safely support the combined
load of all attached hardware and components.
WARNING
1

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
Drill two 1/4" (6 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach ceiling plate (Y)
using two concrete anchors (V) and #14 x 2.5"
wood screws (U) as shown in Illustration A and
1, 2, and 3 (below). Tighten all fasteners.
Skip to step 2
1
3
CUTAWAY VIEW
INCORRECT
concrete
metal
bracket
plaster/
dry wall
CORRECT
concrete
metal
bracket
plaster/
dry wall
concrete
ceiling
concrete
anchor
concrete
anchor
concrete
anchor
U
U
2Y
Drill hole and insert anchor
Place ceiling plate over anchor and secure with screw
After repeating step one tighten all fasteners
• When installing Peerless wall mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete
surface in the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must
meet ASTM C-90 specifications.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity.
WARNING
• Always attach concrete expansion anchors directly to
load-bearing concrete.
• Never attach concrete expansion anchors to concrete
covered with plaster, drywall, or other finishing mate-
rial. If mounting to concrete surfaces covered with a
finishing surface is unavoidable, the finishing surface
must be counterbored as shown below. If plaster/
drywall is thicker than 5/8", custom fasteners must be
supplied by installer (not UL approved).
WARNING
Illustration A
U
Y
CONCRETE CEILING
V
1
Installation to Concrete Ceilings
• Tighten wood screws so that ceiling plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
6 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
1
2
Installation to Extension Column
Thread tray assembly (A) into cord management (B) to extension column (sold separately) as shown.
Note: Slotted set screw (X) is used to jam against threads of extension column to prevent any excess movement
of projector mount assembly (A).
Skip to step 2
A
B
• Do not overtighten! Overtightening may cause
permanent damage to the projector. Torque to
26-35 in • lb (30-40 kg • cm).
WARNING
Remove the lock plug (S) by using key to unscrew it from the assembly as shown in detail 2.1. Open the
mount and remove thumb screw as shown in detail 2.2.
Note: The upper tray of the mount will now slide off of the lower tray.
DETAIL 2.1 DETAIL 2.2
STHUMB
SCREW
1 1/2" EXTENSION
COLUMN
(SOLD SEPARATELY)
UL LISTED EXT OR
ADJ SERIES)

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
7 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
Flip projector upside down. Attach lower tray to
the bottom of the projector using appropriate
number of screws (H,I,J,K,L,M,N,O,P),
washers (F) and spacers (C) as shown. Use
4 mm allen wrench (R) to tighten
screws (H,I,J,K,L,M,N,O,P).
Important: If projector does not have at least
three mounting holes, do not use this adapter
plate.
Note: Some projectors have feet which can be
removed and the corresponding threaded insert
can be used for a mounting hole.
Note: Projector may differ slightly in appearance.
Installation of Projector
PROJECTOR
LOWER
TRAY
4
F
C
4Thread tilting mechanism of top tray into ceiling plate (Y). Align the notch with one of the four holes of the ceiling
plate (Y) and secure tilting mechanism with a M5 x 10 mm socket pin screw (W) using 4mm security
allen wrench (R) as shown in detail 3.
Note: Slotted set screw (X) is used to jam against the threads of the tilting
mechanism to prevent any excess movement of the upper tray. Do not
overtighten screw; overtightening screw will damage threads making it
difficult to separate the products.
DETAIL 3
Y
WOOD
JOIST
CEILING
Attaching Top Tray
X
W
UPPER
TRAY TILTING
MECHANISM
IMPORTANT! Be sure not to touch the
projector while tightening the set screw on
the tilting mechanism. This may cause the
image to be unaligned when you let go.
3
Y
TILTING
MECHANISM
NOTCH
SCREW
• Do not overtighten! Overtightening may cause
permanent damage to the projector. Torque to
26-35 in • lb (30-40 kg • cm).
WARNING

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
8 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
Slide upper tray into the lower tray as shown.
• Do not lift more weight than you can handle! Use
additional man power or mechanical lifting equipment
to safely handle placement of the projector!
WARNING
UPPER
TRAY
LOWER
TRAY
Attach thumb screw to mount as shown to lock
the upper tray to the lower tray.
UPPER
TRAY
THUMB
SCREW
LOWER
TRAY
5
6

ISSUED: 08-09-06 SHEET #: 055-9469-2 04-11-08
Visit the Peerless Web Site at www.peerlessmounts.com
9 of 9
For customer care call 1-800-729-0307 or 708-865-8870.
Close the mount and insert the lock plug (S) and key (Z) as shown.
Note: To remove key, slot must be in the horizontal position. This may require that you back off 1/4 turn.
IMPORTANT: Key is neccesary for projector removal. Store it in a safe place.
To adjust roll, pitch, and yaw loosen the set screw (shown below) using security allen wrench (R)or standard 4
mm allen wrench. You should be able to just slightly loosen the screw so that your adjustments can be set without
having to hold the projector. Move projector to desired position and slowly tighten set screw.
Note: Be sure not to touch the projector while tightening the set screw. This may cause the image to be
unaligned when you let go.
IMPORTANT: Allen wrench (R) is your key for projector removal. Store it in a safe place.
SET SCREW
7
8
S
Z
© 2008, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.