Phanteks ECLIPSE G300A User manual

up to 360 up to 240
INSTALLATION GUIDE
INSTRUCTIONS
Thank you for choosing Phanteks. Please take a moment to
carefully go through the manual. This manual will walk you
through all of the features the Eclipse G300A has to offer and
installation steps to build a full system.
Phanteks will not take responsibility for any damages incurred due to incorrect
installation or usage of this product.
VERSION 1.0
| www.phanteks.com 01
USB 3.0 TYPE-A
USB 3.0 TYPE-C
AUDIO/MIC
RESET BUTTON
POWER BUTTON
SSD + MOTHERBOARD
SCREW
18x
MB STAND-OFF
1x
PSU SCREW
4x
HDD SCREW
4x
STAND-OFF TOOL
1x
D-RGB 120MM FAN
1x pre-installed DBK01
3x pre-installed DBK02
ZIP TIE
6x
360 FRONT AIO COOLER 240 TOP AIO COOLER
FRONT TOP REAR CLEARANCE FANS
RADIATOR
120mm
120mm
3x 2x 1x
up to 120
-
-
-
-
-
-
140mm
140mm
CPU cooler height
GPU length
Powersupply
E-ATX
160 mm
365 mm with front fans
210 mm
up to 260 mm width
AIO 240
AIO 360
Because of the special front bracket, the front supports a radiator
up to 360. When using this option, the maximum GPU length is
335mm.
The top supports a radiator up to 240. When using this option,
the maximum GPU length is 365mm with 3 front 120mm fans.
120MM
120MM
120MM
120MM
120MM
120MM
120MM
120MM
120MM
120MM
120MM
120MM
This manual is for the following models:
PH-EC300GA_DBK01
PH-EC300GA_DBK02
Satin Black |1x D-RGB Fan Back
Satin Black |3x D-RGB Fans Front
INCLUDED ACCESSORIES FRONT I/O
FAN & RADIATOR SUPPORT
335mm 365mm
D-RGB MOTHERBOARD ADAPTER
1x

INSTALLATION GUIDE
02
LEFT SIDE PANEL REINSTALL SIDE PANEL
MOTHERBOARD POWERSUPPLY
RIGHT SIDE PANEL FRONT PANEL & DUST FILTERS
Loosen the 2 thumb screws and slide to
remove the tempered glass side panel.
Remove the glass panel, set it aside in a
safe location to prevent damage.
When returning the left side panel, align
the bottom right with the slit in the chassis.
Slide the panel forward and secure with 2
thumb screws at the back.
Remove front panel by pulling the panel from below.
Install the ATX motherboard using 9x motherboard screws.
For M-ATX Motherboards follow the motherboard instructions to
move the stand-offs to the correct position.
Slide in the power supply from the side and secure it with the
4x PSU screws. It is recommended to connect all needed cables
beforehand.
Loosen the 2 captive thumb screws and slide to remove the right
side panel.
| www.phanteks.com
THUMBSCREW
REMOVE
2x
THUMBSCREW
REMOVE
2x
MOTHERBOARD
SCREWS
INSTALL
9x PSU SCREW
INSTALL
4x
REMOVE EXTERNAL PANELS
HARDWARE INSTALLATION
Make sure to hold the side panel while
sliding it outwards to prevent any damage
when removing.
CAUTION
PSU FILTER
TOP FILTER
PSU

INSTALLATION GUIDE 03
STORAGE |2.5” SSD
STORAGE |3.5” HDD
Loosen the thumb screw on the SSD backplate to remove it, for
easy installation of the 2.5” SSD’s.
Hold the 3.5” HDD into place and secure it with 4x HDD screws
from the bottom.
Lay the chassis on it’s side for easy access.
The backplate can hold up to 3x 2.5” SSD’s. Use 4x SSD screws
per SSD to secure it in location.
| www.phanteks.com
Connect the front I/O cables to the allocated connectors on the
motherboard to use all front I/O buttons and inputs.
MOTHERBOARD FRONT I/O
SSD SCREW
INSTALL
4x
HDD SCREW
INSTALL
4x
INSTALLATION GUIDE
VERSION 1.0
2.5”
SSD
2.5”
SSD
2.5”
SSD
FRONT I/O
THUMBSCREW
LOOSEN
1x
POWER_SW
4x
Put a piece of cloth underneath
the chassis to prevent any
damage.
PRO TIP
POWER
SWITCH
PWR
LED
RESET
SWITCH

INSTALLATION GUIDE
04 | www.phanteks.com
VERTICAL GPU BRACKET (PH-VGPUKT4.0_03R)
The G300A chassis supports the Phanteks Vertical GPU Bracket.
The Vertical GPU Bracket supports 3 and 4 slot GPU’s with access
to the GPU connectors on slot 1 and 2.
It can be easily installed in the PCI slot area. Follow the instructions
that are included with the Vertical GPU bracket.
OPTIONAL UPGRADE
The D-RGB fan needs a controller to function.
Connect to an ARGB-equipped motherboard with the included
D-RGB Motherboard adapter or use a Phanteks D-RGB Controller.
The Phanteks D-RGB Controller is sold separately (PH-CTHUB_DRGB_01).
More Phanteks D-RGB lighting products can be
daisy-chained easily with the JST-connector.
OPTION 1.
MOTHERBOARD CONTROL
OPTION 2.
PHANTEKS D-RGB CONTROLLER
CONNECT TO THE D-RGB CONTROLLER WITH
JST CONNECTOR.
DAISY-CHAIN PHANTEKS D-RGB PRODUCTS TOGETHER
WITH THE JST-CONNECTOR.
PHANTEKS DRGB CONTROLLER SOLD SEPARATELY
(PH-CTHUB_DRGB_01)
EXPAND WITH MORE D-RGB PRODUCTS
D-RGB FAN
D-RGB FAN MOTHERBOARD
D-RGB CONTROLLER
D-RGB CABLES
As a Phanteks customer, you are priority number one. We have a dedicated team across the globe to deliver the experience you
deserve.
CUSTOMER CARE
RMA and Technical Support Americas
Hours: Monday-Friday 9:00-5:00 PST
Phone number: [phone]
Email: [email protected]
Facebook: @Phanteks
RMA and Technical Support International
Email: [email protected]
Facebook: @Phanteks
For spare parts and optional upgrades please visit:
www.axpertec.com (EU) | www.phanteksusa.com (US)
SUPPORT & WARRANTY
D-RGB CONTROL D-RGB EXPANSION