Pima FORCE Series User manual

FORCE Series
Advanced Intruder Alarm Systems
Installation Guide
System Version: 1.3.x

FORCE Series Installation Guide
2PIMA Electronic Systems
Table of Contents
1Introduction........................................................................................ 5
1.1 Main features.............................................................................................. 5
1.2 System comparison table.............................................................................. 6
1.3 Technical specifications ................................................................................ 7
1.4 Ordering information.................................................................................... 7
1.4.1 Peripherals ............................................................................................ 7
2The Control Panel................................................................................ 9
2.1 Location guidelines ...................................................................................... 9
2.2 Installation ................................................................................................. 9
2.3 The control panel’s circuit board ...................................................................10
2.3.1 The bus ...............................................................................................11
2.3.2 Zone wiring ..........................................................................................11
2.3.3 Zone doubling.......................................................................................12
2.4 Tamper switches ........................................................................................12
2.5 Wired sirens ..............................................................................................12
2.6 Alarm and On/Off outputs ............................................................................12
2.7 Relay........................................................................................................13
2.8 Wired keypads ...........................................................................................13
2.8.1 Keypad ID number ................................................................................13
2.9 Phone line and set ......................................................................................13
3System Programming........................................................................ 14
3.1 Menus and codes........................................................................................14
3.1.1 Code setting guidelines ..........................................................................14
3.1.2 Activation codes ....................................................................................14
3.2 Changing the default Master and Technician codes ..........................................14
3.3 The technician menu ...................................................................................15
3.3.1 System Configuration.............................................................................15
3.3.2 Tests & Diagnostics................................................................................15
4Peripherals........................................................................................ 16
4.1 Zone expanders .........................................................................................16
4.2 Tampers and EOLs......................................................................................16
4.3 Keypad Settings .........................................................................................17
4.4 Wireless peripherals....................................................................................17
5Zones ................................................................................................ 20
5.1 Zone Settings ............................................................................................20
5.2 Zone Types Settings ...................................................................................21
5.2.1 Attributes.............................................................................................21
5.3 Copy Zones ...............................................................................................22
5.3.1 Single to Multiple...................................................................................22
5.3.2 Multiple to Multiple ................................................................................22
5.4 Partitions Names ........................................................................................22
6Outputs ............................................................................................. 23
6.1 Onboard.................................................................................................... 23
6.1.1 The Ext./Int. siren outputs......................................................................24
6.2 Zone Expanders .........................................................................................24
6.3 Outputs Expander.......................................................................................24
6.4 Wireless Sirens ..........................................................................................24
7CMS & Communications .................................................................... 25
7.1 Monitoring Stations.....................................................................................25
7.1.1 CMS 1-2...............................................................................................25
7.1.2 Radio...................................................................................................27
7.1.3 Custom Zones Reports ...........................................................................28
7.2 PIMA Cloud................................................................................................28

Table of Contents
PIMA Electronic Systems 3
7.3 General Settings.........................................................................................29
7.4 Telephone Settings .....................................................................................29
7.5 Network Settings........................................................................................29
7.6 Cellular Settings .........................................................................................30
8Faults................................................................................................ 31
8.1 AC Fault ....................................................................................................31
8.2 Low Battery, Phone Line, Network, Cellular Module ..........................................31
8.3 Invalid Code ..............................................................................................31
8.4 CMS Comm., Tamper Open, Invalid Code, Other Faults ...................................31
9Timers and Counters ......................................................................... 32
9.1 Programmable Output Types ........................................................................33
10 General Settings ............................................................................... 34
10.1 Arming Prevention ......................................................................................35
11 Reset to Defaults .............................................................................. 36
11.1 Resetting to factory defaults.........................................................................36
12 Tests & Diagnostics........................................................................... 37
12.1 Event Memory............................................................................................37
12.2 Zone Test..................................................................................................37
12.3 Output Test ...............................................................................................38
12.4 Power Diagnostics.......................................................................................38
12.5 Communication Tests ..................................................................................38
12.6 Communication Monitor...............................................................................38
12.7 Wireless Peripherals....................................................................................38
Appendixes
Appendix A. Implementing Partitions.................................................... 39
Appendix B. Remote Up/Download ....................................................... 40
Appendix C. Programmable Output Types ............................................. 41
Appendix D. Technician and CMS Codes................................................. 42
Appendix E. Text and Characters .......................................................... 43
Appendix F. Zone and System Status .................................................... 44
Appendix G. CMS Event Reporting ......................................................... 45
Appendix H. Glossary ............................................................................ 46
Table of Figures
Figure 1. The control panel’s rack.................................................................. 10
Figure 2. The rack’s lid ................................................................................ 10
Figure 3. The control panel’s circuit board diagram.......................................... 10
Figure 4. No EOL......................................................................................... 11
Figure 5. One EOL....................................................................................... 11
Figure 6. Two EOLs ..................................................................................... 11
Figure 7. Sirens connection diagram.............................................................. 12
Figure 8. Line and Set connections ................................................................ 13
Figure 9. Event memory log ......................................................................... 37

FORCE Series Installation Guide
4PIMA Electronic Systems
Safety Instructions. Read Carefully
The FORCE security system has been registered in accordance with EN60950 and its rules.
Among other things, EN60950 requires us to advise you the following information:
Hazards of fire and electric shock exist in this alarm system. To reduce the risk of fire or
electric shock, do not expose this alarm system to rain or moisture. Pay attention: Telephone
cords could be a good conductor for lightings energy.
Warning: this equipment has no mains On/Off switch. The plug of the direct plug-in power
supply is intended to serve as the disconnecting device.
Dangerous high voltages are present inside the control panel’s enclosure. Refer servicing to
qualified personnel only.
This alarm system should be used with 230VAC/110VAC, 50/60Hz, protected by anti-electric
shock breaker. Use only the power supply provided with this equipment. Use of unauthorized
power supplies may cause damage.
Do not spill liquid of any kind onto the unit. If liquid is accidentally spilled onto the unit,
immediately consult a qualified service.
Disposal of used batteries must be made in accordance with local waste recovery and
recycling regulations.
Default Codes
Master: 5555
Installer: 1234
Signs in this guide
Warning
Note
Enter sub-menus, select/deselect, save selection

Menu with sub-menus

Options menu
Return/Back, cancel (except in the Keypad Settings menu)
/
Select/deselect to enable/disable
#/*
Scroll between zones, partitions, users, etc.

1: Introduction
5PIMA Electronic Systems
1Introduction
This guide will introduce you with the new hybrid, highly reliable FORCE Series (hereinafter,
FORCE) intruder alarm systems, that includes the FORCE, the FORCE Lite and the FORCE 32.
With 7-line, LCD screen, clear menu-driven display keypads, the FORCE is an intuitive, easy to
install and use alarm system.
FORCE offers advanced communication and expanding technology, including wireless receivers
and peripherals.
The Technician and User subject menus make programming and navigating the menu fast and
easy. Help screens improves servicing.
A special Tests & Diagnostics menu allows you to view various information about the current
system status, and test it and the its peripherals.
The PIMAlink 3.0 cloud service and smartphone application allow the end-user to control the
FORCE system from anywhere.
This Installation guide refers to the FORCE alarm system, version 1.3.x. All systems are supplied
with two guides:
This guide that includes the control panel’s installation and wiring instructions, as well as
the technician-programming guide.
The User guide that includes the user-programming guide and the system maintenance
instructions.
1.1 Main features
FORCE
Zones: eight onboard, expandable to 144 (including double zoning), including up to
64 wireless
1
.
Users: up to 144, with a unique code for each, up to 64 of which with a remote control.
Contacts: up to 32, for receiving alarm and other notifications.
Partitions: up to 16, with a separate keypad for each.
Expanders for 8 and 16 zones, with one or two relays on each
Multi-channel communications: Ethernet, 3G, Cellular Data, PSTN and Radio.
Up to two CMSs (Central Monitoring Station) with password protection for each
Remote operations via PIMAlink 3.0 cloud and smartphone application
Graphic, LCD, 7-line keypad display with various menus.
Detailed test and diagnostics menu
Remote and local upload/download via the Force Manager software, via all media.
Remote firmware update via the Force Manager software
1
Requires a wireless receiver

FORCE Series Installation Guide
6PIMA Electronic Systems
FORCE Lite
Zones: eight onboard, expandable to 32, and 24 wireless
2
(a total of 64, including double
zoning).
Users: up to 64, with a unique code for each, up to 24 of which with a remote control.
Contacts: up to 16, for receiving alarm and other notifications.
Up to eight true partitions, with separate keypads (up to eight) for each.
Multi-channel communications: Ethernet, 2G/3G/4G, Cellular Data, and Radio.
One siren output
One tamper input
FORCE 32
Zones: eight onboard, expandable to 32 (including double zoning), including 24 wireless
3
.
Users: up to 32, with a unique code for each, up to 24 of which with a remote control.
Contacts: up to 16, for receiving alarm and other notifications.
Up to four true partitions/8 keypads
Multi-path communications: cellular (2-4G), PSTN, radio, and network (limited). The
network connection only allows connecting with the FORCE Manager up/download software.
One siren output
One tamper input
FORCE 32C
The FORCE 32Chas the same features as the FORCE 32, except that it has full network capacity
as in the FORCE.
1.2 System comparison table
Feature
FORCE
FORCE Lite
FORCE 32/32C
Hardwired zones
8-144
8-64
8-32
Wireless zones (max.)
64
24
24
Users
144
64
32
Contacts
32
16
16
Partitions
16
8
4
Onboard network
connection


4
Communication paths
Network, PSTN,
cellular, radio
Network,
cellular, radio
PSTN, cellular, radio,
network (limited4)
Output current
1.1A
750mA
750mA
Siren outputs
2
1
1
Relay output
1
-
1
2
Requires a wireless receiver
3
Requires a wireless receiver
4
See the limited network connection features for each system above the table.

1: Introduction
PIMA Electronic Systems 7
1.3 Technical specifications
AC power input: 11-18V. FORCE Lite: 14.5V
Backup battery input: 13.8VDC
Relay: 1A max.
On/Off and Alarm outputs (minus, open drain): 10A max., external power: +25V max.
Output current
Max: +13.8VDC, 1.1A. FORCE Lite/32:+13.8VDC, 750mA
Idle: 50mA
EOL resistors: programmable
Operating temperature: -10 to +50 °C
Humidity (max.): 93% R.H., non-condensing
1.4 Ordering information
Product
P/N
FORCE
8350012
FORCE Lite
8350056
FORCE 32
8350212
FORCE 32C
8350303
1.4.1 Peripherals
Product
Description
P/N
Hardwired
KLA500
Keypad arming station (wired)
8415020
KLR500
Rubber key, LCD screen keypad
8415001
KLT500
Touch key, LCD screen keypad
8415010
ZEL508
Local 8-zone expander. The card is installed beside the
control panel and is connected using a special 4-wire cable.
8330011
ZEX508
8-zone expander with one relay output
8500026
ZEP608
8-zone expander with PS-2 1.2A power supply, mounted in a
metal case.
8290011
ZEX516
16-zone expander with two relay outputs
8500027
ZEP716
16-zone expander with 13.8V to 4.2A power supply,
mounted in a metal case.
8290013
OEX508
8-relay outputs expander
8500028
Radio and cellular
TRV-100
TRU-100
Long-range radio transmitters
TRV-100 Low: 8200011
TRV-100 High: 8200010
TRU-100 Low: 8300005
TRU-100 Medium: 8300009
TRU-100 High: 8300006
VHF Antenna 42cm: 6110003
VHF Antenna 51cm: 6110007
UHF Antenna: 6110004
CLM302
Cellular add-on (2G/3G)
8300045
CLM412
Cellular add-on (4G)
8300049
GSM501
Cellular add-on (2G)
8300040
GSM512
Cellular add-on (3G)
8300043
Wireless5
5
Frecuencias: 143: 433.92Mhz, 187:868.95Mhz

FORCE Series Installation Guide
8PIMA Electronic Systems
Product
Description
P/N
DPS
PIR motion detector
143: 8831010
187: 8831024
DPP
PIR motion detector with pet immunity
143: 8831012
187: 8831025
DPC
PIR motion curtain detector
143: 8831014
187: 8831026
DGS
Gas detector
143: 8832004
187: 8832009
DSC
Smoke CO detector
143: 8832006
DFL
Flood detector
143: 8831006
187: 8831029
DCM
Door contact
143: 8831002
187: 8831028
RPB
Panic button
Black:
o143: 8833010
White:
o143: 8833006
o187: 8833011
KAS
Arming Station
143: 8833002
187: 8833014
SRO
Siren
143: 8831016
187: 8831023
WRF
64-zone receiver (PIMA peripherals).
FORCE Lite: 24 zones
143: 8500030
187: 8500041
WRB
64-zone receiver (Visonic peripherals). FORCE Lite: 24
zones
143: 8500038
187: 8500039
WRP
Repeater
143: 8831020
187: 8831030

2: The Control Panel
PIMA Electronic Systems 9
2The Control Panel
2.1 Location guidelines
To make installation and servicing easy and efficient, the FORCE’s control panel, transformer
and backup battery are mounted on a special rack. The rack is covered by a metal lid.
Use the following list as a guide to find a suitable location to install the FORCE security system:
Install the control panel in a protected location, where people cannot trip over any
line or power cord.
Select a location free from vibration and shock.
Mount this product on a flat stable surface, near telephone and network sockets, and
a power outlet.
Do not choose a location that exposes the control panel to direct sunlight, excessive
heat, moisture, vapors, chemicals, or dust.
Protect cords from damage or abrasion.
Disconnect all sources of power supply prior to installation. Pay attention: do not
install low voltage wires near any AC power wires. They should be installed
separately.
Do not install this product near water, e.g. bath tub, sink, wet basement.
2.2 Installation
Make sure AC power and battery are not connected prior to
installation.
The control panel is installed on a designated metal rack. The rack is supplied with a lid. The
rack is also designed to hold a transformer, a backup battery, a local zone expander (optional),
and a radio transmitter.
To install the control panel, follow the next steps.
1. Use the next diagram to position the two upper and one middle hanging holes.
2. Pass the wires of the zones and expanders from behind the rack, through the opening.
3. According to the designated surface, use appropriate wall plugs (if necessary) and screws
and mount the rack.
4. Connect the wiring.
5. Place the metal cover: tilt it upwards, insert the 2 tooth on the rack to the notches on the
cover, place the cover on the rack and fasten the screw at the bottom.

FORCE Series Installation Guide
10 PIMA Electronic Systems
Figure 1. The control panel’s rack
Figure 2. The rack’s lid
2.3 The control panel’s circuit board
Figure 3. The control panel’s circuit board diagram
Following is a table of the circuit board’s terminals.
No.
Label
Description
1
ZONES
Z1-Z8 zones, (+)/(-) detectors’ voltage
2
TMPR1-2
Tamper switches 1-2; FORCE Lite/32: TMPR 2 input unavailable.
3
SIRENS Ext./Int.
External/internal sirens, (+)/(-); FORCE Lite/32: the Int. output is
unavailable.
4
ALRM
Output (by default, switched to minus at alarm)
5
ON/OFF
Output: (by default, switched to minus on arming)
6
(-)
GND (-)
7
RELAY
Output: NC (Normally Close), C (Common), NO (Normally Open);
FORCE Lite: unavailable
8
FORCE BUS
The -/+/In/Out terminals are numbered 1-4. All expanders and
keypads have the same wire numbering.
1 2 3 4 5 7 8
11
12
13
14
151617
18
19
6 9
10

2: The Control Panel
PIMA Electronic Systems 11
No.
Label
Description
9
ETHERNET
Ethernet socket. FORCE 32: available only for connecting to the
FORCE Manager software.
10
-
Technician keypad’s and local zone expander ZEL508 connector
11
Earth ground; use only with non-PIMA non-metal cases!
12
LINE
Telephone line; FORCE Lite: unavailable
13
SET
Telephone set, fax, answering machine; FORCE Lite: unavailable
14
-
Cellular add-on socket
15
EXPANSION
For future use
16
SERIAL
RS-232 socket
17
TRANSMITTER
Radio transmitter socket
18
AC
VAC input
19
BATT
Backup battery, Red (+)/Black (-) cables
The Int. Siren, Relay, and Line/Set terminals are not assembled in the
FORCE Lite PCB, and the transformer’s voltage is 14.5VAC.
2.3.1 The bus
The bus is a serial communication channel, used for exchanging data between the control panel
and the peripherals. The protocol in use by the bus is ForceCom (PIMA proprietary).
Use four 0.5mm (24 Gauge (AWG)) wires for the bus. The maximum bus length is
500m, including all peripherals and keypads.
Connect the wires using the numbers 1-4, where terminal #1 on the control panel
connects to the same terminal on the peripheral, and so on.
2.3.2 Zone wiring
Figure 4. No EOL6
Figure 5. One EOL
Figure 6. Two EOLs
6
End Of Line resistor

FORCE Series Installation Guide
12 PIMA Electronic Systems
2.3.3 Zone doubling
Zone Doubling allows you to double the eight onboard zones to 16. All doubled zones must be
wired according to the diagram below.
In the diagram on the right (all values are for example only), the zone
using the 10KΩresistor will be the first zone (lower number zone) and
the zone using the 5.1KΩresistor will be the second zone (higher
number zone).
For example, Zone #1 input will serve Zone #1 (10KΩ) and Zone #9
(5.1KΩ), Zone #2 input will serve Zone #2 and zone #10, and so on.
2.4 Tamper switches
TMPR 1 & 2 are inputs for tamper switches in boxes, detectors, sirens, etc.
By default, the control panel’s box tamper is connected to TMPR 1 input.
To connect tampers, follow the next steps:
1. Connect one wire to the TMPR 1 or 2 terminals.
FORCE Lite/32: TMPR2 terminal is not available.
2. Connect the other wire to a (-) input.
3. Set the tampers parameters.
2.5 Wired sirens
Connect any DC siren (only) to the FORCE. To connect sirens, do the steps that follow:
1. Connect an internal siren to the SIRENS Int.
(internal) +/- terminals. FORCE Lite/32: the Int.
terminal is unavailable.
2. Connect an external siren to the SIRENS Ext.
(external) +/- terminals.
3. For EOL loop supervision, connect a 2KΩresistor
between the siren’s wires, close or inside the
siren’s enclosure.
Figure 7. Sirens connection diagram
2.6 Alarm and On/Off outputs
The Alarm and On/Off are open drain outputs.
Connect devices (up to 10A) between the output
and the (+).
The Alarm output supplies ground when the
alarm is triggered (by default).
The On/Off output supplies ground on arming
the alarm system (by default).
Zone 1 (-)
Zone 9
10KW, 5%
5.1KW, 5%
Z1
Control Panel
Control Panel
TMPR 1-2
(-)
Tamper
Switch Sensor
EOL (optional)
External
Siren
Internal
Siren
Device Device

2: The Control Panel
PIMA Electronic Systems 13
2.7 Relay
Connect devices such as electric doors and lights to the relay terminals.
The terminals are NC-Normally Close, C-Common, and NO-
Normally Open.
2.8 Wired keypads
Keypads and other peripherals connect to the bus in the FORCE BUS terminals (see
section 2.3.1). Up to 16 addressable KLT/KLR/KLA keypads with ID=1-16 (or un-addressable
keypads with ID=0) can be used. FORCE Lite/32: up to 8 keypads.
2.8.1 Keypad ID number
To set the keypad ID number:
1. Press and hold the # + ? keys to display the
Keypad ID screen.
2. Enter a number between 1 and 16
3. Press to save and exit.
The keypad’s version is also displayed in this screen.
2.9 Phone line and set
7
1. Connect the phone line cords to the LINE terminals. If
the line is shared with an ADSL modem, use an
appropriate filter.
2. Connect phone set, fax machine or answering machine
to the SET terminals - this will enable the control panel
to answer any incoming call.
Figure 8. Line and Set connections
7
FORCE L ite : not available
Device
Keypad ID:
(0 ... 16)
01
Press to Exit
Version: - xx.xx.xx

FORCE Series Installation Guide
14 PIMA Electronic Systems
3System Programming
3.1 Menus and codes
Like all PIMA alarm systems, FORCE has two menus: User, and Technician, each accessed with
its own Master code. In addition, a new Central Monitoring Station (CMS) menu can have a
separate communication settings lock code.
Master technician code: allows accessing all the technician menus, including all CMSs
menus, as long as no CMS code was set; see next.
CMS lock code: an optional code for locking the CMS definitions from accessing it using the
Master technician code. This code only allows the technician/CMS to set and access the
CMS communication definitions, including the account ID and the communication paths.
3.1.1 Code setting guidelines
Note the following when setting codes in the FORCE security system:
All codes, except the Quick Arm code are made of four to six digits
The Quick Arm code (set by the users) is made of two digits
A code cannot start with the two digits of the Quick Arm code
Codes 1234 and 5555 are reserved
3.1.2 Activation codes
Eight codes for activating devices (via relay outputs) by the system users - whether it’s an
electric gate or a floodlight, users can turn them on and off using these 8 codes. Triggering the
relay outputs is done using the Activation Codes 1-8 programmed output types (see Appendix C,
on page 41).
Activation codes are subject to keypad and user partitioning (where relevant).
3.2 Changing the default Master and Technician
codes
To enter the menus for the first time, FORCE’s default technician and user Master codes must be
changed. The default Master technician code is 1234 , and the default Master user code is 5555 .
These two codes are reserved.
Follow the next steps to change the default codes.
1. Connect the alarm system to power and wait for the main screen to be displayed.
2. Press 5555 - the codes’ menu is displayed.
3. Press - the curser moves to the right of the Master Code .
4. Enter a new 4-6 digit code. Write down the code and advice the
system owner to keep it in a safe place.
5. Press to save the code.
6. Press the down arrow to the Tech. Code and press .
7. Enter a new 4-6 digit technician code. Write down the code and advice the system owner to
keep it in a safe place.
8. Press to save the code.
9. Press to exit.

3: System Programming
PIMA Electronic Systems 15
3.3 The technician menu
The technician menu is divided into 2 sub-menus: System Configuration, and Tests &
Diagnostics; see below.
3.3.1 System Configuration
The System Configuration menu includes the sub-menus listed in the next table:
Menu
Parameters
Peripherals
Zone and output expanders, keypads, tamper switches, and EOL
resistors.
Zones
Zone and zone type definitions, copy zones.
Outputs
Control panel and expanders’ relay outputs.
CMS & Communications
CMS 1-2 definitions, PIMA cloud, and radio report codes.
Faults
System responses to faults and entering false code.
Timers & Counters
Programmable output types and other timers
General Settings
System name, service provider, Master technician code, and
other parameters.
Reset to Defaults
Partial or full system reset
3.3.2 Tests & Diagnostics
See chapter 12, on page 37.

FORCE Series Installation Guide
16 PIMA Electronic Systems
4Peripherals
The Peripherals menu includes the following sub-menus:
1) Zone Expanders: see below.
2) Tampers and EOLs: see below.
3) Keypads: set the no. of addressable keypads (ID=1-16; FORCE Lite/32: ID=1-8). Keypad
with ID=0 is not supervised, nor can it be partitioned.
4) Keypad Settings: see section 4.3, on page 17.
5) Outputs Expanders: set the no. of the relay output expanders.
6) Wireless Peripherals: see section 4.3, on page 17.
4.1 Zone expanders
System Configuration  Peripherals  Zone Expanders
The Zone Expanders menu includes the following sub-menus:
1) Remote Zone Exp.: set the no. of 8/16 zone expanders.
Each 16-zone expander is programmed as two 8-zone expanders and
occupies 2 consecutive ID numbers. For example, if expander #3 is a
16-zone one, it takes ID numbers 3 and 4 and so expander #4, the next
expander will take ID number 5 (and not 4).
2) Local Zone Expander: select if the ZEL508 local zone expander is installed.
3) Zone Doubling: when selected the onboard zone 1-8 inputs can be used as inputs for 8
additional zones; see section 2.3.3, on page 12.
4.2 Tampers and EOLs
System Configuration  Peripherals  Tampers and EOLs
Parameter
Description
Tamper 1
TMPR1 input is active.
Tamper 1+EOL
TMPR1 input is EOL supervised, for detecting a short (one EOL).
Tamper 2
TMPR2 input is active. FORCE Lite/32: unavailable
Tamper 2+EOL
TMPR2 input is EOL supervised, for detecting a short (one EOL).
External Siren+EOL
The SIREN Ext./Int. output is EOL supervised, for detecting cut and
short.
Internal Siren+EOL
Double EOL
Two EOL resistors are used on all EOL supervised loops.
Resistor 1-2
Enter the resistors values in Ohm. The value entered is multiplied by
100. For example, when using a 2.2kWresistor, set the value to 220 .

4: Peripherals
PIMA Electronic Systems 17
4.3 Keypad Settings
System Configuration  Peripherals  Keypad Settings
Press * or # to select a keypad. Note that the Keypad Settings menu applies only for
addressable keypads with ID=1-16; FORCE Lite/32: ID=1-8.
The Keypads menu includes the following sub-menus:
1) Name: user text, up to 16 characters.
2) Options (press * or # to select a keypad):
Parameter
Description
Illum. During Alarm
The keypad will illuminate during the alarm time.
Illum. During Delay
The keypad will illuminate during the exit/entry delay times.
3) Partitions: select the keypad’s partitions by pressing the desired numbers. The selected
partitions will stay on.
4.4 Wireless peripherals
System Configuration  Peripherals  Wireless Peripherals
1) Global Settings
Parameter
Description
Default
Range
Expanders
Set the no. of wireless receivers. Note that FORCE
automatically allocates wireless zones with numbers higher
than any hardwired zone. If a hardwired zone expander is
installed when wireless zones are already defined, FORCE
will reallocate the wireless zones.
0
0-1
Supervision
Set an interval during which if the control panel receives no
wireless event, it transmits a Supervision Loss report.
12h
1-24h
Jamming Alert
Alarm and report when the receiver is jammed
-
-
Enrollment-
Any Event
Selected: any event (detection, tamper) can be used for enrollment.
Cleared: only “Enrollment” event can be used for enrollment.
2) Enroll and delete
This menu includes the Detectors , Keyfobs , Sirens Repeaters , and Arming Stations sub-menus.
Detectors
Parameter
Description
Enroll
The selected zone is the next available one. Press * or # to scroll.
1) Manual:
Serial no.: enter the peripheral’s serial number (printed on the
product’s label). To enter a letter (A-F), press the asterisk key
repeatedly.
Additional zone: enter the second zone number for the following
peripherals: door contact (DCM)8, Smoke/Heat DSH detector.
Enroll: press to enroll the detector.
8
When using the additional zone of the door contact, the first zone must be enrolled, even if it is not going to
be used. After enrolling the two zones, the first zone can be deleted and re-used.

FORCE Series Installation Guide
18 PIMA Electronic Systems
Parameter
Description
2) Auto: activate the detector; see Enrollment-Any Event above.
Status: the system is waiting for a signal, or displays the received
detector.
Enroll: press to enroll the detector, or if multiple detectors are
received, scroll between them using the left-right arrow keys and
press Enroll .
Delete
1) Delete: press * or # to select a zone.
Press Delete to delete the selected zone.
2) Delete All: Press Delete to delete all the defined zones.
Keyfobs
Parameter
Description
Enroll
The selected User is the next available one. Press * or # to scroll.
1) Manual:
Serial no.: enter the device’s serial number (printed on the product’s
label). To enter a letter (A-F), press the asterisk key repeatedly.
Enroll: press to enroll a keyfob to the selected user.
2) Auto: press any keyfob button.
Status: the system is waiting for a signal, or displays the received
keyfob.
Enroll: press to enroll the keyfob, or if multiple keyfobs are
received, scroll between them using the left-right arrow keys and
press Enroll .
Delete
1) Delete: press * or # to select a user (printed on the product’s label). To
enter a letter (A-F), press the asterisk key repeatedly..
Press Delete to delete the selected keyfob.
2) Delete All: Press Delete to delete all the defined keyfob from all users.
Sirens
Parameter
Description
Enroll
1) Manual:
Serial no.: enter the siren’s serial number.
Enroll: press to enroll a keyfob to the selected user.
2) Auto: press the siren’s enrollment button.
Status: the system is waiting for a signal, or displays the received
siren.
Enroll: press the siren’s enrollment button.
Delete
1) Delete: press * or # to select a user.
Press Delete to delete the selected keyfob.
2) Delete All: Press Delete to delete all the defined keyfobs from all users.

4: Peripherals
PIMA Electronic Systems 19
Repeaters
Parameter
Description
Enroll
1) Manual:
Serial no.: enter the device’s serial number.
Enroll: press to enroll the repeater.
2) Auto: the selected repeater is the next available one. Press * or # to
scroll, and press the enrollment button on the repeater.
Status: the system is waiting for a signal, or displays the received
repeater/s.
Enroll: press to enroll the repeater, or, if multiple repeaters are
received, scroll between them using the left-right arrow keys and
press Enroll .
Delete
1) Delete: press * or # to select a repeater.
Press Delete to delete the selected repeater.
2) Delete All: Press Delete to delete all the defined repeaters.
Arming Stations
Parameter
Description
Enroll
1) Manual:
press * or # to select a device.
Serial no.: enter the device’s serial number.
Enroll: press to enroll the device.
2) Auto: the selected arming station is the next available one. Press * or #
to scroll, and press the enrollment button on the device.
Status: the system is waiting for a signal, or displays the received
device/s.
Enroll: press to enroll the device, or, if multiple devices are
received, scroll between them using the left-right arrow keys and
press Enroll .
Delete
1) Delete: press * or # to select a device.
Press Delete to delete the selected arming station.
2) Delete All: Press Delete to delete all the defined arming stations.
Settings
1) Partitions: for each arming station, select its partitions.
2) Name: user text, up to 28 characters.

FORCE Series Installation Guide
20 PIMA Electronic Systems
5Zones
The Zones menu includes the following sub-menus:
1) Zone Settings; see below.
2) Zone Type Settings; see section 6), on page 21.
3) Copy Zones; see section 5.3, on page 22.
4) Partitions Names; see section 5.3.2, on page 22.
5.1 Zone Settings
System Configuration  Zones  Zone Settings
Press * or # to select a zone.
1) Type: select the zone type from the list; see the list below.
2) Name: user text, up to 28 characters.
3) Delay/24H: select from the following options.
Parameter
Description
Instant
Opening this zone while the system is armed will trigger the alarm instantly.
Entry Delay #1-2
Opening this zone while the system is armed will trigger the alarm only
after this delay elapses, unless the system is meanwhile disarmed.
Delay Follower
Opening this zone while the system is armed will not trigger the alarm as
long as the entry delay has not expired. If the delay elapses and the zone
is still open, the alarm will be set off.
24 Hour
This zone is constantly armed, regardless of the system state of arming.
In use mostly with smoke detectors and panic keys.
4) Attributes: select from the following list.
Parameter
Description
Disabled
The zone is permanently inactive.
Normally Open
Selected: Normally Open zone
Unselected: Normally Close zone
Allocated to
Home 1-4
Select to which Home partial arming mode this zone will be allocated to.
Multiple selection is allowed.
EOL Supervision
Select if the zone will be supervised for cut and/or short9.
Chime Zone
This zone will trigger the keypad buzzer, whenever it is opened while
the system is disarmed. Also triggered is the Chime Activation
programmed output type.
Roller Blinds
Select to adjust the zone’s sensitivity to roller blinds.
5) False Alarms: select from the list that follows ( Inactive is also an option).
Parameter
Description
Double Knock
This zone will trigger the alarm only if two pulses are detected during the
Double Knock time (see 9, on page 32).
Cross Zoning
This zone will trigger the alarm when opened, only if other cross zone is
opened too, during the Cross Zoning time (see 9, on page 32).
9
Depending on the defined number of resistors. See 10, on page 42.