Pima Hunter-Pro 32 User manual

HUNTER-PRO 32
Intruder Alarm
System
User Manual
PIMA Electronic Systems Ltd.
5 Hatzoref Street, Holon 58856, Israel
℡[phone] [phone]
[e-mail] http://www.pima-alarms.com

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
2
PIMA Electronic Systems Ltd. does not represent that its Product may not
be compromised and/or circumvented, or that the Product will prevent
any death, personal and/or bodily injury and/or damage to property
resulting from burglary, robbery, fire or otherwise, or that the Product will
in all cases provide adequate warning or protection. The User
understands that a properly installed and maintained equipment may only
reduce the risk of events such as burglary, robbery, and fire without
warning, but it is not insurance or a guarantee that such will not occur or
that there will be no death, personal damage and/or damage to property
as a result.
PIMA Electronic Systems Ltd. shall have no liability for any
death, personal and/or bodily injury and/or damage to property
or other loss whether direct, indirect, incidental, consequential
or otherwise, based on a claim that the Product failed to
function.
Warning: The user should follow the installation and operation
instructions and among other things test the Product and the whole
system at least once a week. For various reasons, including, but not
limited to, changes in environment conditions, electric or electronic
disruptions and tampering, the Product may not perform as expected.
The user is advised to take all necessary precautions for his/her safety
and the protection of his/her property.
This document may not be duplicated, circulated, altered, modified,
translated, reduced to any form or otherwise changed; unless PIMA’s
prior written consent is granted.
All efforts have been made to ensure that the content of this manual is
accurate. Pima retains the right to modify this manual or any part
thereof, from time to time, without serving any prior notice of such
modification.
Please read this manual in its entirety before attempting to program or
operate your system. Should you misunderstand any part of this manual,
please contact the supplier or installer of this system.
Copyright 2004 by PIMA Electronic Systems Ltd. All rights reserved.
You can contact us at: PIMA Electronic Systems Ltd., 5 Hatzoref St.,
Holon 58856, Israel. http://www.pima-alarms.com

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
3
TABLE OF
CONTENTS
CHAPTER 1: INTRODUCTION .................................................4
1.1 Main Features HUNTER-PRO 32 .........................................5
1.2 Safety Precautions ............................................................5
1.3 Signs and Abbreviations Key ..............................................6
CHAPTER 2: KEYPADS ............................................................7
2.1 Display Screen ..................................................................8
2.2 Keys’ Function ................................................................10
2.3 Entering User Menu.........................................................11
CHAPTER 3: ARMING & DISARMING THE SYSTEM ..............13
3.1 Arming/Disarming via Keypad ..........................................14
3.2 Arming/Disarming with Remote Control ...............................16
3.3 Arming/Disarming with Key..............................................17
3.4 Automatic Arming ...........................................................17
3.5 Disarming the System .....................................................19
3.6 Remote Control via Touch-tone Phone ...............................20
CHAPTER 4: PROGRAMMING AND OPERATION...................22
4.1 Programming Codes ........................................................22
4.2 Programming Time and Date ...........................................31
4.3 Private Dialer Telephone Numbers ...................................31
4.4 Chime ............................................................................33
4.5 Alarm .............................................................................34
4.6 Panic..............................................................................35
4.7 Smoke and Fire Detectors Alarm ......................................35
4.8 System Tests ..................................................................35
4.9 Canceling Keypad Buzzer .................................................36
4.10 Bypassing Zones............................................................36
4.11 Memory Log ..................................................................36
4.12 System Display Types ....................................................38
CHAPTER 5: TROUBLESHOOTING ..............................................40

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
4
CHAPTER 1:
INTRODUCTION
Congratulations on your purchase of the HUNTER-PRO 32 Intruder
Alarm System! Much care has been taken in developing the
HUNTER-PRO Intruder alarm system, which will provide you with
unprecedented peace of mind. The HUNTER-PRO user-friendly
operation and advanced features will professionally protect your
home or business.
HUNTER-PRO 32 Intruder Alarm System contains numerous features
that allow it to befit the customer’s individual needs, and yet remain
easy to program and use both by the customer and the technician.
Therefore, it is important to read this manual from cover to cover in
order to familiarize yourself with the system and take full advantage
of its features. To assure optimal safety and security, you should
test the HUNTER-PRO 32 Intruder Alarm System once a week.
For any further questions, please do not hesitate to contact your
local PIMA distributor or PIMA directly at:
PIMA Electronic Systems Ltd.
Tel.: [phone]
Fax: [phone]
Email: [email protected]om
Up to date literature is available to download from our website:
www.pima-alarms.com

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
5
1.1 Main Features HUNTER-PRO 32
 8 to 32 zones with wireless add-on, local, and remote bus expanders
 Supports a wide range of partition options:
 Up to 16 partitions each with it own Account ID and Users
 Up to 8 subsystems each with different keypads, IDs, etc.
 Full supervision data of wireless detectors (life signal, low battery,
fault)
 Comprehensive Zone Tests for flawless installation: Walk Test, Soak
Test, etc.
 Two options for viewing system status:
 “PIMA” Style: Status of all 32 zones is displayed
simultaneously
 Detailed: Scrolling events, zones’ and system’s status
 Four Subscriber dialing numbers with optional voice message
 Four Monitoring Stations phone numbers
 PIMA unique Integrated Digital Communicator (telephone, long-range
radio)
 Supports split and double reporting with different account IDs
 LCD keypad with multilingual Menu-Driven screens for easy
programming and operation
 Many alternatives for easy programming (Keypad, Fast Programmer,
Local/Remote download software)
 Up to 28 user codes with various authorization levels
 Easy and user friendly operation with single key operation
 Various accessories (microphone, voice unit etc.)
 Memory Log up to 410 events (100 are non-volatile)
 Automatic Arming at a preset time and/or after a preset silence time
 System remote control via any touchtone telephone
1.2 Safety Precautions
Your Hunter alarm system has been registered with the CE in
accordance with EN 60950 of its rules. The CE requires us to tell you
the following information:

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
6
 To reduce the risk of fire or electric shock, do not expose this
alarm system to rain or moisture.
 Do not open the door of the alarm system. Dangerous high
voltages are present inside of the enclosure. Refer servicing to
qualified personnel only.
 This alarm system should be used with AC 230V, 50Hz. To
prevent electric shocks and fire hazards, do NOT use any other
power source.
 Do not spill liquid of any kind onto the unit. If liquid is
accidentally spilled onto the unit, immediately consult a qualified
service.
 Install this product in a protected location where no one can trip
over any line or power cored. Protect cords from damage or
abrasion.
 Disconnect all sources of power supply before proceeding with
the installation.
 Connect the AC wires to the terminal block on the PCB as
marking. Pay attention to polarity.
1.3 Signs and Abbreviations Key
Regular key press
Long key press, until confirmation beep is heard
Press this key at any programming stage in order to
return to root screen
Default Master Code: 5555
Enabled User Code: A code enabled, by Master Code, to enter
User Menus
LCD Zone Numbers: Referring to the frame of zones engraved
above and below the LCD display window,
indicating the zones’ numbers.

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
7
CHAPTER 2:
KEYPADS
HUNTER-PRO 32 works with PIMA’s LCD keypads: RXN-400 and
RXN-41O, especially designed for maximum simplicity, durability and
decorative design. The keypad is used for arming, disarming and
programming the system as well as displaying time and date, system
status information, events and defaults, memory log and more.
Both keypad models are identical, except for the size of the display
screen:
 RXN-410: Large screen 23 x 97 mm
 RXN-400: Small screen 15 x 60 mm
 Up to eight keypads can be connected to the system
1 JAN 04 12:40
RXN-410
S
y
stem dis
p
la
y
:
Date & Time
ARM LED
(green)
Fault LED
(red)
System display:
Zones Status
Num & Function
keys
Navigation &
Programming
ke
y
s

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
8
2.1 Display Screen
The display screen has two lines with 16 characters each. The upper
line displays the time and the date. The lower line displays data
regarding the system, such as events, faults and zone status.
The user can choose between two display types: scrolling (fast zone
display) and PIMA display:
2.1.1 Scrolling
The zone and event screens automatically interchange and display
their status in a chronological order.
17
18
19
2
0
21
2
2
23
24 25 26 27 28 29 30 31 32
4 J A N 04 PS00:22
Vo l t a ge
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Upper Line Display
 Time and date
 System status displayed between time and date:
PSystem communicating or testing PSTN line
SSiren ON
RRelay ON
TSystem reporting to Monitoring Station via radio transmitter
Lower Line Display
 Events and faults
 Opened zones (OP)
T
ime
Date
Event/Faul
t
S
y
stem status

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
9
2.1.2 PIMA Display
All events and zones displayed in a single screen using signs and
abbreviations
17
18
19
2
0
21
2
2
23
24 25 26 27 28 29 30 31 32
4 J A N 04 PS00:22
-B
_
- - F--
_
-------
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Upper Line Display
Time and date if system has 16 or les zones. If more, upper line
displays data like the lower line.
Lower Line Display
The following signs appear above (or below when in upper line) the
zone number/partitions that encircle the LCD screen:
-Closed zone
_Opened zone
BBypassed zone
AAlarm zone (zone triggering alarm)
CChime zone
SShortcut zone (zone was shortcut)
FFailed zone (disconnected)/Tamper event (in a wireless
detector)
LLow battery in wireless detector
VSupervision signal: Wireless detector did nor report test to
system
T
imeDate
Zone Status and Events
System
status

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
10
NOTE:
If technician selected PIMA display, the system will not display the
zone status during faults. Only after faults resolved, PIMA Display
renews.
2.2 Keys’ Function
Operating and programming the system commences by first entering the
Master Code and then pressing any further required keys. However, a
number of keys enable certain actions by a single long press, without the
Master Code:
Function
Key After entering Master Code
(short press)
Secondary Function
(long press)
System Arming/Disarming Fast arming the system (if
enabled by technician)
Display arming, alarm, and fault
histories -
Temporary bypass of zones -
Arming the system to mode “Home
1” (partial arming)
Fast arming the system to
“Home 1” mode (if enabled by
technician)
Display menu (see section “Zone
Status Display”) -
Programming telephone numbers -
Arming the system to mode “Home 2”
(partial arming)
Fast arming the system to
“Home 2” mode (if enabled by
technician)
Programming time and date -
Programming the user codes -
Programming zones for Chime feature Enabling/Disabling the Chime
feature
Programming automatic arming -
Programming key Smoke detector reset

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
11
Programming key -
Programming key Display service Provider
information
 Programming key
 Test siren, battery, AC, and tel.
line
-
Programming key Display system’s name and
version
2.3 Entering User Menu
In order to program and change data in the user level, you must first
enter the User Menu. User Menu can be fully accessed by the system
administrator (owner) when using the Master Code.
Other users can also access the User Menu but are limited to the
number of available functions according to their authorization level
programmed by the system administrator (owner).
To learn more about authorization levels and how to change them
see “Programming Codes” on page 22
2.3.1 Entering User Menu with Master Code
To access the User Menu:
Master Code User Menu
Choose 1,2... Function key (see page
10)
2.3.2 Entering User Menu with User Code
If user is enabled by technician to enter the User Manu:
User Code User Menu
Choose 1,2...
Function key (see page 10)
If user is not enabled by technician to enter the User Menu (i.e.,
User Code arms/disarms the system), the menu can still be accessed
as follows:

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
12
User Code User Menu
Choose 1,2... Function key
(see
page 10)
When user selects a function (i.e., the corresponding key is pressed)
that he or she does not authorized to, the system displays the
following:
Access Denied!
Press END 

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
13
CHAPTER 3:
ARMING &
DISARMING
THE SYSTEM
The system can be armed and disarmed using one of four methods:
 Keypad
 Remote control or key
 Automatically (arming only)
 Remotely via telephone
As a rule, the system should be armed ONLY when all zones (but
those on the exit route) are closed and there are no faults (e.g.,
battery, mains, etc.) and/or events (e.g., fire, panic, etc.). It is
possible to arm the system with open zones but these zones should
be bypassed for the system to be armed (see “Arming with Open
Zones” on page 14).
IMPORTANT!
When a zone is bypassed, it will NOT produce an alarm in case an
intruder will be detected at that zone.
The technician should enable the option to auto-bypass open zones
when the system is armed remotely (remote control, key, or via the
phone) or when the system is auto-armed. If not enabled, the
system will not arm with open zones.
IMPORTANT!
When automatic-bypass is enabled, you will have NO indication
when arming the system remotely.

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
14
3.1 Arming/Disarming via Keypad
3.1.1 System Messages During Arming
3.1.1.1 Arming with Closed Zones (normal arming)
Before arming the system, make sure all zones (except exit delayed
zones – usually zones on exit route) are closed: make sure that in
the keypad display above/below all the LCD zones numbers there is
not a _sign blinking or an opened zone indication.
The system can be activated using one of the following codes:
Master Code, User Code, and Short Code.
After entering one of these codes, the green control LED shall begins
to blink, a beep will be heard from the keypad, and the display will
show the exit delay message:
Arming...
Exit Delay 25
At the end of the exit delay, the green control LED shall stop to blink
and stay on, the beep will stop, and the display will show the
following message: “System Set” and then change to the
following display (example):
1 JAN 04 20:05
3.1.1.2 Arming with Open Zone(s)
When activating the system with one or more opened zones (that
are not on the exit route, i.e., exit delayed zones), the keypad will
produce a fast-beep and the display will show:
Open Zone! Press
OP:TOM OOM …
Bypass or END
OP:F ONT DOO
To bypass open zones: open zones are bypassed & system
armed
Scrolling line: Open Zones & Events

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
15
To cancel arming: system returns to normal operation
mode
3.1.2 Arming with Master Code
Master Code … User Menu
Choose 1,2... 
NOTE:
The system’s default Master Code is: 5555
3.1.3 Fast arming with User Code and/or Short Code
Pressing the code shall arm the system immediately:
Short Code
User Code
3.1.4 Arming the System to HOME state
Arming to “HOME 1”: Short Code or User Code or Master
Code
Arming to “HOME 2”: Short Code or User Code or Master
Code
NOTE:
After long pressing the HOME key (i.e. or ) and
entering the short/user/master code, the following message is
displayed: HOME 1 or HOME 2 according to the pressed key
3.1.5 Fast Arming
To quickly arm the system, if enabled by technician:
 Full Arming: 

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
16
 Arming HOME 1: 
 Arming HOME 2: 
NOTE:
Exit delays in HOME 1 and HOME 2 can be disabled by technician.
3.1.6 Arming via the User Menu
If user is enabled by technician to enter the User Manu:
User Code User Menu
Choose 1,2... 
If user is not enabled by technician to enter the User Menu, it can
still be accessed as follows:
User Code User Menu
Choose 1,2... 
3.2 Arming/Disarming with Remote
Control
Optional feature.
REM-3 remote control has three buttons: arming, disarming, and
HOME 1. Turn to the technician in order to install this feature.
NOTE:
REM-3 is only available for HUNTER-PRO with wireless add-on
system.
The remote is a Code-Hopping type (i.e., the code is changed with
each operation and thus prevents “code stealing”) with a key holder
for carrying with ones keys.

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
17
ARM:
To arm the alarm system, press the GREEN
button on the remote control.
DISARM:
To disarm the alarm system, press the RED
button on the remote control.
HOME MODE:
To arm the alarm system in a Home Mode,
press the BLUE button.
PANIC:
To send a panic signal to the alarm system,
press the BLUE and GREEN buttons together for
3 seconds.
NOTE:
It is possible for the technician to program the system to produce a
short beep when the system is armed with the remote control.
Doing so, the user can also get indication if the remote control’s
battery is low.
3.3 Arming/Disarming with Key
HUNTER-PRO 32 can be armed/disarmed with a key. Turn to the
technician in order to install this feature.
NOTE:
It is possible for the technician to program the system to produce a
short and beep when the system is armed with the key.
3.4 Automatic Arming
The system can be automatically armed with one of the following
two options: 1. At a preset time; 2. After no-detection period.
At the preset time or after no-detection period, the system will
commence auto-arming unless it was armed before that time. This
feature is valid for all weekdays.

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
18
The system can detect movement in the protected area via its
connected detectors and sensors, therefore, it can identify no-
movement hence there is no one in the protected area.
When the system starts auto-arming, the display will show
“Automatic Arming” and a 45 seconds ‘warning countdown’ will start,
indicating the arming countdown is to follow. Note that during the
‘warning countdown’ the keypad will beep. During the ‘warning
countdown’, any disarming code can cancel the auto-arming process.
After the ‘warning countdown’ is over, the system will begin regular
arming process, including exit delay and a beep from the keypad.
3.4.1 Programming Auto-Arming at Preset time
Master Code /Enabled User Code User Menu
Choose 1,2... 
-OR-
User Code User Menu
Choose 1,2... 
The following screen will appear:
Automatic Arming
ENTE /NEXT/END
Press and move to the next screen:
Automatic Arming
XX:XX
Enter Time in which the system will be armed
NOTE:
To cancel Auto-Arming, the Automatic Arming programming needs to be
repeated, and the time to be set as 00:00.
Press to save programming and move to the next screen.

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
19
3.4.2 Programming Auto-Arming after no-detection
period
Master Code /Enabled User Code User Menu
Choose 1,2... 
-OR-
User Code User Menu
Choose 1,2... 
In the following screen, enter the no-detection period (in minutes)
that after which the system commence auto-arming:
Silence Time
X Minutes Silence Time in minutes
Press to save programming and move to the next screen.
3.5 Disarming the System
3.5.1 Disarming the System with Master Code
Master Code User Menu
Choose 1,2... 
3.5.2 Disarming the System with User Code
User Code
Entering the code will immediately disarm the system.
-OR-
Enabled User Code User Menu
Choose 1,2... 
-OR-

HUNTER-PRO 32 Intruder Alarm System - Installation Manual
20
User Code User Menu
Choose 1,2... 
NOTE:
If the system does not turn to Disarm state, make sure that the time is included
in the preset time frame that enables disarming the system (see section
“Programming User Codes”)
3.6 Remote Control via Touch-tone
Phone
The alarm system can be remote-controlled via any touch-tone
telephone, including cellular phone. The system can be controlled
from the moment there is communication between the system and
the telephone, whether the system called the telephone, or when
initiated by the user as following described:
1. Dial the telephone number the system is connected to
2. Wait for the system’s confirmation tone (a long tone followed
with two beeps)
3. Enter Master Code (note NOT to enter the code before the end
of the confirmation tone)
4. Wait a few seconds until the alarm system confirms its status,
using one of the two following tones:
Continuous tone: System disarmed
beep System armed
NOTE:
The system will not identify commands from the telephone while sounding the
confirmation tone. It is important to wait until to confirmation tone is over
before pressing the telephone keys that control the system.
5. Execute command by pressing a key on the phone.
The following table includes system’s commands by phone keys: