Planet VIP-1000 Series User manual
- 6 - - 7 -
- 5 -
3
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘3’ and the VIP-1000PT/T reports on WAN port subnet mask.
3) Input a new WAN port subnet mask with ‘#’ at the end.
Use ‘*’ to replace ‘.’. User can input 255*255*255*0 to set the new
WAN port subnet mask 255.255.255.0.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
4
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘4’ and the VIP-1000PT/T reports on the current gateway.
3) Input the new gateway and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
gateway 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
5
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘5’ and the VIP-1000PT/T reports on the current DNS.
3) Input the new DNS and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
DNS 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
6
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘6’ and the VIP-1000PT/T reports on ‘Factory reset’.
3) At the prompt, please enter password. Please refer to Operation 1 for
the password input.
6Note
If you want to quit, press ‘**’.
4) Report ‘operation successful’ if password is right and then the
VIP-1000PT/T will be set to factory default.
5) Press ‘7’ to reboot to make changes effective.
7
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘7’ and the VIP-1000PT/T reports on ‘Reboot’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) The VIP-1000PT/T will reboot if password is right and operation is properly
done.
Note
If you want to quit, press ‘**’.
8
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘8’ and the VIP-1000PT/T reports on ‘WAN Port Login’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
Note
If you want to quit, press ‘**’.
4) Report ‘Operation successful’ if it’s done properly.
5) At the prompt, choose 1 (enable) or 2 (disable) and end with ‘#’.
6) Report ‘operation successful’ if it’s done properly.
9
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘9’ and the VIP-1000PT/T reports on ‘Web Access Port’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) Report ‘operation successful’ if it’s done properly.
5) Report the current Web Access Port.
6) Set the new Web access port and end with ‘#’.
7) Report ‘operation successful’ if it’s done properly.
0
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘0’ and the VIP-1000PT/T reports on the current ‘Firmware
version’.
4. NOTICE
In the Voice menu, press *(asterisk) to return to the up level menu.
If any changes are made in the IP assignment mode, please reboot the VIP-1000PT/T
to take effect the settings.
When entering IP address or subnet mask, input ‘*’ to represent ‘.’ and add ‘#’ to
nish inputting, for example, to enter the IP address 192.168.1.11, press these
keys:192*168*1*11#.
You can enter the password by phone keypad, the matching table between numbers
and letters are as follows:
To input: A,B,C,a,b,c------press ‘2’
To input: D,E,F,d,e,f------press ‘3’
To input: G,H,I,g,h,i------press ‘4’
To input: J,K,L,j,k,l------press ‘5’
To input: M,N,O,m,n,o------press ‘6’
To input: P,Q,R,S,p,q,r,s------press ‘7’
To input: T,U,V,t,u,v------press ‘8’
To input: W,X,Y,Z,w,x,y,z------press ‘9’
To input all other characters in the administration password------press ‘0’.
Press ‘#’(pound) key to indicate that you have nished entering the IP address or
subnet mask or other settings.
When assigning IP address in Static IP mode, customer must set IP address, subnet
mask and default gateway. If in DHCP mode, please make sure that DHCP server is
available in your existing broadband connection to which WAN port of VIP-1000PT/T is
connected.
Further Information
For further conguration, please refer to the user’s manual, which can be downloaded
from the website.
http://www.planet.com.tw/en/support/download.php?type1=372&model=48762&type=3
If you have any other question, please contact the dealer where you
purchased this product or you can contact PLANET directly at the
following email address: support_voip@planet.com.tw
- 1 - - 2 -
- 3 - - 4 -
1. Package Contents
The package should contain the following items plus the VIP-1000PT/T. If any item is
missing or damaged, please contact the seller immediately.
Quick Installation
Guide Handset Handset
Cord RJ45 Cable Power Adapter
(VIP-1000T only) Stand
2. Hardware Installation
Step 1. Handset Connection
Insert one end of the Handset Cord into Handset and the other end into Handset Jack.
Handset
Step 2a. Connecting Power Adapter and Network
Power Adapter (VIP-1000T only)
Network
Switch
Note
Use only the DC 5V 1A power to ensure correct functionality.
Step 2b. Connecting Power via PoE Interface and Network
The VIP-1000PT can be congured without external power if connected to an IEEE802.3af/
at PSE device such as 802.3af/at PoE injector/hub or 802.3af/at PoE switch.
PoE Switch
Note
Only the VIP-1000PT supports 802.3af/at power injection; use of any non-
standard PoE injector could damage the device.
Step 3. Computer Network Setup
Set your computer’s IP address to 172.16.0.x, where x is a number between 2 and 254
(except 1 which is being used for the camera by default). If you don’t know how to do
this, please ask your network administrator.
PC
Step 4. Login Prompt
Use web browser (Internet Explorer 8.0 or above) to connect to 172.16.0.1 (type this
address in the address bar of web browser). You’ll be prompted to input user name and
password: admin and 123, respectively. If you lose an IP of the VIP-1000PT/T, please
refer to the description below to get the IP via panel button.
****
Choose
Start IVR
VIP-1000PT/T
0 Check Status
9 Web Access Port
8 WAN Port Login
7 Reboot
6 Factory Reset
5 DNS
4 Gateway
3 WAN Port Subnet Mask
2 WAN Port IP Address
1 WAN Port Connection
3. IVR Descriptions
Below is the table that lists commands, and descriptions:
Operation
Code Contents
1
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘1’ and the VIP-1000PT/T reports on the current WAN port
connection type.
3) At the prompt, please enter password. User needs to key-in the pound
sign ‘#’ at the end of the password if he wants to congure the WAN port
connection type.
The password for IVR is the same as the one of Web login. User
can use the phone keypad to enter password directly, and follow the
instructions under Notice below.
For example, Web login password is ‘admin’, so password for IVR is
‘admin’, too. User needs to input ‘23646’ to access and then congure
the WAN connection port.
4) Report ‘operation successful’ if password is right.
5) Choose the new WAN port connection type from 1.DHCP and 2.Static (end
with ‘#’).
6) Report ‘operation successful’ if user makes the changes successfully.
Then the VIP-1000PT/T will return with the prompt ‘Please enter your
option, one WAN Port ……’.
Note
1.Add ‘#’ to the end of the password and select the new WAN
port connection type.
2. If you want to quit, press ‘*’.
2
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘2’ and the VIP-1000PT/T reports on the current WAN Port IP
Address.
3) Input the new WAN port IP address and end it with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*168 to set the
new IP address 192.168.20.168.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
1. If you want to quit, press ‘**’.
2. Set the WAN IP and then Subnet Mask, Gateway and DNS
(Operation Code 3, 4 and 5); otherwise, new setting will be
invalid.
- 1 - - 2 -
- 3 - - 4 -
1. Package Contents
The package should contain the following items plus the VIP-1000PT/T. If any item is
missing or damaged, please contact the seller immediately.
Quick Installation
Guide Handset Handset
Cord RJ45 Cable Power Adapter
(VIP-1000T only) Stand
2. Hardware Installation
Step 1. Handset Connection
Insert one end of the Handset Cord into Handset and the other end into Handset Jack.
Handset
Step 2a. Connecting Power Adapter and Network
Power Adapter (VIP-1000T only)
Network
Switch
Note
Use only the DC 5V 1A power to ensure correct functionality.
Step 2b. Connecting Power via PoE Interface and Network
The VIP-1000PT can be congured without external power if connected to an IEEE802.3af/
at PSE device such as 802.3af/at PoE injector/hub or 802.3af/at PoE switch.
PoE Switch
Note
Only the VIP-1000PT supports 802.3af/at power injection; use of any non-
standard PoE injector could damage the device.
Step 3. Computer Network Setup
Set your computer’s IP address to 172.16.0.x, where x is a number between 2 and 254
(except 1 which is being used for the camera by default). If you don’t know how to do
this, please ask your network administrator.
PC
Step 4. Login Prompt
Use web browser (Internet Explorer 8.0 or above) to connect to 172.16.0.1 (type this
address in the address bar of web browser). You’ll be prompted to input user name and
password: admin and 123, respectively. If you lose an IP of the VIP-1000PT/T, please
refer to the description below to get the IP via panel button.
****
Choose
Start IVR
VIP-1000PT/T
0 Check Status
9 Web Access Port
8 WAN Port Login
7 Reboot
6 Factory Reset
5 DNS
4 Gateway
3 WAN Port Subnet Mask
2 WAN Port IP Address
1 WAN Port Connection
3. IVR Descriptions
Below is the table that lists commands, and descriptions:
Operation
Code Contents
1
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘1’ and the VIP-1000PT/T reports on the current WAN port
connection type.
3) At the prompt, please enter password. User needs to key-in the pound
sign ‘#’ at the end of the password if he wants to congure the WAN port
connection type.
The password for IVR is the same as the one of Web login. User
can use the phone keypad to enter password directly, and follow the
instructions under Notice below.
For example, Web login password is ‘admin’, so password for IVR is
‘admin’, too. User needs to input ‘23646’ to access and then congure
the WAN connection port.
4) Report ‘operation successful’ if password is right.
5) Choose the new WAN port connection type from 1.DHCP and 2.Static (end
with ‘#’).
6) Report ‘operation successful’ if user makes the changes successfully.
Then the VIP-1000PT/T will return with the prompt ‘Please enter your
option, one WAN Port ……’.
Note
1.Add ‘#’ to the end of the password and select the new WAN
port connection type.
2. If you want to quit, press ‘*’.
2
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘2’ and the VIP-1000PT/T reports on the current WAN Port IP
Address.
3) Input the new WAN port IP address and end it with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*168 to set the
new IP address 192.168.20.168.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
1. If you want to quit, press ‘**’.
2. Set the WAN IP and then Subnet Mask, Gateway and DNS
(Operation Code 3, 4 and 5); otherwise, new setting will be
invalid.
- 1 - - 2 -
- 3 - - 4 -
1. Package Contents
The package should contain the following items plus the VIP-1000PT/T. If any item is
missing or damaged, please contact the seller immediately.
Quick Installation
Guide Handset Handset
Cord RJ45 Cable Power Adapter
(VIP-1000T only) Stand
2. Hardware Installation
Step 1. Handset Connection
Insert one end of the Handset Cord into Handset and the other end into Handset Jack.
Handset
Step 2a. Connecting Power Adapter and Network
Power Adapter (VIP-1000T only)
Network
Switch
Note
Use only the DC 5V 1A power to ensure correct functionality.
Step 2b. Connecting Power via PoE Interface and Network
The VIP-1000PT can be congured without external power if connected to an IEEE802.3af/
at PSE device such as 802.3af/at PoE injector/hub or 802.3af/at PoE switch.
PoE Switch
Note
Only the VIP-1000PT supports 802.3af/at power injection; use of any non-
standard PoE injector could damage the device.
Step 3. Computer Network Setup
Set your computer’s IP address to 172.16.0.x, where x is a number between 2 and 254
(except 1 which is being used for the camera by default). If you don’t know how to do
this, please ask your network administrator.
PC
Step 4. Login Prompt
Use web browser (Internet Explorer 8.0 or above) to connect to 172.16.0.1 (type this
address in the address bar of web browser). You’ll be prompted to input user name and
password: admin and 123, respectively. If you lose an IP of the VIP-1000PT/T, please
refer to the description below to get the IP via panel button.
****
Choose
Start IVR
VIP-1000PT/T
0 Check Status
9 Web Access Port
8 WAN Port Login
7 Reboot
6 Factory Reset
5 DNS
4 Gateway
3 WAN Port Subnet Mask
2 WAN Port IP Address
1 WAN Port Connection
3. IVR Descriptions
Below is the table that lists commands, and descriptions:
Operation
Code Contents
1
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘1’ and the VIP-1000PT/T reports on the current WAN port
connection type.
3) At the prompt, please enter password. User needs to key-in the pound
sign ‘#’ at the end of the password if he wants to congure the WAN port
connection type.
The password for IVR is the same as the one of Web login. User
can use the phone keypad to enter password directly, and follow the
instructions under Notice below.
For example, Web login password is ‘admin’, so password for IVR is
‘admin’, too. User needs to input ‘23646’ to access and then congure
the WAN connection port.
4) Report ‘operation successful’ if password is right.
5) Choose the new WAN port connection type from 1.DHCP and 2.Static (end
with ‘#’).
6) Report ‘operation successful’ if user makes the changes successfully.
Then the VIP-1000PT/T will return with the prompt ‘Please enter your
option, one WAN Port ……’.
Note
1.Add ‘#’ to the end of the password and select the new WAN
port connection type.
2. If you want to quit, press ‘*’.
2
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘2’ and the VIP-1000PT/T reports on the current WAN Port IP
Address.
3) Input the new WAN port IP address and end it with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*168 to set the
new IP address 192.168.20.168.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
1. If you want to quit, press ‘**’.
2. Set the WAN IP and then Subnet Mask, Gateway and DNS
(Operation Code 3, 4 and 5); otherwise, new setting will be
invalid.
- 1 - - 2 -
- 3 - - 4 -
1. Package Contents
The package should contain the following items plus the VIP-1000PT/T. If any item is
missing or damaged, please contact the seller immediately.
Quick Installation
Guide Handset Handset
Cord RJ45 Cable Power Adapter
(VIP-1000T only) Stand
2. Hardware Installation
Step 1. Handset Connection
Insert one end of the Handset Cord into Handset and the other end into Handset Jack.
Handset
Step 2a. Connecting Power Adapter and Network
Power Adapter (VIP-1000T only)
Network
Switch
Note
Use only the DC 5V 1A power to ensure correct functionality.
Step 2b. Connecting Power via PoE Interface and Network
The VIP-1000PT can be congured without external power if connected to an IEEE802.3af/
at PSE device such as 802.3af/at PoE injector/hub or 802.3af/at PoE switch.
PoE Switch
Note
Only the VIP-1000PT supports 802.3af/at power injection; use of any non-
standard PoE injector could damage the device.
Step 3. Computer Network Setup
Set your computer’s IP address to 172.16.0.x, where x is a number between 2 and 254
(except 1 which is being used for the camera by default). If you don’t know how to do
this, please ask your network administrator.
PC
Step 4. Login Prompt
Use web browser (Internet Explorer 8.0 or above) to connect to 172.16.0.1 (type this
address in the address bar of web browser). You’ll be prompted to input user name and
password: admin and 123, respectively. If you lose an IP of the VIP-1000PT/T, please
refer to the description below to get the IP via panel button.
****
Choose
Start IVR
VIP-1000PT/T
0 Check Status
9 Web Access Port
8 WAN Port Login
7 Reboot
6 Factory Reset
5 DNS
4 Gateway
3 WAN Port Subnet Mask
2 WAN Port IP Address
1 WAN Port Connection
3. IVR Descriptions
Below is the table that lists commands, and descriptions:
Operation
Code Contents
1
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘1’ and the VIP-1000PT/T reports on the current WAN port
connection type.
3) At the prompt, please enter password. User needs to key-in the pound
sign ‘#’ at the end of the password if he wants to congure the WAN port
connection type.
The password for IVR is the same as the one of Web login. User
can use the phone keypad to enter password directly, and follow the
instructions under Notice below.
For example, Web login password is ‘admin’, so password for IVR is
‘admin’, too. User needs to input ‘23646’ to access and then congure
the WAN connection port.
4) Report ‘operation successful’ if password is right.
5) Choose the new WAN port connection type from 1.DHCP and 2.Static (end
with ‘#’).
6) Report ‘operation successful’ if user makes the changes successfully.
Then the VIP-1000PT/T will return with the prompt ‘Please enter your
option, one WAN Port ……’.
Note
1.Add ‘#’ to the end of the password and select the new WAN
port connection type.
2. If you want to quit, press ‘*’.
2
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘2’ and the VIP-1000PT/T reports on the current WAN Port IP
Address.
3) Input the new WAN port IP address and end it with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*168 to set the
new IP address 192.168.20.168.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
1. If you want to quit, press ‘**’.
2. Set the WAN IP and then Subnet Mask, Gateway and DNS
(Operation Code 3, 4 and 5); otherwise, new setting will be
invalid.
- 6 - - 7 -
- 5 -
3
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘3’ and the VIP-1000PT/T reports on WAN port subnet mask.
3) Input a new WAN port subnet mask with ‘#’ at the end.
Use ‘*’ to replace ‘.’. User can input 255*255*255*0 to set the new
WAN port subnet mask 255.255.255.0.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
4
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘4’ and the VIP-1000PT/T reports on the current gateway.
3) Input the new gateway and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
gateway 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
5
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘5’ and the VIP-1000PT/T reports on the current DNS.
3) Input the new DNS and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
DNS 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
6
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘6’ and the VIP-1000PT/T reports on ‘Factory reset’.
3) At the prompt, please enter password. Please refer to Operation 1 for
the password input.
6Note
If you want to quit, press ‘**’.
4) Report ‘operation successful’ if password is right and then the
VIP-1000PT/T will be set to factory default.
5) Press ‘7’ to reboot to make changes effective.
7
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘7’ and the VIP-1000PT/T reports on ‘Reboot’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) The VIP-1000PT/T will reboot if password is right and operation is properly
done.
Note
If you want to quit, press ‘**’.
8
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘8’ and the VIP-1000PT/T reports on ‘WAN Port Login’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
Note
If you want to quit, press ‘**’.
4) Report ‘Operation successful’ if it’s done properly.
5) At the prompt, choose 1 (enable) or 2 (disable) and end with ‘#’.
6) Report ‘operation successful’ if it’s done properly.
9
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘9’ and the VIP-1000PT/T reports on ‘Web Access Port’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) Report ‘operation successful’ if it’s done properly.
5) Report the current Web Access Port.
6) Set the new Web access port and end with ‘#’.
7) Report ‘operation successful’ if it’s done properly.
0
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘0’ and the VIP-1000PT/T reports on the current ‘Firmware
version’.
4. NOTICE
In the Voice menu, press *(asterisk) to return to the up level menu.
If any changes are made in the IP assignment mode, please reboot the VIP-1000PT/T
to take effect the settings.
When entering IP address or subnet mask, input ‘*’ to represent ‘.’ and add ‘#’ to
nish inputting, for example, to enter the IP address 192.168.1.11, press these
keys:192*168*1*11#.
You can enter the password by phone keypad, the matching table between numbers
and letters are as follows:
To input: A,B,C,a,b,c------press ‘2’
To input: D,E,F,d,e,f------press ‘3’
To input: G,H,I,g,h,i------press ‘4’
To input: J,K,L,j,k,l------press ‘5’
To input: M,N,O,m,n,o------press ‘6’
To input: P,Q,R,S,p,q,r,s------press ‘7’
To input: T,U,V,t,u,v------press ‘8’
To input: W,X,Y,Z,w,x,y,z------press ‘9’
To input all other characters in the administration password------press ‘0’.
Press ‘#’(pound) key to indicate that you have nished entering the IP address or
subnet mask or other settings.
When assigning IP address in Static IP mode, customer must set IP address, subnet
mask and default gateway. If in DHCP mode, please make sure that DHCP server is
available in your existing broadband connection to which WAN port of VIP-1000PT/T is
connected.
Further Information
For further conguration, please refer to the user’s manual, which can be downloaded
from the website.
http://www.planet.com.tw/en/support/download.php?type1=372&model=48762&type=3
If you have any other question, please contact the dealer where you
purchased this product or you can contact PLANET directly at the
following email address: support_voip@planet.com.tw
- 6 - - 7 -
- 5 -
3
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘3’ and the VIP-1000PT/T reports on WAN port subnet mask.
3) Input a new WAN port subnet mask with ‘#’ at the end.
Use ‘*’ to replace ‘.’. User can input 255*255*255*0 to set the new
WAN port subnet mask 255.255.255.0.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
4
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘4’ and the VIP-1000PT/T reports on the current gateway.
3) Input the new gateway and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
gateway 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
5
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘5’ and the VIP-1000PT/T reports on the current DNS.
3) Input the new DNS and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
DNS 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
6
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘6’ and the VIP-1000PT/T reports on ‘Factory reset’.
3) At the prompt, please enter password. Please refer to Operation 1 for
the password input.
6Note
If you want to quit, press ‘**’.
4) Report ‘operation successful’ if password is right and then the
VIP-1000PT/T will be set to factory default.
5) Press ‘7’ to reboot to make changes effective.
7
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘7’ and the VIP-1000PT/T reports on ‘Reboot’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) The VIP-1000PT/T will reboot if password is right and operation is properly
done.
Note
If you want to quit, press ‘**’.
8
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘8’ and the VIP-1000PT/T reports on ‘WAN Port Login’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
Note
If you want to quit, press ‘**’.
4) Report ‘Operation successful’ if it’s done properly.
5) At the prompt, choose 1 (enable) or 2 (disable) and end with ‘#’.
6) Report ‘operation successful’ if it’s done properly.
9
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘9’ and the VIP-1000PT/T reports on ‘Web Access Port’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) Report ‘operation successful’ if it’s done properly.
5) Report the current Web Access Port.
6) Set the new Web access port and end with ‘#’.
7) Report ‘operation successful’ if it’s done properly.
0
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘0’ and the VIP-1000PT/T reports on the current ‘Firmware
version’.
4. NOTICE
In the Voice menu, press *(asterisk) to return to the up level menu.
If any changes are made in the IP assignment mode, please reboot the VIP-1000PT/T
to take effect the settings.
When entering IP address or subnet mask, input ‘*’ to represent ‘.’ and add ‘#’ to
nish inputting, for example, to enter the IP address 192.168.1.11, press these
keys:192*168*1*11#.
You can enter the password by phone keypad, the matching table between numbers
and letters are as follows:
To input: A,B,C,a,b,c------press ‘2’
To input: D,E,F,d,e,f------press ‘3’
To input: G,H,I,g,h,i------press ‘4’
To input: J,K,L,j,k,l------press ‘5’
To input: M,N,O,m,n,o------press ‘6’
To input: P,Q,R,S,p,q,r,s------press ‘7’
To input: T,U,V,t,u,v------press ‘8’
To input: W,X,Y,Z,w,x,y,z------press ‘9’
To input all other characters in the administration password------press ‘0’.
Press ‘#’(pound) key to indicate that you have nished entering the IP address or
subnet mask or other settings.
When assigning IP address in Static IP mode, customer must set IP address, subnet
mask and default gateway. If in DHCP mode, please make sure that DHCP server is
available in your existing broadband connection to which WAN port of VIP-1000PT/T is
connected.
Further Information
For further conguration, please refer to the user’s manual, which can be downloaded
from the website.
http://www.planet.com.tw/en/support/download.php?type1=372&model=48762&type=3
If you have any other question, please contact the dealer where you
purchased this product or you can contact PLANET directly at the
following email address: support_voip@planet.com.tw
- 6 - - 7 -
- 5 -
3
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘3’ and the VIP-1000PT/T reports on WAN port subnet mask.
3) Input a new WAN port subnet mask with ‘#’ at the end.
Use ‘*’ to replace ‘.’. User can input 255*255*255*0 to set the new
WAN port subnet mask 255.255.255.0.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
4
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘4’ and the VIP-1000PT/T reports on the current gateway.
3) Input the new gateway and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
gateway 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
5
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘5’ and the VIP-1000PT/T reports on the current DNS.
3) Input the new DNS and end with ‘#’.
Use ‘*’ to replace ‘.’. User can input 192*168*20*1 to set the new
DNS 192.168.20.1.
Press the ‘#’ key to indicate that you have nished.
4) Report ‘operation successful’ if it’s done properly.
Note
If you want to quit, press ‘**’.
6
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘6’ and the VIP-1000PT/T reports on ‘Factory reset’.
3) At the prompt, please enter password. Please refer to Operation 1 for
the password input.
6Note
If you want to quit, press ‘**’.
4) Report ‘operation successful’ if password is right and then the
VIP-1000PT/T will be set to factory default.
5) Press ‘7’ to reboot to make changes effective.
7
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘7’ and the VIP-1000PT/T reports on ‘Reboot’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) The VIP-1000PT/T will reboot if password is right and operation is properly
done.
Note
If you want to quit, press ‘**’.
8
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘8’ and the VIP-1000PT/T reports on ‘WAN Port Login’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
Note
If you want to quit, press ‘**’.
4) Report ‘Operation successful’ if it’s done properly.
5) At the prompt, choose 1 (enable) or 2 (disable) and end with ‘#’.
6) Report ‘operation successful’ if it’s done properly.
9
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘9’ and the VIP-1000PT/T reports on ‘Web Access Port’.
3) At the prompt, please enter password. Refer to Operation 1 for the
password input.
4) Report ‘operation successful’ if it’s done properly.
5) Report the current Web Access Port.
6) Set the new Web access port and end with ‘#’.
7) Report ‘operation successful’ if it’s done properly.
0
1) Pick up phone and press ‘****’ to start IVR.
2) Choose ‘0’ and the VIP-1000PT/T reports on the current ‘Firmware
version’.
4. NOTICE
In the Voice menu, press *(asterisk) to return to the up level menu.
If any changes are made in the IP assignment mode, please reboot the VIP-1000PT/T
to take effect the settings.
When entering IP address or subnet mask, input ‘*’ to represent ‘.’ and add ‘#’ to
nish inputting, for example, to enter the IP address 192.168.1.11, press these
keys:192*168*1*11#.
You can enter the password by phone keypad, the matching table between numbers
and letters are as follows:
To input: A,B,C,a,b,c------press ‘2’
To input: D,E,F,d,e,f------press ‘3’
To input: G,H,I,g,h,i------press ‘4’
To input: J,K,L,j,k,l------press ‘5’
To input: M,N,O,m,n,o------press ‘6’
To input: P,Q,R,S,p,q,r,s------press ‘7’
To input: T,U,V,t,u,v------press ‘8’
To input: W,X,Y,Z,w,x,y,z------press ‘9’
To input all other characters in the administration password------press ‘0’.
Press ‘#’(pound) key to indicate that you have nished entering the IP address or
subnet mask or other settings.
When assigning IP address in Static IP mode, customer must set IP address, subnet
mask and default gateway. If in DHCP mode, please make sure that DHCP server is
available in your existing broadband connection to which WAN port of VIP-1000PT/T is
connected.
Further Information
For further conguration, please refer to the user’s manual, which can be downloaded
from the website.
http://www.planet.com.tw/en/support/download.php?type1=372&model=48762&type=3
If you have any other question, please contact the dealer where you
purchased this product or you can contact PLANET directly at the
following email address: [email protected]
This manual suits for next models
2
Table of contents
Other Planet IP Phone manuals
Planet
Planet VIP-5060PT User manual
Planet
Planet VIP-6040PT User manual
Planet
Planet VIP-321 User manual
Planet
Planet VIP-100T User manual
Planet
Planet VIP-254NT User manual
Planet
Planet VIP-150T User manual
Planet
Planet VIP-103PT User manual
Planet
Planet VIP-255PT User manual
Planet
Planet VIP-193 User manual
Planet
Planet VIP-6040PT User manual
Planet
Planet VIP-362WT User manual
Planet
Planet VIP-103PT User manual
Planet
Planet VIP-256T User manual
Planet
Planet VIP-351PT User manual
Planet
Planet VIP-1140PT User manual
Planet
Planet VIP-36EXT User manual
Planet
Planet VIP-5060PT User manual
Planet
Planet VIP-361PE User manual
Planet
Planet SIP IP PHONE VIP-154PT User manual
Planet
Planet VIP-360PT User manual
