Plura PRM-3G Series User manual

USO RESTRITO
®
Operating
Instructions
PRM-3G Series Monitors
PRM-3G Series
PRM-217-3G
PRM-224-3G
PRM-232-3G

USO RESTRITO
[User’s Manual] Page 2
PRECAUTION--------------------------------------------------------------------------------------------------6
1. OVERVIEW------------------------------------------------------------------------------------------------9
2. GENERAL FEATURES -------------------------------------------------------------------------------------9
3. FUNCTIONAL EXPLANATION OF EACH PART ------------------------------------------------------ 10
1) FRONT PANEL ------------------------------------------------------------------------------------------- 10
PRM-224-3G --------------------------------------------------------------------------------------- 10
Front Keys Arrangements ------------------------------------------------------------------------- 10
Front Keys Operations----------------------------------------------------------------------------- 11
Front panel LED Operations----------------------------------------------------------------------- 11
Speaker Out---------------------------------------------------------------------------------------- 12
2) REAR PANEL -------------------------------------------------------------------------------------------- 12
Connection Details -------------------------------------------------------------------------------- 12
DC Battery IN ------------------------------------------------------------------------------------- 13
RJ-45 ----------------------------------------------------------------------------------------------- 13
Interface description------------------------------------------------------------------------------- 14
4. MENU OVERVIEW ------------------------------------------------------------------------------------- 14
1) TO SHOW AND REMOVE THE MENU ---------------------------------------------------------------------- 14
2) TO GO TO THE NEXT LEVEL ------------------------------------------------------------------------------- 14
3) TO GO BACK TO THE PREVIOUS LEVEL --------------------------------------------------------------------- 15
4) TYPICAL MENU OPERATION------------------------------------------------------------------------------ 15
5. BASIC OPERATION ------------------------------------------------------------------------------------ 15
1) TURNING ON THE MONITOR----------------------------------------------------------------------------- 15
2) VOLUME ADJUSTMENT ---------------------------------------------------------------------------------- 15
3) ONSCREEN MENUS LANGUAGE SELECTION--------------------------------------------------------------- 15
6. ON SCREEN MENUS SELECTION AND ADJUSTMENT --------------------------------------------- 16
1) HOW TO ADJUST THE OSD SCREEN ---------------------------------------------------------------------- 16
7. SELECT VIDEO INPUT --------------------------------------------------------------------------------- 17
1) HOW TO SELECT VIDEO SOURCE BY OSD----------------------------------------------------------------- 17
8. PICTURE MENU OPTIONS ---------------------------------------------------------------------------- 18
1) VIDEO MENUS OF EACH INPUT MODES ------------------------------------------------------------------- 18
2) ADJUST------------------------------------------------------------------------------------------------- 18

USO RESTRITO
[User’s Manual] Page 3
3) COLOR TEMPERATURE CONTROL ------------------------------------------------------------------------- 18
4) SCAN ------------------------------------------------------------------------------------------------- 19
5) ASPECT RATIO ------------------------------------------------------------------------------------------ 19
6) ZOOM-------------------------------------------------------------------------------------------------- 19
7) MONO/BLUE ONLY ------------------------------------------------------------------------------------- 20
8) PC MENU (PC MODE ONLY) ----------------------------------------------------------------------------- 20
9) FLIP ---------------------------------------------------------------------------------------------------- 21
10) NR (NOISE REDUCTION) ------------------------------------------------------------------------------ 21
9. AUDIO MENU OPTIONS ------------------------------------------------------------------------------ 21
1) MAIN / SUB AUDIO OUT ------------------------------------------------------------------------------- 21
2) SDI 1/ SDI 2 AUDIO OUTPUT CHANNEL ----------------------------------------------------------------- 21
3) SDI 1 ,/SDI 2 AUDIO GROUP --------------------------------------------------------------------------- 21
4) LEVEL METER ------------------------------------------------------------------------------------------- 22
5) AUDIO LOUDNESS ------------------------------------------------------------------------------------ 23
6) VOLUME------------------------------------------------------------------------------------------------ 23
10. MARKER MENU OPTIONS-------------------------------------------------------------------------- 24
1) MARKER & USER MARKER------------------------------------------------------------------------------- 24
2) SAFETY AREA ------------------------------------------------------------------------------------------- 25
3) CENTER MAKER ----------------------------------------------------------------------------------------- 25
4) MARKER WIDTH ---------------------------------------------------------------------------------------- 25
5) MARKER COLOR ---------------------------------------------------------------------------------------- 25
6) PRESET1 & PRESET2 ------------------------------------------------------------------------------------ 25
11. GPI MENU OPTIONS -------------------------------------------------------------------------------- 26
1) GPI CONTROL & GPI# --------------------------------------------------------------------------------- 26
12. SETUP MENU OPTIONS ---------------------------------------------------------------------------- 27
1) SETUP LOAD & SETUP SAVE ----------------------------------------------------------------------------- 27
2) FUNCTION 1 ~6 ---------------------------------------------------------------------------------------- 27
3) ONSCREEN DISPLAY ------------------------------------------------------------------------------------ 28
OSD Option ---------------------------------------------------------------------------------------- 28
Time code------------------------------------------------------------------------------------------ 28
Under Monitor Display (color: Tally R/G mode action ) ----------------------------------------- 28
Input ID -------------------------------------------------------------------------------------------- 29
SDI Signal state ------------------------------------------------------------------------------------ 29

USO RESTRITO
[User’s Manual] Page 4
4) ADVANCED --------------------------------------------------------------------------------------------- 29
Information ---------------------------------------------------------------------------------------- 30
Control --------------------------------------------------------------------------------------------- 30
Screen Saver --------------------------------------------------------------------------------------- 30
Screen Control ------------------------------------------------------------------------------------- 30
Fan Control ---------------------------------------------------------------------------------------- 31
X768 Mode ---------------------------------------------------------------------------------------- 31
5) CAPTION ----------------------------------------------------------------------------------------------- 31
6) WAVEFORM FORMAT (ONLY SDI MODEL) ----------------------------------------------------------------- 32
Y-Pb-Pr Waveform--------------------------------------------------------------------------------- 32
Y-Waveform + Vector Scope --------------------------------------------------------------------- 32
Double --------------------------------------------------------------------------------------------- 33
Y-Waveform + Vector Scope Trans--------------------------------------------------------------- 33
Vector Color --------------------------------------------------------------------------------------- 34
Line Select ----------------------------------------------------------------------------------------- 34
Line # ---------------------------------------------------------------------------------------------- 34
Line Display ---------------------------------------------------------------------------------------- 34
7) DUAL LINK MODE(SDI ONLY)---------------------------------------------------------------------------- 34
8) SET ID & ACTIVE SET ID -------------------------------------------------------------------------------- 34
13. PIP (PICTURE IN PICTURE) ------------------------------------------------------------------------- 34
1) PIP ON/OFF------------------------------------------------------------------------------------------- 34
2) INPUT SOURCE------------------------------------------------------------------------------------------ 34
3) ASPECT RATIO ------------------------------------------------------------------------------------------ 35
4) POSITION----------------------------------------------------------------------------------------------- 35
5) PIP BLEND --------------------------------------------------------------------------------------------- 36
6) PIP SWAP ---------------------------------------------------------------------------------------------- 36
7) SOUND SELECT ----------------------------------------------------------------------------------------- 36
8) SUB WINDOW FUNCTION ------------------------------------------------------------------------------- 36
14. OSD TREE -------------------------------------------------------------------------------------------- 37
1) Video ------------------------------------------------------------------------------------------------- 38
2) Audio ------------------------------------------------------------------------------------------------- 39
3) MARKER------------------------------------------------------------------------------------------------ 40
4) GPI ---------------------------------------------------------------------------------------------------- 41
5) SETUP -------------------------------------------------------------------------------------------------- 42

USO RESTRITO
[User’s Manual] Page 5
6) PIP ---------------------------------------------------------------------------------------------------- 43

USO RESTRITO
[User’s Manual] Page 6
Precaution
Before operating the set, please read this manual carefully.
WARNING:
To reduce the risks of electric shock don’t remove back cover. No user serviceable parts insi
de. For service refer to qualified service personnel. To prevent fire or shock hazard, do not
expose the rear of the set to water or moisture. Do not rub or strike the Active Matrix LCD with
any harsh materials as this may scratch, mark, or damage the Active Matrix LCD permanently.
CAUTION:
Unauthorized tampering with the inside of the monitor invalidates the warranty.
The manufacturer shall not warrant any damage caused by improper maintenance and/or repair
executed by an authorized third party.
Important safeguards for you and your new product:
Your product has been manufactured and tested with your safety in mind. However, imprope
r use can result in potential electrical shock or fire hazards. To avoid defeating the safeguar
ds that have been built into your new product, please read and observe the following safety
points when installing and using your new product and save them for future reference.
1. Read Instructions
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Take note of Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Disconnect the unit from the electric supply before cleaning. Do not use abrasive
cleaners. Use a damp cloth for cleaning.

USO RESTRITO
[User’s Manual] Page 7
6. Water and Moisture
Do not use this unit near water.
7. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force
and uneven surfaces may cause the product and cart combination to overturn.
8. Attachments
Do not use any third party attachments not recommended by PLURA. as this may cause
hazards.
9. Ventilation
Do not block any of the ventilation openings.
Install in accordance with the manufacturer ’ s instructions.
10. Power Sources
This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your
dealer.
11. Power Lead Polarization
This product is equipped with a three-wire grounding-type cord. This is a safety feature.
Do not neglect the safety purpose of the grounding-type cord.
12. Power Cord Protection
Power-supply cord should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles and the point where they exit from the product.
13. Outdoor Cable Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection against voltage surges and
built-up static charges. A “ face plate ” also needs to be installed with an isolating
capacitor to prevent any damage from static.
14. Lightning
For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent possible damage to the
product due to lightning and power-line surges.
15. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to
avoid contact with such power lines or circuits, as contact with them might be fatal.

USO RESTRITO
[User’s Manual] Page 8
16. Earthing the product
This product must be earthed properly to comply with the safety regulations in the
country of use. If you are unsure of these regulations, please consult a qualified
electrician.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified
service personnel. If the Set does not operate properly, switch it off and call your dealer.
18. Damage Requiring Service
Isolate this product from the mains supply and refer servicing to qualified service
personnel under the following conditions:
A. If the power-supply cord or plug is damaged.
B. If the glass front has been damaged.
C. If there is ingress of water between the glass and the LCD screen.
D. If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal
operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
19. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to p
erform safety checks to determine that the product is in proper operating condition and t
he front seal is intact .
20. Mounting
The product should be mounted on a wall only as recommended in the instructions.
21. Power
This set operates on an AC supply; the voltage is as indicated on the label on the Manual.
This appliance must be earthed at all times through the chassis as well as through the
power lead.

USO RESTRITO
[User’s Manual] Page 9
1. OVERVIEW
This product is the multi-format Digital LCD Panel to display various kinds of digital video input signal as
HD/SD-SDI Digital and analog signal such as Composite/S-Video/RGB/PC-RGB/DVI/HDMI/Component.
This is also High Definition Broadcasting Monitor which can make it available to do output of stable video
signal with the menu of considering convenient user interface and the easy control for brightness and
color, and by EQ function of HD-SDI input part.
2. GENERAL FEATURES
• HD/SD SDI 2Input / 2Output.
• WAVEFORM / Vector Scope / Time code Display.
- Dual waveform display available
• 16 ch Audio Lever Meter Display. (SDI only)
• Analog & Digital Signal Audio Lever Meter Display.
- Lever Meter Size display selectable (Small or Large)
• Dual Link MODE & 1080p 60 Compatible
• Closed Caption CEA 608, 708, Line 801 & OP-47
• H Flip, H/V Delay.
• Audio Disembedder & Internal Speaker & Headphone out & Monitor out
• Color Temperature – User, VAR, 11000K, 9300K, 6500K, 5400K, 3200K
• Over Scan/Zero Scan/Under Scan/Pixel to Pixel
• PIP (Picture In Picture)/PIP Blend
• Tally LED function (Green/Red/AMBER)
• Integrated DVI (HDCP) function.
• HDMI (HDCP) function.
• Supports VESA DDC2B and a subset of VESA standards.
• Single board is suitable for mounting behind an LCD panel .
• Support RS-232C.
• Support External GPI Control (RJ-45).
• OSD: Graphic based OSD, 7 Languages (UNICODE System).
• LCD Dimming Control
- Manual Dimming Level Control.
•Rack Mount (OPTION)
•Battery Mount (OPTION)
•UMD
•Native Calibration: CA-310, CA-210 (Minolta), K-10 (Klein)
•10bits 3D LUT Color Calibration (BT.709, SMPTE-C, EBU, NTSC, D-Cinema)
•Multi Control(RS-232C)
•Lan To Serial
•Audio Loudness(LKFS)

USO RESTRITO
[User’s Manual] Page 10
3. Functional explanation of each part
1. Front Panel
PRM-224-3G
Front Keys Arrangements
SDI 1 1920x1080I
WAVEFORM
Vector Scope
Center Maker
TC: 00:00:00:00
ANALOG
SDI1
SCAN
MARKER
F1
F2
F3
MENU
SEL/
INPUT
UP
DOWN
STANDBY
ADJUST
SDI2
F5
F6
F4
Audio Level Meter
Speaker
Front Key
LED
Headphone
ND filter hole
Tally LED

USO RESTRITO
[User’s Manual] Page 11
Front Keys Operations
Key Name
Operation
STANDBY
►Power ON/OFF Button. This button is operated after being pressed about 3 seconds.
SEL/INPUT
►Activates OSD menu of input source selecting.
►Changes input source by selecting.
►Executes functions (by OSD help commands) in main OSD menu.
►Activates child menu.
DOWN
►Decreases sound volume of speaker.
►Decreases values of user menu in main OSD menu.
►Executes function (by OSD help commands) in main OSD menu.
UP
►Increases sound volume of speaker.
►Increases values of user menu in main OSD menu.
►Executes function (by OSD help commands) in main OSD menu.
MENU
►Activates main OSD menu.
►Navigates higher menu in main OSD menu.
►Exits OSD menu.
FUNCTION 1
►Executes functions of user selected
UNDEF, Marker Size, Audio LV Meter, Wf/Vector, H/V delay. Aspect, Audio Loudness(LKFS),
Mono/Blue only, Audio Channel, Safety marker size, Time code, Caption, Audio mute, Still
image, Zoom, Flip, Gamma select, Vector Color, Fan Control, I/P Mode, Marker Preset1,
Marker Preset2, WFM Line Select, PIP func & Input, Sub win full, Sub win part
FUNCTION 2
FUNCTION 3
FUNCTION 4
FUNCTION 5
FUNCTION 6
MARKER
►Draw Marker on Screen ( Off -> 16:9 -> 4:3 … -> 2.35:1 )
SCAN
►Executes Scan function ( Over-Scan -> Zero-Scan -> Under Scan-> Pixel to Pixel)
SDI 1
►Select SDI 1 source directly
SDI 2
►Select SDI 2 source directly
ANALOG
►Select ANALOG source directly
( ‘Composite1’ ->‘Composite2’ ->‘Composite3’ -> ‘S-video’ -> ’.B.R’ -> ‘Y.Pb.Pr’ -> ’PC’ ->
‘HDMI’ -> ‘DVI’)
Adjust
►Adjust Picture Menu(Brightness -> Contrast -> Color -> Sharpness->Phase & Tint)
►Turn Right (with ‘UP' button is same)
►Turn Left (with ‘DOWN' button is same)
Front panel LED Operations
- Green Led turned on during execution of key Function and Power On
- Stan-by mode is LED Red

USO RESTRITO
[User’s Manual] Page 12
Speaker Out
Interface
Description
Speaker R out
8 ohm±15%, Max 2W + 2W
Speaker L out
2. Rear Panel
Connection Details
AC
IN
SDI 1
OUT
IN
SDI 2
OUT
RS-232C IN
RS-232C OUT
HDMI
DVI-I
CVBS1
/Pr/R
CVBS2
/Y/G
CVBS3
/Pb/B
AUDIO
IN
IN
OUT
IN
IN
OUT
OUT
R
L
AUDIO
OUT
R
L

USO RESTRITO
[User’s Manual] Page 13
DC Battery IN (PRM-22424V)
PIN NO
Description
1
GND
2 , 3
4
+ 12V/24V
RJ-45
- Firmware Upgrade & GPI
Remote PIN Assignment
1 PIN
COMMON(GND)
5 PIN
GPI 4 PORT
2 PIN
GPI 7 PORT
(STAND BY/POWER ON/OFF)
6 PIN
GPI 3 PORT
3 PIN
GPI 6 PORT
7 PIN
GPI 2 PORT
4 PIN
GPI 5 PORT
8 PIN
GPI 1 PORT
1
2
3
4
DC IN
Ethernet
to Serial
GPI
Control Terminal: 1 ~ 7 Pin
Contact Point Switch
It is possible to attach
pin one by one.
GND Terminal: 8 Pin of RJ-45

USO RESTRITO
[User’s Manual] Page 14
Interface description
Interface
Description
SDI 1 IN
HD SDI / SD SDI Input
SDI 2 IN
SDI 1 OUT
SDI 1, SDI 2 Loop Out
SDI 2 OUT
RS-232 IN
Update/Multi Control/Auto color calibration
RS-232 OUT
Multi Control out
HDMI
High Definition Multimedia Input
DVI-I
DVI-I Type Digital / Analog PC-RGB Video Input
High Definition Multimedia Input Compatible
CVBS1/Pr/R In
GBR (SOG sync) Input
Y, Pb, Pr Component Video Input
CVBS / Composite/S-Video Input
CVBS2/Y/G/Y In
CVBS3/Pb/B/C In
CVBS1/Pr/R Out
Component/GBR/Composite1,2,3/ S-Video Loop Out
CVBS2/Y/G/Y Out
CVBS3/Pb/B/C Out
AUDIO R In
DVI-I/Component/GBR/Composite1,2,3/S-Video Sound Input
AUDIO L In
AUDIO R Out
AUDIO MONITOR OUT
AUDIO L Out
AC IN
AC90V ~ 240V, 50Hz/60Hz
DC IN
PRM-217: DC 11V ~ 17V ,PRM-224: DC 24V
UPDATE
Firmware Upgrade
GPI
GPI 1 ~ 7 Control Port
4. MENU OVERVIEW
In this system menu, there are several ways to customize the menu settings provided.
Most menus consist of three levels to select the option, but some require greater depth for the variety of
settings. If you press the MENU button, only the first and second level of the menu system will appear on
the monitor screen. The third level can be displayed by pressing SEL/INPUT. If a menu has more than
three levels, the pop-up dialogue box will be displayed as the fourth or fifth level.
1. To show and remove the Menu
Press the MENU button to display the menu. Press the MENU button again will take you back to monitor
viewing.
2. To go to the next level
Press SEL/INPUT button.

USO RESTRITO
[User’s Manual] Page 15
3. To go back to the previous level
Press MENU button
4. Typical Menu Operation
1. Press MENU button: The main menu will appear.
2. Use UP/DOWN button to select the desired menu option (icon).
3. While the desired menu option is selected, press SEL/INPUT to move to the second level.
4. Use UP/DOWN button to select the second menu option.
5. Press SEL/INPUT to move to the third level: Some menu options require additional steps.
6. Press MENU to return to the previous menu to return to monitor viewing.
5. BASIC OPERATION
1. Turning On the Monitor
1. First, connect power cord correctly. At this moment, the monitor switches to standby or power on
mode. In standby mode, in order to turn monitor on, press and hold down the ST-BY button for 3 sec.
2. Select the viewing source by using SEL/INPUT button on Keypad in front of monitor
2. Volume Adjustment
1. Press the UP/DOWN button on Keypad.
2. If you want to switch the sound off, press the FUNCTION (Audio mute) button.
3. You can cancel this function by pressing the FUNCTION (Audio mute) or volume control button.
3. On Screen Menus Language Selection
- SETUP -> On Screen Display -> OSD Option -> Language
- The menus can be shown on the screen in the selected language.
- Supported Language: English, Spanish, Portuguese, German, French,
Italian, Hindi

USO RESTRITO
[User’s Manual] Page 16
6. On Screen Menus Selection and Adjustment
1. How to adjust the OSD screen
1. Press the MENU button and then UP/DOWN button to select each menu.
2. Press the SEL/INPUT button and then use UP/DOWN (SEL/INPUT)/MENU button to display the
available menus.
• Your monitor's OSD (On Screen Display) may differ slightly from what is shown in this manual.

USO RESTRITO
[User’s Manual] Page 17
7. SELECT VIDEO INPUT
1. How to Select Video Source by OSD
1. Press the SET/INPUT button and then UP/DOWN button to select each video source.
2. Press the SET/INPUT button to go to desired video source.
3. If Input Name is enabled, The SET/INPUT button goes into input name edit mode instead of selecting
source.

USO RESTRITO
[User’s Manual] Page 18
8. PICTURE MENU OPTIONS
1. Video Menus of each Input modes
< Video (NTSC) Picture menu> < PC Picture menu> < SDI, HDMI Picture menu>
2. Adjust
- Adjust the values of Brightness, Contrast, Color, Tint and
Sharpness directly from -50 to 50
Contrast, Brightness, Sharpness, Color (All Sources), Tint (without
PC, DVI, HDMI, Component), Phase (Component).
3. Color Temperature Control
- For Setting the Color temperature or adjusting RGB gain value directly
- User (User setting RGB gain value), VAR(3200K ~ 11000K), Often used value(11000K, 9300K, 6500K,
5400K,3200K) and 3D LUT Calibration value(D65 – 6504K/C-6774K/D-Cinema 6302K)

USO RESTRITO
[User’s Manual] Page 19
4. SCAN
1. Over Scan – 95% input size and fit the selected display size
2. Zero Scan – 100% Input size and fit the selected display size
3. Under Scan – 105% Input size and fit the selected display size
3. Pixel to Pixel – Display size is an input size. If input resolution is
bigger than panel size, fit the panel size
5. Aspect Ratio
- For setting the aspect ratio.
- Full Screen: The images are displayed with a panel size.
- Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1: The images are displayed with each aspect ratio.
- Funtion-key operate Rotation, Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1
- AFD function Added
- PC mode: Full Screen & 4:3 only
6. Zoom
- Can see the enlarged picture by (2X, 3X, 4X, 5X) ratios.
- If user select the Zoom 2X, can see the below yellow box in
picture.
- Press Select or Enter button, user can see the enlarged picture.
- Menu key escape the zoom mode.

USO RESTRITO
[User’s Manual] Page 20
- Example (3X3)
Zoom X position: Coordinate of video image’s column position.
Zoom Y position: Coordinate of video image’s row position.
7. Mono/Blue Only
- Mono color: For selecting monochrome images.
- Blue Only: Images have only blue color expect red and green
color
8. PC Menu (pc mode only)
- Only operate PC input mode
- Select Auto-adjust and adjust Phase, HV position, Frequency
- Auto-Adjust automatically set the optimum values of Phase, HV position and Frequency.