Polaris 2883419 User manual

APPLICATION
Verify accessory fitment at Polaris.com.
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
KIT CONTENTS
This Kit includes:
NOTE
Kit PN 2883419 shown; Kit PN 2883840 similar.
REF QTY PART DESCRIPTION PART NUMBER
1 1 Vehicle Cover -
1 Instructions 9928598
TOOLS REQUIRED
• Safety Glasses
IMPORTANT
Your Trailerable Cover Kit is exclusively designed for your vehicle. Please read the installation instructions
thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to
ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.
Instr 9928598 Rev 03 2018-04 Page 1 of 4
P/N 2883419, 2883840
TRAILERABLE COVER KIT

Instr 9928598 Rev 03 2018-04 Page 2 of 4
ASSEMBLY TIME
Approximately 5 minutes
INSTALLATION INSTRUCTIONS
1. Shift vehicle transmission into “PARK”. Turn
ignition switch to “OFF” position and remove key.
2. Before cover installation:
• Examine vehicle for any accessories that extend
outside of ROPS or vehicle body to ensure
proper fit of cover and prevent damage. Remove
or stow accessories and/or install padding as
necessary.
• Ensure exterior of vehicle is clean. Transporting
a dirty vehicle with cover installed may damage
vehicle finish.
• If not already done, temporarily stow ratchet A
at left rear corner of cover by folding over and
securing flaps with hook and loop strips.
3. Carefully drape cover qover vehicle, pulling
cover as far down over tires as possible.
IMPORTANT
Cover MUST be pulled down below lower surface of
tires, and straps located BELOW lower tire lugs, to
ensure cover stays in place during transport.
NOTE
Exterior of cover has “FRONT” label; ratchet is
located at left rear corner.
RANGER®cover shown; RANGER CREW®similar.
4. Secure front of cover by connecting buckles B.
NOTE
LH strap is sewn to edge of cover opening; RH strap
is free to slide in cover pocket. Cover opening
accommodates accessory winch or plow installation
(sold separately).

Instr 9928598 Rev 03 2018-04 Page 3 of 4
5. Secure rear of cover.
a. Partially close ratchet A.
b. Thread RH strap through loop on end of center
strap.
c. Pull RH strap tight, then fold strap and insert
into ratchet Aspool.
d. Operate ratchet mechanism until slack is
removed, then EXAMINE ALL FOUR TIRES to
ensure strap is positioned BELOW lower tire
lugs as shown. Adjust as necessary.
e. Tension strap sufficiently to prevent it from
slipping above tire lugs during transport, then
fully close ratchet lever A.

Instr 9928598 Rev 03 2018-04 Page 4 of 4
6. Secure middle of cover by connecting male
buckles Don each end of center strap to female
buckles Csewn into cover. Tighten strap as
required, then confirm strap is not in contact with
sharp vehicle structure.
NOTE
RANGER CREW®cover has two center straps,
center front and center rear.
7. Ensure fuel filler zipper is fully closed.
8. If buffeting occurs during transport then remove or
adjust cover.
9. When removing cover, stow ratchet as described
in Step 2 above.
WARNING
If transporting vehicle in non-enclosed trailer then
vehicle must FACE FORWARD, or cover must be
removed.
Failure to comply may allow airflow, vibration, or
other factors to separate cover from vehicle and
cause an accident, resulting in serious personal
injury or death.
FEEDBACK FORM
A feedback form has been created for the installer to provide any comments, questions
or concerns about the installation instructions. The form is viewable on mobile devices
by scanning the QR code or by clicking HERE if viewing on a PC.
FEEDBACK FORM