Potensic ATOM SE User manual

User Manual
DANGER
Only suitable
for age 14+
Email: [email protected]
Email: [email protected]
Email: [email protected]
Email: [email protected]
Email: [email protected]
Email: [email protected]
Email: [email protected]
Web: www.potensic.com
FB: www.facebook.com/Potensic
SE
ATOM

01. Please properly keep the package and manual which contain important information.
02. User should avoid personal and property losses when using the product.
03. Neither the Company nor our dealers bear any liability for the proper losses and personal injuries due to users.
04. Debug and install the product in strict accordance with the Manual’s steps. Keep a distance over 1~2m with others while
using the product, to avoid injury when the product crashes into people’s head, face and body.
05. The product should be assembled by an adult. Users aged below 14 should not handle the product alone. The battery
should be charged under the supervision of an adult and by avoiding inflammables.
06. Keep the product out of children’s reach to avoid eating it by mistake, for it contains small parts.
07. Do not use the product on the road or water to avoid an accident.
08. It is forbidden to dismantle or refit the product, except for the propellers; otherwise, an anomaly may occur.
09. Please recharge the intelligent battery with USB charger that conforms to FCC/CE standard.
10. The remote controller has a built-in 3.7V lithium battery which needs no replacement.
11. Do not short circuit or squeeze the battery to avoid explosion.
12. Do not short circuit, break down or throw battery in fire or place it in hot place (in fire or near electric heater).
13. Keep a safe distance to the propellers which are revolving at a high speed; do not use the product in the crowds to avoid
scratch or injury.
14. Do not use the product in places with strong magnetic field, such as near high-voltage cable, buildings which contain
metals, automobiles and trains; otherwise, the product can be disturbed.
15. Please do master local laws and regulations, to avoid violation of regulations.
16. Stop using the remote control within the radio control period and region of national departments as specified, in order to
conform to the requirements for magnetic environment of aeradio.
17. Avoid low-altitude flight above water surface.
18. Keep it away from airport, airline and other no-fly zone.
01
1. Disclaimer & Precautions
1.1 Disclaimer
Please follow the Manual’s operation instructions and precautions strictly, in order to use the product safely and correctly.
Users aged under 14 must be accompanied by an adult while using the product. Please keep the product out of children’s
reach.
For any direct or indirect loss (including but not limited to property loss and personal injury) due to user’s failure in
following the Manual’s safety operation, the Company does not bear any liability or offer warranty services.
Do not dismantle any part except for propeller blades, or refit the product and attach other items on it; otherwise, user
should undertake the consequences arising therefrom.
For any problem in use, handling and maintenance, please feel free to contact our local dealer or the Company.
1.2 Safety Precautions
Keep away from obstacles and crowds
Keep the product away from crowds, high-rise buildings and high-voltage cables, and avoid using it in severe weather such
as wind, rain and thunder, in order to keep safety of user and the crowds, for the product may have uncertain flying speed,
status and potential hazards.
Keep off moisture
Keep the product off moisture to avoid an anomaly or damage due to humidity of precise electronic components and
mechanical parts inside it.
Safe operation
The product may be exposed to higher risk when user feels tired or lacks of energy and experience. Please refit or repair the
product with the original parts to keep safety. Please operate and use the product within the allowed range and make sure to
follow the local safety rules.
Keep away from high-speed revolving parts
While the product’s propellers are revolving at a high speed, keep it away from the crowds and animals to avoid scratch or
disturbance. Do not touch the revolving propellers with hands.
Keep away from heat source
Keep the product away from heat and high-temperature exposure to avoid the anomaly, deformation and even damage, for
it is made of metal, fiber, plastic and electronic elements.
1.3 Warning & Prompts
EN

02
2. Reading Tips
2.1 Symbols
Prohibited Important Operation & use prompts Vocabulary explanation and reference information
2.2 Suggestions of Use
1. User is highly suggested to watch the teaching video and Quick Operation Guide before
consulting the Manual.
2. Make sure to read Disclaimer & Precautions first when consulting the Manual.
2.3 Teaching Video / PotensicPro APP
Scan the QR Code at the right side to view Potensic Atom SE (Atom SE)
teaching video and download PotensicPro APP (APP)
Please do watch the teaching video in order to use the product correctly
and safely.
User can also view the teaching video of Atom SE in the menu column of
APP homepage.
2.4 Registration & Help
Make sure to register personal account in APP before the first flight, in order to get better use experience.
Steps of Registration
Please fill your E-mail, password, check the protocol and click “Register”. You can login the system
after registration.
(Note: Keep the mobile phone online during registration)
Help
Thanks for purchasing Atom SE drone. Please read the Manual carefully.
Please contact our support team ([email protected]), and show us your product order number
of Amazon or official website, if any help is needed.
2.5 Vocabulary Explanation
IMU (inertial measurement unit), the most important core sensor of the drone.
TOF (time of flight), the period from transmission and receiving of detection infrared signal, in order
to determine the target distance.
The sensor system, which lies at the bottom of the drone and consists of camera and TOF module.
High-accuracy positioning, which is realized through lower visual system.
Identify direction for geomagnetic sensor and the drone.
Atmospheric pressure sensor, which enables the drone to determine the altitude through atmospheric pressure.
Switch the drone motor from static status to idle running.
Once unlocked, the motor will start revolving at a fixed speed, but it has insufficient lifting force to take off.
The drone will return to HOME point automatically based on GPS positioning.
Electronic stabilization; the camera will detect the data of high-frequency vibration and eliminate
picture flutter through algorithm.
Position of the drone camera.
Ascend or descend the drone.
Fly the drone to front or back.
Fly the drone to left or right.
Enable self-rotation of the drone to left or right.
IMU
TOF (Time of Flight)
Lower visual system
Visual orientation
Compass
Barometer
Lock/unlock
Idling
Auto return
EIS
Drone head
Throttle control stick
Pitch control stick
Roll control stick
Yaw control stick

03
Please check if your package contains the following items before using the product:
Picture Description Single Battery
Version
Fly Expansion
Kit
Drone
(including propeller
blades and camera)
Smart battery
Remote control
Spare propellers
Screw driver of
propeller blades
Data cable
(for charging the battery
and the remote control)
Adapter cable of the
remote control
Specific screws of
propeller blades
Parallel Charging
HUB
Parallel Charging HUB
Specific adapter
Portable handbag
User’s manual
Parallel Charging HUB
User’s manual
1 1 /
1 1 /
/ / 1
/ / 1
/ 1 1
1 1 /
/ / 1
8 8 8
1 1 /
3 3 /
1 1 /
1 2 2
8 8 8
2.6 Packing List
Double Battery
Version
EN

04
Contents
01 Disclaimer & Precautions
Disclaimer
Safety & Precautions
Warning & Prompts
02 Reading Tips
Symbols
Suggestions of Use
Teaching Video/Download APP
Registration & Help
Vocabulary Explanation
Packing List
04 Contents
05 Overview
Introduction
Name of the Drone Parts
Name of the the Remote Control
Preparation of the Drone
Preparation of the Remote Control
Charging/Startup and Shutdown
09 Drone
Positioning
Lower Visual System
Drone Status Indicator
Smart Battery
Propeller
Flight Data
Steering Engine Camera
14 Remote Control
Overview
Control Stick Mode
Function Introduction
Antenna Angle
18 PotensicPro APP
APP Homepage
Flight Interface
21 Flight
Requirements of Flight Environment
Flight Precautions
Connection
Flight Level
Compass Calibration
Beginner Mode
Takeoff/Landing/Hovering
Smart Flight
Auto Return
Emergency Stop
26 Appendix
Specification & Parameters
Authentication Introduction

Overview
This chapter introduces the functional characteristics of Atom SE, as well as the component name of the
drone and the remote control.
With foldable arms and a weight below 250g, the product is portable, which can also be used without
real-name registration in most countries. The product is fitted with a visual positioning system, to realize
precise hovering at low altitude indoor and outdoor environment. Meanwhile, the product is fitted with a GPS
sensor to realize positioning and auto return. Based on 1/3 " Sony CMOS image sensor, the product can shoot
4K/30FPS HD video and 1.2-megapixel pictures.
By using the brand new PixSync 2.0 2.4G digital image transmission technique, the Atom SE remote control
can realize 4 km communication distance and 720P HD image transmission maximally at ideal conditions.
Open the pull-type and the foldable remote control to contain your mobile device. Connect the remote control
and mobile device with USB data cable, to operate and set the product through APP and display HD image
transmission picture. The built-in lithium battery of the remote control can work for approx. 2h maximally.
The max. horizontal travelling speed of Atom SE can reach 16m/s and the max. flight period is approx. 31min;
it can resist the Scale 5 wind.
3.1 Introduction
Test method of the max. flight period: Fly at an even speed of 5m/s at 25°C and breezeless condition.
Test method of the max. distance: Measured at an open and no-interference environment, with a flight height of 120m, and
without considering the return of the drone.
Necessary tools for one flight:
1. Drone 2. Fully-charged smart battery 3. Remote control 4. Smart phone 5. Adaptive datacable of mobile phone
3.2 Name of the Drone Parts
1. Charging indicator
2. TYPE-C charging port
3. Battery buckle
4. SD card slot
5. Tail indicator
6. Monocular visual module
7. TOF module
8. Bottom cooling hole
9. Power indicator
10. Power/frequency pairing button
11. Integrated camera of steering engine
12. Brushless motor
13. Propeller
14. Arm
15. Antenna tripod
16. Arm shaft
05
4
9
1
5
7
12
13
14
15
16
8
10
11
2
3
6
EN

06
1. Power button
Long press it for 2s to power on/off.
2. Power indicator
Indicate the electric quantity or other status
of the remote control
3. Control stick slot
One slot respectively at the left and right side,
which are used to contain control stick.
4. TYPE-C interface
To charge the remote control/connect
mobile device
5. Return / Pause button
Long press for 1s to return to HOME point
automatically
Short press it to pause auto flight
6. Control stick
7. Foldable double antennas
8. Installation position of mobile device
To place mobile device.
9. Shoot button
Short press it to shoot one picture
10. Record button
Short press it to start/stop recording
11. Left thumbwheel
Dial the left/right thumbwheel to adjust
the pitch shooting angle of camera
3.3 Name of the the Remote Control
9
11
10
4
8
6
7
5
2
3
1

1. Open the antenna.
2. Insert the mobile phone to the bent side
of USB cable.
3. Push the data cable side of mobile
phone into the card slot of the remote
control.
4. Pull and open the remote control with
both hands, fix both ends of mobile
phone stably.
5. Insert the other end of data cable to the
remote control.
6. Remove control stick.
7. Screw in control stick screw hole
clockwise
8. Installation completed.
07
3.4 Preparation of the Drone
The product is delivered under folded status. Please unfold it as follows:
1. Remove the propeller belt.
User is suggested to fold the arms and fix the propeller blades with belt when carrying the product.
3.5 Preparation of the Remote Control
Installation of mobile phone and control stick
2. Unfold the front arm before the rear arm, and unfold the propeller blades.
1
2
3
5
4
6
7
8
EN

08
3.6 Charging / Startup and Shutdown
Startup
Drone: Make sure the battery is inserted in battery bin, short press and then long press the power button
until all indicators are on, and then release the button to start up.
Remote control: Long press the “Power” button until all indicators are on, and then release the button to
finish startup.
Shutdown
Drone: Short press and then long press the power button of the drone until all indicators are on, and then
release the button to shut down.
Remote control: Long press the power button until all indicators are off, and then release the button to
shut down.
The shortest charging period is approx. 1h 25min through TYPE-C charging port. Make sure your charger supports 5V/3A
output in order to realize this charging speed.
User is suggested to charge battery through Parallel Charging HUB, in order to charge 3 batteries quickly at the same time.
It is suggested to take out battery for charging for the sake of safety; otherwise, the product fails to be started if the
battery is inside the product when being charged.
When the charging wire is inserted while the product is powered on, the product will shut down automatically and
then continue with charging.
The battery may become too hot after use; do not charge it until it cools down; otherwise, charging can be rejected by
smart battery. Recharge the battery on a trimonthly basis, to guarantee the activity of cell.
Please connect the original data cable or the cable that supports over 3A current to the TYPE-C interface; otherwise, it
may have charging failure or battery damage.
Wake up battery prior to the first flight; Otherwise, it cannot be started. Connect the TYPE-C charging
port of battery and USB charger to the AC power supply to finish one-time charging (USB charger is not
included in the product. User can use the charger that conforms to FCC/CE specification to charge the
product).
The red indicator will be on during charging, and turn off automatically after charging is done.
User can recharge the battery with Parallel Charging HUB if fly expansion kit is purchased. For details,
please refer to User’s Manual of Parallel Charging HUB. Meanwhile, the Parallel Charging HUB can
also recharge the remote control.
Mode 2
Mode 1

09
4. Drone
The product consists of a flight control system, a communication system, a positioning system,
a power system and a smart flight battery. This chapter sets down the functions of all parts of
the drone.
4.1 Positioning
The new generation flight control of Potensic is adopted in Atom SE. The following two positioning modes below
are supported by this flight control:
GPS positioning: Realize precise positioning through GPS module; support precise hovering, smart flight and
auto return.
Visual positioning: It can realize high-precision positioning at a low altitude based on the lower visual system.
The visual positioning can be realized without GPS signal, so that the product can be used indoors.
How to switch: The flight control system will switch automatically according to the environment of the drone. If
both GPS and lower visual system fail, the flight control will be switched to attitude mode, under which, the drone
fails to realize stable hovering and user needs to correct the flight gesture manually through the control stick.
The difficulty of drone handling will be increased greatly in the attitude mode; make sure to master the behaviors
and operation of the drone in this mode before using this mode; avoid flying the drone at a long distance, to avoid
risks due to failed judgment of drone gesture.
In visual positioning, smart flight is not supported and flight speed will be restricted.
Make sure to master the operation characteristics of the drone in this mode, for the difficulty of drone handling
will be increased greatly in attitude mode. Always keep the drone within sight in order to avoid hazards due to
failed judgment of drone gesture and direction.
4.2 Lower Visual System
Atom SE is fitted with a lower visual system that is installed at bottom of the
drone and consists of monocular camera and TOF module. Furthermore,
the TOF module is divided into transmission tube and receiving tube, to
calculate the height of the drone relative to ground accurately by measuring
the period from transmission to receiving of infrared signals. With the help
of monocular camera, it can calculate low-altitude accurate position of the
drone and then realize high-precision positioning.
Observation range
The working altitude range of lower visual system: Available at 0.3-30m, realize precise positioning at 0.3-5m.
Application scenario
The visual positioning function realized by the lower visual system applies to the scenario which has no GPS
signal or poor GPS signal, rich surface texture, enough light condition and the relative height of the drone is
0.3-5m. When this range is exceeded, please use the product with caution for the positioning accuracy can be
reduced.
Use method
It will be enabled automatically when visual positioning conditions are satisfied. In visual positioning mode, the
tail indicator of the drone will flicker slowly in cyan.
Speed limit: The flight speed will be restricted at 1m/s when visual positioning and flight is entered, in order to
ensure positioning accuracy and flight safety.
Visual positioning is an auxiliary flight function only. Please pay attention to the changes of flight environment and
positioning mode, instead of excessively relying on self-judgment of the drone. User needs to handle the remote control in
the full process, and always gets ready for manually operating the drone.
Visual positioning may fail in the following surface texture
1. Pure-color surface
2. Surface with strong reflection, such as smooth metal surface
3. Transparent object surface, such as water surface and glass
User can also switch to attitude mode in APP.
TOF Module
Monocular Camera
EN

10
4.3 Drone Status Indicator
Startup / Shutdown in progress: Green indicator is normally on
Flight status
GPS positioning Visual positioning Attitude mode Return
Indicator flickers
slowly in green
Indicator flickers
slowly in cyan
Indicator flickers
slowly in blue
Indicator flickers
slowly in red
Warning & Error
Remote control has no
connection with the drone
(communication lost)
Low battery Sensor error Emergency stop of propeller
Indicator is normally
on in blue
Indicator flickers
quickly in red
Indicator is
normally on in red
Indicator has long-extinguishing
and short-illuminance
Upgrade &
calibration
Compass calibration
(horizontal)
Compass calibration
(vertical)
Frequency
pairing mode Upgrade mode
Indicator has alternative
flickering between red
and green
Indicator has alternative
flickering between blue
and green
Indicator flickers
quickly in green
Indicator flickers
quickly in blue
4.4 Smart Battery
4.4.1 Function Introduction
Atom SE smart battery is mounted with high-energy cell and advanced BMS. The details are as follows:
Basic Parameters
Cell Qty.
Rated Voltage
Charging Mode
2 series
7.2V
TYPE-C/Parallel Charging HUB
Battery Capacity
Charge Completion Voltage
Max. Charge Current TYPE-C: 5V/3A
Parallel Charging HUB: 8V/2.2A x 3
2500mAh
8.4V
Function Introduction
Balance protection
Self-discharge
protection
Overcharge protection
Temperature
protection
Intelligent current
limiting of charging
Overdischarge
protection
Short-circuit
protection
Battery health
monitoring
Communication
function
Balance cell voltage automatically to guarantee battery health.
Fully charged battery can be used for 5 days; if there’s no operation in this period, the battery will be
discharged slowly to around 70%, in order to protect the cell.
Charging will stop once battery is fully charged, for the battery can be damaged by overcharge.
Please pay attention to your charging environment, for charging will be stopped automatically when battery
temperature is below 0°C or above 50°C.
When charging current is too high, the battery will restrict current automatically in order to protect the battery.
In non-flight status, the battery will cut off power supply automatically to avoid over-discharge when battery is
discharged to a certain level; at this time, the battery will enter sleep status. It is suggested to charge the battery ASAP.
When the drone short-circuit is detected by the battery, the power supply will be cut off automatically to
protect the battery and the drone.
The BMS will monitor the battery health condition, prompt battery damage in APP in case of cell damage, cell voltage
unbalance or other battery errors, to remind user to replace the battery in time.
The battery can communicate with the the drone in real time. User can view the information in APP, such as battery
circulation times and real-time electric quantity.
Read and follow the Manual’s disclaimer and requirements on battery sticker before using the smart battery; otherwise, user
should undertake the consequences arising therefrom.
Start-up/Shut-down
4. The moving texture, such as running pets and moving vehicles.
5. Scenarios with drastic change of light; For example, the drone flies to outdoor space with strong light from indoor space.
6. Places with weak or strong light.
7. The surface with highly repetitive texture, such as floor tile with the same texture and small size, and highly consistent
strip pattern.
For the sake of safety, please check the camera and TOF receiving tube prior to fight to remove dirt. Please feel
free to contact the after-sales department for repairing if there’s damage.
Model: DSBT02A

11
4.4.2 Battery Installation & Removal
Installation:
Push the battery into the product’s battery bin
horizontally as shown in picture below, the battery
buckle is bounced and locked when hearing “click”
sound.
Buckle is not in position, which
may make battery fall during flight
Make sure to power off the product
before removing the battery.
4.4.3 Charging
See 3.6 for charging method
4.4.4 View Electric Quantity
Once the battery is inserted in the drone, short press the power button to view the electric
quantity of smart battery, as shown in the picture below:
0%~25%
25%~30%
30%~50%
50%~55%
97%~100%
80%~97%
75%~80%
55%~75%
LED 1 LED 2 LED 3 LED 4 Current electric quantity
Indicator is flickering Indicator is off
Indicator is normally on
The discharge capacity will be weakened greatly and flight duration will reduce at a low temperature, which is normal.
Avoid long-term running at a low temperature, otherwise, the battery life can be shortened.
Once the battery is inserted, make sure the battery buckle is bounced properly. This step is highly important and
related to flight safety.
Power Button
LED 1
LED 2
LED 3
LED 4
Buckle is in position, safe
Removal:
Firstly, press the buckle of smart battery, hold
the upper cover of battery to pull out the battery.
4.4.5 Operation Instructions of Smart Battery at High/low Temperature
When battery temperature is <10°C, the APP will prompt battery low temperature and the battery needs
preheat before use.
When battery temperature is >53°C, the APP will prompt battery high temperature and the drone may fail to
take off.
EN

12
4.5 Propellers
The propellers of Atom SE are divided into forward and reverse propellers. The marked propeller blades are
forward propeller blades, rotate clockwise and corresponding arms have the same marks; the unmarked
propellers are reverse propellers, rotate anticlockwise and the corresponding arms have no mark.
Propeller
Marked
propeller
Install the marked propeller
blades on marked arm
Unmarked
propeller
Install the unmarked propeller
blades on unmarked arm
Installation Instructions Schematic Diagram of
Installation
The components include specific screwdriver, spare propeller
blades and screws.
Hold the motor to remove the propeller blades easily.
Make sure to replace propeller blades with the original screws and fasten screws.
While installing the propeller blades, make sure the side with characteristic faces upwards; otherwise, the product may
fail to take off.
For any damage of propeller blades, it is recommended to replace all propeller blades and screws on this motor. The
new propeller blades installed must be from the same pack.
While removing and using the propeller blades, avoid scratch and deformation due to squeezing of hard objects, for the
propeller edge is thin.
The propellers are quick-wear parts, which should be purchased separately.
Keep off the revolving propellers to avoid injury.
For any jitter, reduced speed and duration in flight, please inspect the propeller blades in time, or timely replace the
propellers which are damaged or deformed.
Make sure the motor has no foreign matters, can rotate freely and be free from noise. For any anomaly of motor, do not
unlock it, but contact the after-sales department for troubleshooting. Make sure to inspect the propeller blades and
motor and timely replace the damaged propeller blades prior to flight.
While removing propeller blades, do not insert the screwdriver or other
sharp objects into the ventilation holes of motor; otherwise, the power
motor can be damaged severely.
4.6 Flight Data
Atom SE supports recording of flight data. User can view the data in APP.
“Flight record” can display the basic data for each flight of user.
“Flight log” can record the detailed flight data of user. For any anomaly in flight, user can report it in APP
and, if necessary, upload the flight log to seek for assistance.
All flight data are stored in user’s mobile device. No flight data will be acquired by the Company, except for the data
uploaded by user to the cloud platform.

13
4.7 Steering Engine Camera
4.7.1 Steering Engine
The Atom SE camera is mounted with a steering engine platform,
to adjust pitch angle freely from +20° to -90° (horizontal direction
is 0°).
The angle of steering engine can be adjusted by dialing the left
thumbwheel of the remote control.
The steering engine will be recovered to -9° automatically after each startup.
Avoid collision and moving the lens by force, for the steering engine contains precise parts.
Make sure the steering engine has no foreign matters and lens is free from dirt before takeoff.
The steering engine is connected to the drone through elastic and shock absorption support, to eliminate camera
vibration. Do not pull the steering engine by force. For any damage of shock absorption support, please timely
contact the after-sales department for repairing.
Do not bind or paste any object on the steering engine. Otherwise, it may damage the drone.
4.7.2 Camera
Sensor brand: SONY
Effective pixel: 1300W
FOV: 118°
ISO range: 100~6400
Memory: Micro SD card
Sensor size: 1/3"
Aperture: F2.2
Focus range: 3m ~∞
Shutter range: 1/30~1/25,000s
Shooting distortion: < 1% (after calibration)
Picture size: 12M (4,608*2,592)
Video specification: 4K30 2.7K30 1080P60 1080P30
Video format: MP4
Picture format: JPG/JPG+RAW(DNG)
Code: H.264
Basic Parameters
Shooting Ability
Do not touch the lens that will become hot after long-term recording to avoid scald.
Do not record video when the product has no flight; otherwise, the drone can enter overheat protection.
In 1080P60 format, the image mode is middle cutting, FOV is approx. 66°.
4.7.3 Image Storage
The videos and pictures recorded by Atom SE will be stored in SD card, instead of APP or user’s album. Make
sure to insert SD card prior to flight. Otherwise, it is unable to record and shoot. (SD card is not included in the
product’s pack list!)
User can preview and download the videos and pictures (the drone and the remote control should be
connected) in APP.
Introduction to SD Card
File format: FAT32
Capacity: 4G-256G
Speed requirements: It is suggested to use SD card above U1 (UHS Speed Class 1) or C10 (Class 10)
The video downloaded from APP is just 720P image used in image transmission. Please read SD card with computer or
other device in order to acquire videos of higher definition.
The recording can be terminated due to slow write-in when using the U1/C10 SD cards of certain brands.
The product does not support exFAT files. When SD card formatted exFAT is inserted by user, the APP will prompt formatting;
otherwise, the product cannot be used.
If important data are stored in your card, please backup them properly to keep safety.
Do not insert or unplug the SD card when the product is powered on. It may lead to data damage or loss, or even SD card
damage when inserting or unplugging SD card during video recording.
Potensic does not bear responsibility for any loss due to user’s misoperation of SD card.
0°
20°
-90°
EN

14
5. Remote Control
5.1 Overview
DSRC02A remote control is designed exclusively by Potensic for Atom SE based on PixSync 2.0 image
transmission technique. It can realize operation and setting of the drone within the max. straight-line
distance of 4 km at a flight height of 120m in unblocked environment; besides, it can display the real-time
shooting HD image of the drone on the mobile device through the APP.
Based on 2.4G band double high-gain antenna, PixSync 2.0 can ensure smooth transmission of 720P HD
pictures in undisturbed and unblocked environment.
With built-in 2,200mAh polymer battery, the remote control can work for approx. 2h maximally. The remote
control has one TYPE-C interface for charging and connecting the mobile device; besides, it can recharge
the mobile device (5V/500mA).
5.2 Control Stick Mode
Mode 1 (Left Hand Throttle)
Left control stick Right control stick
Left Right
Ascend
Descend
Left
rotation
Right
rotation
Front
Back
Left Right
Ascend
Descend
Front
Back
Left
rotation
Right
rotation
Mode 2 (Right Hand Throttle)
Left control stick Right control stick

15
5.3 Function Introduction
5.3.1 Function List
1. Connect TYPE-C charging port to USB charger.
2. The battery is being charged when power indicator starts flickering.
3. Charging is completed when 4 LED indicators are on and data cable can be removed.
Charge
Recharge mobile
phone
When a mobile device is connected, it will be recharged automatically by the remote
control (5V/500mA)
Indicator function See 5.3.2
Flight control See 5.2
One-key return See 7.9
Emergency stop
For any accident in the flight, press “Shoot” and “Record” button for 2s at the same time
and when there’s “beep” sound, the product will stop immediately and fall on the ground
freely.
Shoot
Short press it to shoot one picture
When camera is in video recording mode, short press it to switch to
shoot mode
Record video
Short press it to start/stop video recording
When camera is in shooting mode, shot press it to switch to video
recording mode
Camera pitch
control
Dial it to the right to increase the pitch angle (head up)
Dial it to the left to decrease the pitch angle (head down)
Remote control
frequency pairing See 5.3.3
Low battery
prompt
When electric quantity of the remote control is lower than 10%, the remote control will
have long “beep” sound at an interval of 1s.
Auto shutdown The product will shut down automatically if the remote control has no connection and
operation for 20min.
Pause
When the drone is under auto flight (such as auto return and circle flight), short press
return/pause button to pause the current light, then the drone will hover at the current
position; then short press it again to continue with flight.
EN

16
0%~25%
99%~100%
75%~99%
LED 1 LED 2 LED 3 LED 4 Current electric
quantity of battery LED 1 LED 2 LED 3 LED 4
Indicator flickers
25%~50%
50%~75%
Indicator is off
Indicator is normally on
5.3.2 Indicator
As shown in the picture below, the remote control is fitted with 4 white LED indicators to indicate the
electric quantity and other status.
5.3.3 Remote Control Frequency Pairing
The Atom SE remote control and the drone can be used immediately after startup, for they have passed frequency
pairing before leaving factory. Where the remote control or the drone is replaced, make sure to conduct frequency
pairing for them as follows prior to use:
Method 1:
1. Shut down the remote control, hold the “Record” and “Power”
button at the same time and do not release them until hearing
two “beep” sounds; the remote control enters frequency pairing
status when power indicators flicker quickly at the same time.
2. After powering on the drone, long press “Power” button and do
not release it until the indicator flickers quickly in green; at this
time, the drone has entered frequency pairing status.
3. Wait for about 30s, and frequency pairing will succeed when
hearing one “beep” sound of the remote control. Connect the
mobile device, open the App and the interface will show the
image transmission image of the drone.
Charging indication
0%~10%
75%~100%
50%~75%
10%~25%
25%~50%
LED 1 LED 2 LED 3 LED 4
Power indication (in use)
Status indication
Frequency pairing
Upgrade mode
Start calibration
Flickers slowly at the same time
Flickers slowly at the same time
Waterflow light
Current electric
quantity of battery
LED 1
LED 2 LED 3
LED 4

Wider communication angle is
ensured at a close distance in
this mode.
5.4 Antenna Angle
Adjust the antenna angle along with the changes of drone height and distance, to ensure the best communication
status of the remote control.
Method 2:
1. Turn on the remote control and connect mobile device, enter APP setting, click “Rematch the drone” to enter the
frequency pairing interface.
2. After powering on the drone, long press the “Power” button and do not release it until the drone indicator flickers
quickly in green; At this time, the drone has entered frequency pairing status.
3. Wait for about 7s, frequency pairing succeeds when you hear one “beep” sound, the flight interface of APP will
show the image transmission image of the drone.
17
Keep the remote control closer to the drone during frequency pairing. Method 2 is recommended to have faster
frequency pairing.
If frequency pairing fails, check if there are interferences nearby, or other drones are also in frequency pairing mode,
or the remote control is too far away or blocked. Eliminate the problems above and try again.
Do not relocate or handle the remote control and the drone during frequency pairing.
Keep two antennas dead against the
drone, to acquire the best directivity,
i.e. longer operation distance.
If the drone is right above
user, this angle can ensure
best communication effect.
Do not cross the antenna in any case. Do not press the antenna on your mobile device in any case.
EN

18
6. PotensicPro APP
6.1 APP Homepage
Click it to switch the model. Model
will be switched automatically if
user has connected the remote
control
Click it to view the teaching video,
instruction, flight record, flight log
Click it to enter flight interface
Display connection status
Homepage of APP
Photo album in APP (Connect the
drone to see the contents in the
drone SD card)
Me: Report the problem, modify
account, browse user agreement,
close account and find the missing
drone.

3. Flight mode:
19
6.2 Flight Interface
9. Set button
Including main controller setting, calibration setting, remote control setting, smart battery information and general setting.
Main controller setting
Beginner mode: New user will enter beginner mode by default. In this mode, speed will be limited at “video” mode, while the
height and distance will be restricted within 30m.
It also includes height limit, distance limit, speed setting and circle parameter setting
Calibration setting
User can calibrate the compass and the remote control manually in this interface
Remote control setting
Control stick mode: Mode 1 (Left Hand Throttle), Mode 2 (Right Hand Throttle)
Rematch the drone: Rematch is required after the drone or the remote control is replaced
Smart battery information
User can view the status and health condition of smart battery in this interface
General setting
User can set measurement unit, decoding mode, view device SN code, firmware version and upgrade firmware in this interface
1. Return button:
2. Navigation prompt bar:
4. Head / Headless mode:
5. Positioning mode:
6. GPS status:
8. Electric quantity of smart battery:
100
Normal
Sport
Video
Attitude mode, no positioning
Visual positioning
GPS positioning
Display the strength of image transmission
connection signal between the drone and the remote
control
Click it to return to the homepage
Display drone status and flight mode
Headless mode
Head mode
7. Signal quality of HD image transmission:
Display GPS signal status and quantity of
satellites searched
3 5
6
7
8
4
9
16 15
17
18
12
10
11
12
13
14
Predicted Flight Duration
EN