Protech Systems PA-6222 User manual

Specifications
PI230
PA-6222 [stand-less or Normal-stand]
This Quick Reference Guide
Power Cord
Driver CD
If you discover any item below was damaged
or lost, please contact your vendor.
Packing Checklist
SystemView
Power Adaptor
VFD (Optional)
I/O View
Qui k
Ref nce
Gui e
c
ere
d
PA- 6222
PA-6222
Stand-less Type
Version Q2
All Right Reserved Copyright 2014
355.19
320
218
238.95
303.85
Normal Stand Type
215.31
236.18
277.84
50
58
58
320
261.71
CPU Intel® Celeron® Processor J1900
Memory DDR3L SO-DIMM(up to 8GB)
Network 10/100/1000Mbps
Power Supply 72 Wapower adaptor
Audio 2W speaker
System Weight Approx.5kg
Dimension(WxHxD) 320 x 303 x 236 mm
OS support POSReady7 / Win8 / Win10
System
Mounng Type Support VESA 75/ 100
Storage SATA 1 x 2.5” HDD or SSD
USB 4 x USB on rear, 1 x USB on side bezel
Serial Ports 3 x RJ45, 1 x RJ45 oponal(+5V/12V selectable)
LAN 1 x RJ45
VGA 1 x DB15
Line Out 1 x phone jack
Cash Drawer 1 x RJ11(+12/24V selectable)
I/O Ports
DC-in 1 x 4pin DC Power Jack
Customer Display VFD, 20 columns and 2 lines, 5 x 7 dots per column
MSR & iBuon JIS-I or II, ISO Track1+2+3
2nd Display 8” or 10.4” LCD
Peripheral
Fingerprint 8-bit grayscale, reader
Resoluon 1024 x 768
Brightness 500 cd/m
2
LED Backlight
Display
Touch Screen Bezel-Free 5-wire resisve
EMC & Safety CE / FCC
Operang Temp. 0 ~ 35℃
Storage Temp. -5 ~ 60℃
Environment
Humidity 20 ~ 90%
All Rights Reserved. Copyright 2017
PA-6222
PA-6222 PA-6222

HDD Mai
®
PA-6222
COM /Cash Drawer
ntenance
All Right Reserved Copyright 2012
Safety Precaution
Stand-less Type
Normal Stand Type
Caution:
1. Voltage of external COM1, COM2, COM3 ports and Cash Drawer port
are made to control on BIOS for your convenience.
The corresponding jumpers "JP_COM1", "JP_COM2", "JP_COM3" and
"JP29" are set open (no jumper connection) by default.
2. "JP_COM1", "JP_COM2", "JP_COM3", "JP29" are enabled when
Voltage adjustment is disabled on BIOS
3. Voltage control is adjustable by BIOS or jumpers. Either way cannot be
applied simultaneously in case of system error, component damage or
serious boot failure.
12” Fanless POS Terminal with Intel Celeron J1900
Step 3.
Remove the side screws.
Step 4.
Remove the
top screw.
Step 1.
Remove the two screws
Step 2.
Open the HDD
cover. Step 5.
Push down HDD chassis.
Step 6.
Pull the HDD Track
Edge out and take
out the HDD.
All Rights Reserved. Copyright 2017
A
A
-6222 on a sturdy, level surface. Be sure to
allow
-6222Operate the P
Always shut
in strong vibration may cause hard disk failure.
The following messages are safety reminders on how to protect your
system from damages, and extend the life cycle of the system.
1. Check the Line Voltage
Make sure the operating voltage range is between 100V and 240V AC;
otherwise, the system could be damaged.
2. Environmental Conditions
Place your P
enough space around the system to have easy access needs.
Avoid installing the system in extremely hot or cold places.
Avoid exposure to sunlight for a long period of time or in an airtight
room.
Avoid the system from any heating device or using the PA-6222
when it has been left outdoors in a cold winter day.
Bear in mind that the operating
and 35°C (32°F~ 95°F).
Avoid moving the system rapidly from a hot place to a cold place, and
vice versa, because condensation may occur inside the system.
Do not place the system too close to any radio-active device.
Radio-active device may cause signal interference.
down the operating system before turning off the power.
ambient temperature is between 0°C
3. Handling
Avoid placing heavy objects on the top of the system.
Do not turn the system upside down. This may cause the hard drive to
malfunction.
Do not allow any objects to fall into this product.
If water or other liquid spills into this product, unplug the power cord
immediately.
4. Good Care
When the outside case gets stained, remove the stains using neutral
washing agent with a dry cloth.
Never use strong agents such as benzene and thinner to clean the
surface of the case.
If heavy stains are present, moisten a cloth with diluted neutral washing
agent or alcohol and then wipe thoroughly with a dry cloth.
If dust is accumulated on the case surface, remove it using a special
vacuum cleaner for computers.
Do not replace the motherboard battery by yourself, or serious damage
may occur.