Protech Systems PA-3222 User manual

USER
MANUAL
PA-3222
10.1” POS Terminal
Powered by Intel®Celeron®
J1900 Quad-Core
PA-3222 M1

PA-3222 POS System
With SATA/ 3COM/5USB
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in May 2017. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have high
electrical voltage. We strongly recommend that only qualified
engineers are allowed to service and disassemble the
system. If any damages should occur on the system and are
caused by unauthorized servicing, it will not be covered by
the product warranty. Please operate the LCD and
Touchscreen with extra care as they can break easily.

i
Contents
Revision History .............................................................................................ix
1Introduction .........................................................................................1-1
1.1 About This Manual ....................................................................1-2
2Getting Started ....................................................................................2-1
2.1 Package List..............................................................................2-2
2.2 System Views Without i-Button and Fingerprint Modules.........2-3
2.2.1 Front View .........................................................................2-3
2.2.2 Rear View..........................................................................2-3
2.2.3 Top View............................................................................2-4
2.2.4 Bottom View ......................................................................2-5
2.2.5 Quarter View......................................................................2-5
2.2.6 Side View...........................................................................2-6
2.3 System Views With i-Button Module.........................................2-7
2.3.1 Front View .........................................................................2-7
2.3.2 Rear View..........................................................................2-7
2.3.3 Top View............................................................................2-8
2.3.4 Bottom View ......................................................................2-9
2.3.5 Quarter View......................................................................2-9
2.3.6 Side View.........................................................................2-10
2.4 System Views With Fingerprint Module ..................................2-11
2.4.1 Front View .......................................................................2-11
2.4.2 Rear View........................................................................2-11
2.4.3 Top View..........................................................................2-12
2.4.4 Bottom View ....................................................................2-13
2.4.5 Side View.........................................................................2-13

ii
2.5 System Specifications .............................................................2-14
2.6 Safety Precautions..................................................................2-16
3System Configuration.........................................................................3-1
3.1 External System I/O Ports Diagram & Pin Assignment.............3-2
3.1.1 Rear I/O Ports Diagram.....................................................3-2
3.2 Jumper & Connector Quick Reference Table............................3-3
3.3 Component Locations Of System Main Board..........................3-4
3.3.1 Top View of System Main Board .......................................3-4
3.4 How To Set Jumpers.................................................................3-6
3.5 Function Buttons and I/O Ports.................................................3-8
3.5.1 Power Button.....................................................................3-8
3.5.2 DC_IN Port (DC_IN)..........................................................3-8
3.5.3 VGA Port (VGA).................................................................3-8
3.5.4 COM Ports (COM1, COM2, COM3)..................................3-9
3.5.5 USB Ports (USB0, USB1, USB2, USB3, USB5).............3-10
3.5.6 LAN Port (LAN)................................................................3-10
3.5.7 Cash Drawer Port (DRW1)..............................................3-11
3.6 Setting Main Board Connectors and Jumpers ........................3-12
3.6.1 COM, Cash Drawer Port Voltage Selection (JP_COM2,
JP_COM3).......................................................................3-12
3.6.2 COM Connectors (COM1_1, COM2_1, COM3_1, COM4_1)
.........................................................................................3-13
3.6.3 i-Button Connector (I-BUT)..............................................3-13
3.6.4 COM2 & i-Button Function Selection (JP10, JP11, JP12)
.........................................................................................3-13
3.6.5 Cash Drawer Control Selection (JP15) ...........................3-14

iii
3.6.6 USB Connectors (USB6, USB7) .....................................3-18
3.6.7 LED Connector (LED1) ...................................................3-19
3.6.8 Speaker Connector (SPK1_1).........................................3-19
3.6.9 Power Connectors (DC12V, DC24V) ..............................3-20
3.6.10 Inverter Connector (INV1) ...............................................3-21
3.6.11 Reserved Connectors (SPK2_1, GPIO1)........................3-21
3.6.12 Panel Resolution Selection (JP5, JP6)............................3-22
3.6.13 Mini PCIE USB Selection (JP13).....................................3-22
3.6.14MSR / Card Reader Connector (PS2).............................3-23
3.6.15 LVDS Connector (LVDS1) ...............................................3-24
3.6.16 Touch Panel Signal Interface Selection (JP8, JP9).........3-25
3.6.17 SATA & SATA Power Connector (SATA1, SATA2,
SATA_PWR1, SATA_PWR2)...........................................3-26
3.6.18 BIOS Update Selection (JP1)..........................................3-27
3.6.19 Clear CMOS Data Selection (JP2)..................................3-27
3.6.20 LVDS Link (JP16)............................................................3-28
3.6.21 LVDS Voltage Selection (JP17).......................................3-28
3.6.22 Panel Enable Selection (JP20)........................................3-29
3.6.23 Mini-PCIe Connector (M_PCI_E1)..................................3-29
3.7 Printer Board Component Locations & Pin Assignment .........3-30
3.7.1 Printer Board: PDAC-3100..............................................3-30
3.7.2 Jumper & Connector Quick Reference Table..................3-31
3.7.3 Setting Printer Board Connectors and Jumpers: PDAC-3100
.........................................................................................3-32
3.7.3.1 Power Supply Connector .............................................3-32
3.7.3.2 RS-232 Interface Connector ........................................3-32
3.7.3.3 Auto-Cutter Connector.................................................3-33
3.7.3.4 USB Connector............................................................3-33
3.7.3.5 Thermal Head/Motor/Sensor Connector......................3-34
3.7.3.6 Terminal Assignment Connector ..................................3-36

iv
3.7.4 Printer Board: MB-1030 series........................................3-37
3.7.4.1 Jumper & Connector Quick Reference Table...............3-38
3.7.5 Setting Printer Board Connectors and Jumpers..............3-39
3.7.5.1 Power Supply Connector .............................................3-39
3.7.5.2 RS-232 Interface Connector ........................................3-39
3.7.5.3 Thermal Head/Motor/Sensor Connector......................3-40
3.7.5.4 Auto-Cutter Connector.................................................3-42
3.7.5.5 Paper-Near-END Sensor Connector............................3-42
3.7.5.6 USB Interface Connector.............................................3-43
3.7.5.7 Terminal Assignment Connector ..................................3-43
3.7.6 Printer Board: MB-1011 & MB-1013................................3-44
3.7.6.1 Jumper & Connector Quick Reference Table...............3-45
3.7.7 Setting Printer Board Connectors and Jumpers: MB-1011 &
MB-1013..........................................................................3-46
3.7.7.1 Power Supply Connector .............................................3-46
3.7.7.2 RS-232 Interface Connector ........................................3-46
3.7.7.3 Auto-Cutter Connector.................................................3-47
3.7.7.4 Thermal Head/Motor/Sensor Connector......................3-47
3.7.7.5 Terminal Assignment Connector ..................................3-49
3.7.7.6 USB Interface Connector.............................................3-49
3.8 VFD Board Component Locations & Pin Assignment.............3-50
3.8.1 VFD Board: MB-4103, LD720 .........................................3-50
3.8.2 Jumper & Connector Quick Reference Table..................3-51
3.8.3 Setting MB-4103 & LD720 VFD Board Connectors and
Jumpers...........................................................................3-52
3.8.3.1 Power Switch Selection ...............................................3-52
3.8.3.2 RS-232 Serial Interface Connector..............................3-53
3.9 MSR Board Component Locations & Pin Assignment............3-54

v
3.9.1 ID TECH ..........................................................................3-54
3.9.1.1 Main Connector............................................................3-54
3.9.2 MB-3012..........................................................................3-55
3.9.2.1 Information Button Reader...........................................3-55
3.9.2.2 Output Connector.........................................................3-55
4Software Utilities.................................................................................4-1
4.1 Introduction................................................................................4-2
4.2 Installing Intel®Chipset Software Installation Utility..................4-3
4.2.1 Installing Intel®Chipset Driver...........................................4-3
4.3 Installing VGA Driver Utility.......................................................4-4
4.4 Installing LAN Driver Utility........................................................4-4
4.5 Installing Sound Driver Utility....................................................4-6
4.6 Installing Fingerprint Driver Utility (Optional) ............................4-7
4.7 Installing RFID Module Driver Utility (Optional) ........................4-7
4.8 Installing Wireless Module Driver Utility (Optional)...................4-8
4.9 Peripheral Devices....................................................................4-9
4.9.1 Printer Board: MB-1030.....................................................4-9
4.9.1.1 Commands List..............................................................4-9
4.9.1.2 OPOS Printer Driver.....................................................4-55
4.9.2 VFD: MB-4103 (RS-232).................................................4-63
4.9.2.1 Commands List............................................................4-63
4.9.2.2 OPOS Driver ................................................................4-64
4.9.3 MSR: MB-3102 (PS/2).....................................................4-69
4.9.3.1 OPOS Driver ................................................................4-69
4.9.4MSR: GIGA-TMS MJR243 (RS-232)...............................4-75
4.9.4.1 Commands List............................................................4-75

vi
4.9.4.2 OPOS MSR Register ...................................................4-77
4.9.4.3 OPOS MSR Tester.......................................................4-85
4.10 API...........................................................................................4-89
4.10.1 API Package Content......................................................4-89
4.10.2 API Procedure.................................................................4-90
4.10.3 Cash Drawer....................................................................4-93
4.10.4 Watchdog.........................................................................4-94
4.11 API Function............................................................................4-95
4.11.1 Cash Drawer Function.....................................................4-95
4.11.2 Watch Dog Function........................................................4-96
5BIOS SETUP ........................................................................................5-1
5.1 Introduction................................................................................5-2
5.2 Accessing Setup Utility..............................................................5-3
5.3 Main...........................................................................................5-7
5.4 Advanced ..................................................................................5-9
5.4.1 Advanced –ACPI Settings ..............................................5-10
5.4.2 Advanced –F81866 Super IO Configuration ..................5-11
5.4.3 Advanced –Hardware Monitor........................................5-17
5.4.4 Advanced –F81866 Watchdog Configuration.................5-18
5.4.5 Advanced –CPU Configuration ......................................5-19
5.4.6 Advanced –CPU Configuration > Socket 0 CPU Information
.........................................................................................5-20
5.4.7 Advanced –IDE Configuration (AHCI Mode)..................5-22
5.4.8 Advanced –OS Selection ...............................................5-24
5.4.9 Advanced –CSM Configuration......................................5-25
5.4.10 Advanced –USB Configuration.......................................5-27

vii
5.5 Chipset ....................................................................................5-28
5.5.1 North Bridge ....................................................................5-29
5.5.1.1 North Bridge –LCD Control.........................................5-30
5.5.2 South Bridge....................................................................5-31
5.6 Security ...................................................................................5-32
5.7 Boot.........................................................................................5-33
5.7.1 Boot –Hard Drive BBS Priorities.....................................5-34
5.8 Save & Exit..............................................................................5-35
Appendix A System Diagrams....................................................A-1
Exploded Diagram For System Top Case ................................................A-2
System Exploded Diagram.......................................................................A-3
Exploded Diagrams For System LCD Panel ............................................A-5
Exploded Diagrams For System LCD Panel ............................................A-6
Exploded Diagrams For System LCD Panel ............................................A-7
Exploded Diagram For HDD.....................................................................A-8
Exploded Diagram For MSR Module........................................................A-9
Exploded Diagram For Fingerprint Module ............................................A-10
Exploded Diagram For 3-Inch Printer (1) ...............................................A-11
Exploded Diagram For 3-Inch Printer (2) ...............................................A-12
Exploded Diagram For 2-Inch Printer (1) ...............................................A-13
Exploded Diagram For 2-Inch Printer (2) ...............................................A-14
Exploded Diagram For VFD Module ......................................................A-16
Appendix B Technical Summary................................................B-1
Interrupt Map ............................................................................................B-2
DMA MAP .................................................................................................B-5
I/O Map.....................................................................................................B-6
Memory Map.............................................................................................B-8