protech POS-6511 Series User manual

USER’S
MANUAL
POS-6511 Series
POS System Powered by
Intel
®
Sandy Bridge Platform
PO
S
-
6
5
1
1
Series
M
1

Preface
POS-6511 Series POS System
With LCD / Touchscreen
PREFACE
COPYRIGHT NOTICE
This user’s manual is meant to assist users in installing and setting up the
system. The information contained in this document is subject to change
without any notice.
This manual is copyrighted March 2012. You may not reproduce or transmit
in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Preface
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And
therefore we strongly recommend that qualified engineers can open and disassemble the
system.
The LCD and Touchscreen are easily breakable, please handle them with extra care.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ....................................................... 1-2
1-2 POS System Illustration ................................................ 1-3
1-3 System Specifications ................................................... 1-6
1-4 Safety Precautions ......................................................... 1-8
CHAPTER 2 SYSTEM CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ............... 2-2
2-2 Component Locations ................................................... 2-3
2-3 How to Set the Jumpers ................................................ 2-5
2-4 COM Port Connector ………………………………… 2-7
2-5 COM Port RI and Voltage Selection ………………… 2-10
2-6 VGA Connector ……………………………………… 2-11
2-7 I-Button Connector …………………………………… 2-12
2-8 I-Button Function Selection ………………………….. 2-12
2-9 LAN & USB Connector …………………………….... 2-13
2-10 USB Connector ……………………..……..…………. 2-14
2-11 Mini-DIN & USB Connector …………….................... 2-15
2-12 Cash Drawer Connector …………………………….... 2-16
2-13 Cash Drawer Power Selection ………………………... 2-16
2-14 LED Connector ………………………………………. 2-17
2-15 Power Connector ……………………………………... 2-17
2-16 Power Switch Connector …………………..………..... 2-17
2-17 Fan Connector ………………………………………… 2-18
2-18 External Speaker Connector ………………………….. 2-19
2-19 Inverter Connector ……………………………………. 2-19
2-20 Backlight Type Selection ……..………………………. 2-19
2-21 MSR/ Card Reader Connector ……………………....... 2-20
2-22 LVDS Voltage Selection ……………………………... 2-20
2-23 LVDS Connector ……………………………………... 2-21
2-24 SATA & SATA Power Connector …………………… 2-22
2-25 Touch Panel Connector ………………………………. 2-23
2-26 Touch Panel Selection ………………………………... 2-23
2-27 Clear CMOS Data Selection ……………………..…… 2-24
2-28 Compact Flash Connector ……………………………. 2-25
2-29 Printer Connector …………………………………….. 2-26

Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction ................................................................... 3-2
3-2 Intel
®
Chipset Software Installation Utility ................... 3-3
3-3 VGA Driver Utility …………………………….…….. 3-4
3-4 LAN Driver Utility ....................................................... 3-5
3-5 Sound Driver Utility ..................................................... 3-6
3-6 Touch Screen Driver Utility ……………..…………… 3-7
3-7 Wireless Driver Utility (Optional) …………………… 3-8
CHAPTER 4 AMI BIOS SETUP
4-1 Introduction ................................................................... 4-2
4-2 Entering Setup ............................................................... 4-4
4-3 Main ….......................................................................... 4-6
4-4 Advanced ….................................................................. 4-7
4-5 Chipset ……………………………............................... 4-24
4-6 Boot ............................................................................... 4-32
4-7 Security ……................................................................. 4-35
4-8 Save & Exit ................................................................... 4-37
APPENDIX A SYSTEM ASSEMBLY
Exploded Diagram for POS-6511 System with Stand ……….. A-2
Exploded Diagram for POS-6511 System Assembly ….…….. A-3
Exploded Diagram for POS-6511 Back Cover Assembly ….... A-4
Exploded Diagram for POS-6511 Top Cover Assembly …….. A-5
Exploded Diagram for POS-6511 Mainboard Assembly …….. A-12
Exploded Diagram for POS-6511 Touch Panel Assembly .….. A-13
Exploded Diagram for POS-6511 Case Assembly ................... A-15
Exploded Diagram for POS-6511 Stand Assembly ………….. A-16
Exploded Diagram for POS-6511 Power Assembly …………. A-22

Contents
APPENDIX B TECHNICAL SUMMARY
Block Diagram .......................................................................... B-2
Interrupt Map ............................................................................ B-3
DMA Channels Map ................................................................. B-7
Memory Map ............................................................................ B-8
I/O Map .................................................................................... B-10
Watchdog Timer Configuration ................................................ B-13
Flash BIOS Update ……........................................................... B-15
APPENDIX C QUICK MANUAL
Assembly Procedure of VFD .................................................... C-2
i-Button Decoder API ............................................................... C-5

Page:1-1
INTRODUCTION
This chapter gives you the information for the POS-6511. It also outlines
the system specifications.
Sections included:
About This Manual
POS System Illustration
System Specifications
Safety Precautions
Experienced users can jump to chapter 2 on page 2-1
for a quick start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2 POS-6511 SERIES USER
 S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our POS-6511 Series System. The POS-6511 is an
updated system designed to be comparable with the highest performance of
IBM AT personal computers. The POS-6511 provides faster processing speed,
greater expandability and can handle more tasks than before. This manual is
designed to assist you how to install and set up the whole system. It contains
four chapters and three appendixes. Users can configure the system according
to their own needs.
Chapter 1 Introduction
This chapter introduces you to the background of this manual. It also includes
illustrations and specifications for the whole system. The final section of this
chapter indicates some safety reminders on how to take care of your system.
Chapter 2 System Configuration
This chapter outlines the location of motherboard components and their
function. You will learn how to set the jumper and configure the system to
meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the Intel
Utility, VGA Utility, LAN Utility, Sound Utility, and Touch Screen Utility. It
also describes the Wireless Utility.
Chapter 4 AMI BIOS Setup
This chapter indicates you how to change the BIOS configurations.
Appendix A System Assembly
This appendix gives you the exploded diagrams and part numbers of the POS-
6511.
Appendix B Technical Summary
This appendix gives you the information about the allocation maps for the
system resources, Watchdog Timer Configuration, and Flash BIOS Update.
Appendix C Quick Manual
This appendix gives you the information about the VFD assembly procedures
and the i-Button decoder API.

Chapter 1 Introduction
POS-6511 SERIES USER  S MANUAL Page: 1-3
1-2. POS SYSTEM ILLUSTRATION
POS-6511

Chapter 1 Introduction
Page: 1-4 POS-6511 SERIES USER
 S MANUAL
POS-6511-PPC

Chapter 1 Introduction
POS-6511 SERIES USER  S MANUAL Page: 1-5
POS-6511-MIT

Chapter 1 Introduction
Page: 1-6 POS-6511 SERIES USER
 S MANUAL
1-3. SYSTEM SPECIFICATIONS
MAINBOARD (PB-6056RA)
CPU Type (with North Bridge):
Intel®Celeron B810, 1.60GHz
Intel®Core i3-2330E processor, 2.2GHz
Chipset:
Intel
®HM65
Memory:
1 x 204-pin DDRIII SO-DIMM socket on board, up to 4GB
Cache:
Depended on CPU
Real-Time Clock / Calendar:
Embedded in Intel®HM65 South Bridge
BIOS:
AMI SPI BIOS, 64Mbits with VGA BIOS
Keyboard & Mouse Connector:
PS/2 Keyboard, combined with mini-DIN
Serial Port:
1 x RJ45 (COM4), 3 x DB-9 (COM 1/2/3)
+5/12V Selectable (COM 1~4)
Universal Serial Bus Port:
4 x USB2.0 ports
1 x USB2.0 on side bezel
PARALLEL PORT:
1 x parallel port, bi-directional, supports SPP/EPP/ECP
LAN Function:
1 x 10/100/1000 Mbps

Chapter 1 Introduction
POS-6511 SERIES USER  S MANUAL Page: 1-7
Audio Function:
1 x 2W Speaker
VGA Function:
1 x DB-15 VGA Interface
Dimension (W x H x D):
[POS-6511] : 365 x 363 x 297 mm (14.37” x 14.37” x 11.69”)
[POS-6511-PPC] : 365 x 318 x 70 mm (14.37” x 12.54” x 2.76”)
[POS-6511-MIT] : 365 x 421.5 x 70 mm (14.37” x 16.59” x 2.76”)
System Weight:
[POS-6511] : 9kg (19.84lb)
[POS-6511-PPC] : 5.5kg (12.13lb)
[POS-6511-MIT] : 7.4kg (16.31lb)
LCD Panel:
Type XGA
Max. Resolution 1024 x 768
Size/Type 15” / TFT
Viewing Angel (degree) 0~65 degrees
Pixel Pitch 0.297(H) x 0.297(V)
Brightness 250 cd / m2
Signal Interface (bit) TTL (24-bit)
Touch Panel:
15” 5wire Analog resistive
WIRELESS LAN (Optional):
Mini PCI-e Wireless LAN Module (802.11b/g)
MSR / Fingerprint (Optional):
External vertical module, MSR, Read only, ISO Tracker 1+2+3 (PS/2 KB
Interface) + Fingerprint (USB Interface)
MSR / i-Button / RFID (Optional):
External vertical module, MSR, Read only, JIS-I or II, ISO Tracker 1+2+3;
I-button, Read only; RFID, Read / Write, ISO 14443A 13.56MHz (USB
Interface)

Chapter 1 Introduction
Page: 1-8 POS-6511 SERIES USER
 S MANUAL
1-4. SAFETY PRECAUTIONS
The following messages are safety reminders on how to protect your systems
from damages, and extending the life cycle of the system.
1. Check the Line Voltage
a. The operating voltage for the power supply should be within the range of
100V to 240V AC; otherwise the system may be damaged.
2. Environmental Conditions
a. Place your POS-6511 on a sturdy, level surface. Be sure to allow
enough space around the system to have easy access needs.
b. Avoid installing your POS-6511 Series POS system in extremely hot or
cold places.
c. Avoid exposure to sunlight for a long period of time (for example, in a
closed car in summer time. Also avoid the system from any heating
device.). Or do not use the POS-6511 when it has been left outdoors in a
cold winter day.
d. Bear in mind that the operating ambient temperature is between 0C and
35C (32F and 95F).
e. Avoid moving the system rapidly from a hot place to a cold place, and
vice versa, because condensation may occur inside the system.
f. Protect your POS-6511 against strong vibrations, which may cause hard
disk failure.
g. Do not place the system too close to any radio-active device. Radio-
active device may cause signal interference.
h. Always shutdown the operating system before turning off the power.
3. Handling
a. Avoid placing heavy objects on the top of the system.
b. Do not turn the system upside down. This may cause the hard drive to
malfunction.
c. Do no allow any objects to fall into this product.
d. If water or other liquid spills into the product, unplug the power cord
immediately.

Chapter 1 Introduction
POS-6511 SERIES USER  S MANUAL Page: 1-9
4. Good Care
a. When the outside case gets stained, remove the stains using neutral
washing agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the surface
of the case.
c. If heavy stains are present, moisten a cloth with diluted neutral washing
agent or alcohol and then wipe thoroughly with a dry cloth.
d. If dust is accumulated on the case surface, remove it by using a special
vacuum cleaner for computers.

Page 2-1
SYSTEM
CONFIGURATION
Helpful information that describes the jumper and connector settings,
and component locations.
Sections included:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector Pin Assignments
CHAPTER
2

Chapter 2 System Configuration
Page: 2-2 POS-6511 SERIES USER
’ S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
Connector & Jumper Name Page
COM Port Connector COM1, COM2, COM3, COM4,
COM4_1 2-7
COM Port RI and Voltage Selection
JP_COM1, JP_COM2, JP_COM3,
JP_COM4 2-10
VGA Connector VGA1 2-11
I-Button Connector I_BUTTON1 2-12
I-Button Function Selection JP15, JP16, JP17 2-12
LAN & USB Connector JRJ45USB1 2-13
USB Connector USB1, USB2, USB3 2-14
Mini-DIN & USB Connector JPS2USB1 2-15
Cash Drawer Connector DRW1 2-16
Cash Drawer Power Selection JP18 2-16
LED Connector LED1 2-17
Power Connector J1 2-17
Power Switch Connector SW1 2-17
Fan Connector CPU_FAN1, SYS_FAN1, SYS_FAN2 2-18
External Speaker Connector SPK1 2-19
Inverter Connector INV1 2-19
Backlight Type Selection JP13 2-19
MSR / Card Reader Connector PS1 2-20
LVDS Voltage Selection JP12 2-20
LVDS Connector LVDS1 2-21
SATA & SATA Power Connector SATA1, JPWR_4P1 2-22
Touch Panel Connector JTP1 2-23
Touch Panel Selection JP20 2-23
Clear CMOS Data Selection JP7 2-24
Compact Flash Connector CF1 2-25
Printer Connector LPT1 2-26

Chapter 2 System Configuration
POS-6511 SERIES USER’S MANUAL Page: 2-3
2-2. COMPONENT LOCATIONS
M/B: PB-6056RA
1
5
1
111
1
2
5
6
6 5
2
1
2
5
6
7
8
1
2
6 5
2 1
7
8
1
2
1
2 30
29
1
6
6
1 2
6
1 2
12
51
106
6
5
2
1
Battery
I_BUTTON1
203
73
2
72 71
74
1
204
203
73
2
72 71
74
1
204
1
JPS2USB1
4
9
13 14
12
85
JRJ45USB1
1
210
9
COM4
43
PWR_IN1
21
19
10 2
1
1
14
13
25
5
6
9
15
6
9
VGA1
41
11
POS-6511 Mainboard Front Connector, Jumper and Component locations

Chapter 2 System Configuration
Page: 2-4 POS-6511 SERIES USER
’ S MANUAL
POS-6511 Mainboard Rear Connector, Jumper and Component locations

Chapter 2 System Configuration
POS-6511 SERIES USER ’ S MANUAL Page: 2-5
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting the jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by using
a small plastic "cap", Also known as the jumper cap (with a metal contact
inside), you are able to connect the pins. So you can set-up your hardware
configuration by "opening"or "closing"pins.
The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins for example, labelled PIN1, PIN2, and PIN3. You
can connect PIN1 & PIN2 to create one setting and shorting. You can either
connect PIN2 & PIN3 to create another setting. The same jumper diagrams
are applied all through this manual. The figure below shows what the manual
diagrams look and what they represent.