protech POS-6510 Series User manual

USER’S
MANUAL
POS-6510 Series
POS System Powered by
Intel
®
Atom
®
Platform
PO
S
-
6
5
10
Series
M
6

Preface
POS-6510 Series POS System
With LCD / Touchscreen
COPYRIGHT NOTICE
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.
This manual is copyrighted Sep. 2011 (Revised Edition: May 2014). You may
not reproduce or transmit in any form or by any means, electronic, or
mechanical, including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up the
system. The information contained in this document is subject to change
without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Preface
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And
therefore we strongly recommend that qualified engineers can open and disassemble the
system. The LCD and Touchscreen are easily breakable, please handle them with extra
care.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ....................................................... 1-2
1-2 POS System Illustration ................................................ 1-3
1-3 System Specifications ................................................... 1-5
1-4 Safety Precautions ......................................................... 1-7
CHAPTER 2 SYSTEM CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ............... 2-2
2-2 Component Locations ................................................... 2-3
2-3 How to Set the Jumpers ................................................ 2-4
2-4 COM Port Connector ………………………………… 2-6
2-5 COM Port RI and Voltage Selection ………………… 2-8
2-6 VGA Connector ……………………………………… 2-9
2-7 I-Button Connector …………………………………… 2-9
2-8 I-Button Function Selection ………………………….. 2-10
2-9 LAN & USB Connector …………………………….... 2-11
2-10 USB Connector ……………………..……..…………. 2-12
2-11 PS/2 Keyboard & Mouse Connector ……………......... 2-13
2-12 Reset/ NMI Watchdog Selection ……………………... 2-13
2-13 Cash Drawer Connector …………………………….... 2-14
2-14 Cash Drawer Power Selection ………………………... 2-14
2-15 LED Connector ………………………………………. 2-15
2-16 Fan Connector ………………………………………… 2-16
2-17 Power Connector ……………………………………... 2-16
2-18 Power Switch Connector …………………..………..... 2-16
2-19 Reset Switch Connector …………………..…..……… 2-17
2-20 Power for Thermal Printer Connector ………………... 2-17
2-21 External Speaker Connector ………………………….. 2-17
2-22 Inverter Connector …………………………………… 2-18
2-23 Backlight Type Selection ……..……………………… 2-18
2-24 MSR/ Card Reader Connector ……………………...... 2-19
2-25 LVDS Connector ……………………………………... 2-19
2-26 SATA & SATA Power Connector …………………… 2-20
2-27 Touch Panel Connector ………………………………. 2-22
2-28 Touch Panel Interface Type Selection ……………….. 2-23

Contents
2-29 Clear CMOS Data Selection ……………………..…… 2-24
2-30 Compact Flash Connector ……………………………. 2-25
2-31 Printer Connector …………………………………….. 2-26
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction ................................................................... 3-2
3-2 Intel
®
Chipset Software Installation Utility ................... 3-3
3-3 VGA Driver Utility …………………………….…….. 3-4
3-4 LAN Driver Utility ....................................................... 3-5
3-5 Sound Driver Utility ..................................................... 3-6
3-6 Touch Screen Driver Utility ……………..…………… 3-7
3-7 Wireless Driver Utility (Optional) …………………… 3-8
CHAPTER 4 AMI BIOS SETUP
4-1 Introduction ................................................................... 4-2
4-2 Entering Setup ............................................................... 4-3
4-3 Main ….......................................................................... 4-5
4-4 Advanced ….................................................................. 4-6
4-5 Boot ............................................................................... 4-18
4-6 Security ……................................................................ 4-22
4-7 Chipset …………………………….............................. 4-23
4-8 Exit ............................................................................... 4-28
APPENDIX A SYSTEM ASSEMBLY
Exploded Diagram for POS-6510 System with Stand ……….. A-2
Exploded Diagram for POS-6510 System Assembly ….…….. A-3
Exploded Diagram for POS-6510 Headset Assembly ……….. A-5
Exploded Diagram for POS-6510 Back Cover Assembly ….... A-8
Exploded Diagram for POS-6510 Top Cover Assembly …….. A-9
Exploded Diagram for POS-6510 Mainboard Assembly …….. A-13
Exploded Diagram for POS-6510 Touch Panel Assembly .….. A-15
Exploded Diagram for POS-6510 Case Assembly ................... A-17
Exploded Diagram for POS-6510 HDD Assembly ………….. A-19
Exploded Diagram for POS-6510 Heatsink Assembly .……… A-24
Exploded Diagram for POS-6510 Stand Assembly ………….. A-26
Exploded Diagram for POS-6510 Power Assembly …………. A-32
Exploded Diagram for POS-6510 VFD Assembly …………... A-34

Contents
APPENDIX B TECHNICAL SUMMARY
Block Diagram ......................................................................... B-2
Interrupt Map ............................................................................ B-3
DMA Channels Map ................................................................ B-4
I/O Map .................................................................................... B-5
Watchdog Timer Configuration ............................................... B-8
Flash BIOS Update …….......................................................... B-10
APPENDIX C QUICK MANUAL
Assembly Procedure of Back VFD – Model 1 ......................... C-2
Assembly Procedure of Back VFD – Model 2 ......................... C-4
i-Button Decoder API .............................................................. C-6

Page:1-1
INTRODUCTION
This chapter gives you the information for the POS-6510. It also outlines
the system specifications.
Sections included:
About This Manual
POS System Illustration
System Specifications
Safety Precautions
Experienced users can jump to chapter 2 on page 2-1
for a quick start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2 POS-6510 SERIES USER
′ S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our POS-6510 Series System. The POS-6510 is an updated
system designed to be comparable with the highest performance of IBM AT personal
computers. The POS-6510 provides faster processing speed, greater expandability
and can handle more tasks than before. This manual is designed to assist you how to
install and set up the whole system. It contains four chapters and three appendixes.
Users can configure the system according to their own needs.
Chapter 1 Introduction
This chapter introduces you to the background of this manual. It also includes
illustrations and specifications for the whole system. The final section of this chapter
indicates some safety reminders on how to take care of your system.
Chapter 2 System Configuration
This chapter outlines the location of motherboard components and their function. You
will learn how to set the jumper and configure the system to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the Intel Utility,
VGA Utility, LAN Utility, Sound Utility, and Touch Screen Utility. It also describes
the Wireless Utility.
Chapter 4 AMI BIOS Setup
This chapter indicates you how to change the BIOS configurations.
Appendix A System Assembly
This appendix gives you the exploded diagrams and part numbers of the POS-6510.
Appendix B Technical Summary
This appendix gives you the information about the allocation maps for the system
resources, Watchdog Timer Configuration, and Flash BIOS Update.
Appendix C Quick Manual
This appendix gives you the information about the pole VFD assembly procedures
and the i-Button decoder API.

Chapter 1 Introduction
POS-6510 SERIES USER ′ S MANUAL Page: 1-3
1-2. POS SYSTEM ILLUSTRATION
POS-6510 with Stand
365
250
70
8.2
53.2
370.88
75.65
33.9
318.5
270
Front
V
iew
Rear
V
iew
Side View
Top View Bottom View

Chapter 1 Introduction
Page: 1-4 POS-6510 SERIES USER
′ S MANUAL
I/O
V
iew
Quarter View

Chapter 1 Introduction
POS-6510 SERIES USER ′ S MANUAL Page: 1-5
1-3. SYSTEM SPECIFICATIONS
MAINBOARD (PROX-A6510LF)
CPU Type (with North Bridge):
Intel
®
ATOM Pineview D525
Chipset:
Intel
®
ICH8M
Memory:
One 204-pin DDRIII SO-DIMM socket on board, up to 4GB
Cache:
Depended on CPU
Real-Time Clock / Calendar:
Embedded in Intel
®
ICH8M South Bridge
BIOS:
AMI SPI BIOS
8Mbits with VGA BIOS
Keyboard & Mouse Connector:
PS/2 Keyboard, combined with mini DIN connecter on rear panel .
Serial Port:
1 x RJ45 (COM1), 2 x DB-9(COM 2/3)
1 x Wafer (COM4, Wafer or DB-9 optional)
+5/12V Selectable (COM 1~4)
Universal Serial Bus Port:
4 x USB2.0 ports
1 x USB2.0 on side bezel
LAN Function:
1 x 10/100/1000 Mbps

Chapter 1 Introduction
Page: 1-6 POS-6510 SERIES USER
′ S MANUAL
Audio Function:
1 x 2W Speaker
VGA Function:
1 x DB-15 VGA Interface
Dimension (W x H x D):
365mm x 363mm x 303mm
System Weight:
11 kg
LCD Panel:Type XGA
Max. Resolution 1024 x 768
Size/Type 15” / TFT
Viewing Angel
(degree) 0~65 degrees
Pixel Pitch 0.297(H) x 0.297(V)
Brightness 250 cd / m
2
Signal Interface (bit) TTL (24-bit)
Touch Panel:
15” 5wire Analog resistive .
WIRELESS LAN (Optional):
Mini PCI-e Wireless LAN Module (802.11b/g)
MSR / Fingerprint (Optional):
External vertical module, MSR, Read only, ISO Tracker 1+2+3 (PS/2 KB
Interface) + Fingerprint (USB Interface)
MSR / i-Button / RFID (Optional):
External vertical module, MSR, Read only, JIS-I or II, ISO Tracker 1+2+3; I-
button, Read only; RFID, Read / Write, ISO 14443A 13.56MHz (USB Interface)

Chapter 1 Introduction
POS-6510 SERIES USER ′ S MANUAL Page: 1-7
1-4. SAFETY PRECAUTIONS
The following messages are safety reminders on how to protect your systems from
damages, and extending the life cycle of the system.
1. Check the Line Voltage
a. The operating voltage for the power supply should be within the range of
100V to 240V AC; otherwise the system may be damaged.
2. Environmental Conditions
a. Place your POS-6510 on a sturdy, level surface. Be sure to allow enough
space around the system to have easy access needs.
b. Avoid installing your POS-6510 Series POS system in extremely hot or cold
places.
c. Avoid exposure to sunlight for a long period of time (for example, in a
closed car in summer time. Also avoid the system from any heating device.).
Or do not use the POS-6510 when it has been left outdoors in a cold winter
day.
d. Bear in mind that the operating ambient temperature is between 0°C and
35°C (32°F and 95°F).
e. Avoid moving the system rapidly from a hot place to a cold place, and vice
versa, because condensation may occur inside the system.
f. Protect your POS-6510 against strong vibrations, which may cause hard disk
failure.
g. Do not place the system too close to any radio-active device. Radio-active
device may cause signal interference.
h. Always shutdown the operating system before turning off the power.
3. Handling
a. Avoid placing heavy objects on the top of the system.
b. Do not turn the system upside down. This may cause the hard drive to
malfunction.
c. Do no allow any objects to fall into this product.
d. If water or other liquid spills into the product, unplug the power cord
immediately.

Chapter 1 Introduction
Page: 1-8 POS-6510 SERIES USER
′ S MANUAL
4. Good Care
a. When the outside case gets stained, remove the stains using neutral washing
agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the surface of
the case.
c. If heavy stains are present, moisten a cloth with diluted neutral washing
agent or alcohol and then wipe thoroughly with a dry cloth.
d. If dust is accumulated on the case surface, remove it by using a special
vacuum cleaner for computers.

Page 2-1
SYSTEM
CONFIGURATION
Helpful information that describes the jumper and connector settings,
and component locations.
Sections included:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector Pin Assignments
CHAPTER
2

Chapter 2 System Configuration
Page: 2-2 POS-6510 SERIES USER
’ S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
CONNECTOR/JUMPER NAME PAGE
COM Port Connector COM1, COM2, COM2-1,
COM3, COM4_1
2-6
COM Port RI and Voltage
Selection
JP_COM1, JP_COM2,
JP_COM3, JP_COM4
2-8
VGA Connector VGA1 2-9
I-Button Connector JI-BUTTON1 2-9
I-Button Function Selection JP8, JP9, JP10 2-10
LAN & USB Connector JRJ45USB1, LAN1 2-11
USB Connector USB1, USB3, USB5 2-12
PS/2 Keyboard & Mouse
Connector
DIN1 2-13
RESET/NMI Watchdog Selection JP4 2-13
Cash Drawer Connector DRW1 2-14
Cash Drawer Power Selection JP13 2-14
LED Connector LED_1, LED_2, JUSBLED1 2-15
Fan Connector FAN1 2-16
Power Connector J3 2-16
Power Switch Connector SW1, SW2, SW3 2-16
Reset Switch Connector RST_SW1 2-17
Power for Thermal Printer
Connector
PRT_PWR1 2-17
External Speaker Connector SPK1 2-17
Inverter Connector JINV1, JINV2 2-18
Backlight Type Selection JP3 2-18
MSR / Card Reader Connector PS1, PS2 2-19
LVDS Connector LVDS1 2-19
SATA & SATA Power Connector SATA1, JPWR_4P1, SATA2 2-20
Touch Panel Connector TOUCH1, TOUCH2 2-22
Touch Panel Interface Type
Selection
JP38, JP39, JP40, JP41 2-23
Clear CMOS Data Selection JP1 2-24
Compact Flash Connector CF1 2-25
Printer Connector LPT1 2-26

Chapter 2 System Configuration
POS-6510 SERIES USER ’ S MANUAL Page: 2-3
2-2. COMPONENT LOCATIONS
M/B: PB-6055RB
D525 ICH8M
1
1
JP3
JP10
JP8
JP9
JP_COM4
1
2
1
1
56
78
1 2
JP6
1
JP13
6
1
1
33
5
2 1
JP_COM1
JP39JP38
24
1
3
JP4
JP11
JP41
JP40
2 4
1
1
1
2
23
1
JP1
1
2
5
6
JP_COM2
2
5
6
JP_COM3
BZ1
CF1
JI_BUTTON1
1 2
SPK1
1 2
SW3
1
5
TOUCH1
1
2
RST_SW1
LPT1
26
13
14
1
SW1
1
2
1
JP7
1
4
PRT_PWR1
1
USB3
1
USB6
5
1
2
30 29
LVDS1
PWR_IN1
12
3
4
1
2
9
10
A1 A4
B1 B4
14 11
JRJ45USB1
LAN1
1151751
52 18 16 2
M_PCIE1
1
2
3
4
5
LINE-OUT1
Battery
VGA1
51
6
10
11
15
COM2
15
6 9
1 4
5 8
USB1
DRW1
1
2
5
6
91
10 2
COM1
203
73
2
72
71
74
1
204
DIMM1
12
SW2
1
2
LED_1
1
2
JINVDRV1
JINV2
TOUCH2
PS1
1
5
1
4
1
6
SATA1
1
7
JPWR_4P1
1
4
COM2_1
9
1
10
2
5
1
FAN1J3
1
1 6
JINV1
LED_2
PS2
1
USB5
5
COM4_1
6
1
10
5
COM3
9
1
10
1
2
9
10
11
12
13
14
SATA2
1
7
9
21
12 3
4
6 5
DIN1
JUSBLED1
1
2
20
19
SIO
1 6
1 6
1
POS-6510 Mainboard Connector, Jumper and Component locations

Chapter 2 System Configuration
Page: 2-4 POS-6510 SERIES USER
’ S MANUAL
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting the jumpers. Jumper is consists of two or three
metal pins with a plastic base mounted on the card, and by using a small plastic "cap",
Also known as the jumper cap (with a metal contact inside), you are able to connect the
pins. So you can set-up your hardware configuration by "opening"or "closing"pins.
The jumper can be combined into sets that called jumper blocks. When the jumpers are
all in the block, you have to put them together to set up the hardware configuration. The
figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins for example, labelled PIN1, PIN2, and PIN3. You can
connect PIN1 & PIN2 to create one setting and shorting. You can either connect PIN2
& PIN3 to create another setting. The same jumper diagrams are applied all through
this manual. The figure below shows what the manual diagrams look and what they
represent.

Chapter 2 System Configuration
POS-6510 SERIES USER ’ S MANUAL Page: 2-5
JUMPER DIAGRAMS
JUMPER SETTINGS

Chapter 2 System Configuration
Page: 2-6 POS-6510 SERIES USER
’ S MANUAL
2-4. COM PORT CONNECTOR
There are four COM ports enhanced in this board namely: COM1, COM2, COM2_1,
COM3 and COM4_1.
Caution: When using a 72W power adaptor, do not set the voltage at “12V” for three COM
ports or above; otherwise, the system may shut down due to power deficiency.
COM1: COM1 Connector
The pin assignments are as follows:
PIN ASSIGNMENT
1 DCD1
2 RXD1
3 TXD1
4 DTR1
5 GND
6 DSR1
7 RTS1
8 CTS1
9 RI / +5V / +12V selectable
10 NC
COM2 / COM3 / COM4: COM2/ COM3/ COM4 Connector
The pin assignments are as follows:
PIN ASSIGNMENT
1 DCD2/3/4
2 RXD2/3/4
3 TXD2/3/4
4 DTR2/3/4
5 GND
6 DSR2/3/4
7 RTS2/3/4
8 CTS2/3/4
9 RI / +5V / +12V selectable
Note: The COM4 connector can be optional Wafer or DB-9 as request.
5
9
1
6
COM2
COM3
COM4
COM1