protech PA-3055 User manual

Manual
PA-3055
15” POS Terminal
Powered by Intel
®
Celeron
®
J1900 Quad-Core
PA-3055 M1

PA-3055 POS System
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted Jan. 2014. You may not reproduce or transmit in any
form or by any means, electronic, or mechanical, including photocopying and
recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up the system. The
information contained in this document is subject to change without any notice.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And
therefore we strongly recommend that qualified engineers can open and disassemble the
system.The LCD and Touchscreen are easily breakable, please handle them with extra
care.

INTRODUCTION
This chapter gives you the information for the PA-3055. It also
outlines the system specifications.
Sections included:
About This Manual
POS System Illustration
System Specifications
Safety precautions
Experienced users can jump to chapter 2 on page 2-1
for a quick start.
CHAPTER
1

1-1. ABOUT THIS MANUAL
Thank you for purchasing our PA-3055 Series System. The PA-3055 is an updated
system designed to be comparable with the highest performance of IBM AT personal
computers. The PA-3055 provides faster processing speed, greater expandability and
can handle more tasks than before. This manual is designed to assist you how to install
a nd set up the whole system. It contains four chapters and two appendixes. Users can
configure the system according to their own needs.
Chapter 1 Introduction
This chapter introduces you to the background of this manual. It also includes
illustrations and specifications for the whole system. The final section of this chapter
indicates some safety reminders on how to take care of your system.
Chapter 2 System Configuration
This chapter outlines the location of motherboard components and their function. You
will learn how to set the jumpers and configure the system to meet your own needs.
Chapter 3 Software
This chapter contains detailed information for driver installations of the Intel®Utility,
VG, LAN, Sound, Touch Screen, embedded peripheral devices, BIOS setup & update,
Watchdog timer and resource map.
Chapter 4 System Diagrams
This chapter shows the exploded diagrams and part numbers of PA-3055 components.

Quarter View
15” LCD & Bezel-free Touchscreen
VFD Customer Display
I/O Port(inside the cover)
Vertical MSR
Angle Adjustor Hinge
Side USB
LED
Ventilation Hold
Power Button

Front View Rear View
Side View
View Bottom View

1-3. SYSTEM SPECIFICATIONS
System
CPU Intel®Celeron®J1900 Quad-Core 2.0GHz
Memory 1 x DDR3 SO-DIMM 204-pin socket, 2GB
OS Support Window Embedded POSReady7
LAN 1 x Giga LAN
Audio 2W speaker & Line-out Port
BIOS AMI SPI BIOS, 8 Mbits with VGA BIOS
RTC Accuracy 3 days 3 seconds
System Weight With power adapter approx. 8.5 kg
Dimension (W x H x D) 390mm x 320mm x 190mm
Viewing Angel 40~80˚
±
Power Supply 120 Watt Power adaptor
Power Consumption (AC):
System
Status
CPU/
HDD/
Memory
VFD
COM & USB
Ports to supply
power of Rear I/O
Consumption
OFF Off 2W
IDLE
Turns on, but
not to execute
extra AP
19.8W
Working 25.6W
without
35.4 W
Full Loading
100% loading
of burn-in test
Runs
new
ticker
USB dummy load
500mA x4

Display
15” TFT XGA LCD Max. Resolution: 1024 x 768
Signal Interface: TTL (24-bit)
Touchscreen 5-wire resistive type
Brightness
Resistive Touchscreen:
Minimum Typical Maximum
160 cd/m2200 cd/m2-
12
3
45
Environment
Temperature Operating: 0~35°C
Storage: -5~60°C
Humidity 20~90%

Optional accessories
MSR ISO I ,II, III; JIS I,II reader
2nd Display 8” LCD (Resolution: 800 x 600)
10.4” LCD (Resolution: 1024 x 768
Customer Display Interface: RS-232C Baud Rate: 9600/19200 bps
Placement: 20 columns and 2 lines, each column is 5
x 7 dots
Brightness: cd/m2
Dimensions:
18.2
107.2
0.55
0.75
6.75
3.75
0.8
1.0
Standard Code
CP-437, CP-850, CP-857, CP-865, Katakana
International Characters
USA, FRANCE, GERMANY, UK, DENMARK I,
SWDEN, ITALY, SPAIN, JAPAN, NORWAY,
DENMARK II, RUSSIA, SLAVONIC

1-4. SAFETY PRECAUTIONS
The following messages are safety reminders on how to protect your systems from
damages, and extending the life cycle of the system.
1. Check the Line Voltage
a. The operating voltage for the power supply should be within the range of
100V to 240V AC; otherwise the system may be damaged.
2. Environmental Conditions
a. Place your PA-3055 on a sturdy, level surface. Be sure to allow enough
space around the system to have easy access needs.
b. Avoid installing your PA-3055 Series POS system in extremely hot or cold
places.
c. Avoid exposure to sunlight for a long period of time (for example, in a
closed car in summer time. Also avoid the system from any heating device.).
Or do not use the PA-3055 when it has been left outdoors in a cold winter
day.
d. Bear in mind that the operating ambient temperature is between 0°C and
35°C (32°F and 95°F).
e. Avoid moving the system rapidly from a hot place to a cold place, and vice
versa, because condensation may occur inside the system.
f. Protect your PA-3055 against strong vibrations, which may cause hard disk
failure.
g. Do not place the system too close to any radio-active device. Radio-active
device may cause signal interference.
h. Always shutdown the operation system before turning off the power.
3. Handling
a. Avoid placing heavy objects on the top of the system.
b. Do not turn the system upside down. This may cause the hard drive to
malfunction.
c. Do not allow any objects to fall into this product.
d. If water or other liquid spills into the product, unplug the power cord
immediately.

4. Good Care
a. When the outside case gets stained, remove the stains using neutral washing
agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the surface of
the case.
c. If heavy stains are present, moisten a cloth with diluted neutral washing
agent or alcohol and then wipe thoroughly with a dry cloth.
d. If dust is accumulated on the case surface, remove it by using a special
vacuum cleaner for computers.

SYSTEM
CONFIGURATION
Helpful information that describes the jumper and connector settings,
component locations, and pin assignment.
Sections included:
External I/O Port Pin Assignment
How to Set Jumpers
Component Locations & Jumper Settings
Mainboard
Printer Board (peripheral device)
VFD Board (peripheral device)
MSR Board (peripheral device)
CHAPTER
2

2-1. SYSTEM EXTERNAL I/O PORT & PIN ASSIGNMENT
Rear I/O
DRW1
USB3
2nd Display
Power
DC IN
COM1
LAN VGA
USB
0
1
2
COM3 COM2
Side I/O
Power USB4
button

Power Button
To turn on the system, press the power button on the side
of the system briefly.
ACTION ASSIGNMENT
Click 0V
Release +3.3V
DC-IN Port
DC IN: DC Power-In Port (rear IO)
PIN ASSIGNMENT PIN ASSIGNMENT
1 GND 3 +24V
2 GND 4 +24V
VGA Port
VGA: VGA Port, D-Sub 15-pin (rear IO)
PIN ASSIGNMENT PIN ASSIGNMENT
1 RED 9 +5V
2 GREEN 10 GND
3 BLUE 11 NC
4 NC 12 DDCA DATA
5 GND 13 HSYNC
6 GND 14 VSYNC
7 GND 15 DDCA CLK
8 GND
34
12
DC IN
Power
Button
15 610 1115
VGA

COM Port
COM1, COM2, COM3:D-Sub9 Serial Ports (rear IO) 
COM1: Co-lay with COM1-1
COM2: Co-lay with COM2-1
COM3: Co-lay with COM3-1
PIN ASSIGNMENT PIN ASSIGNMENT
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI/+5V/+12V
selectable (Max.
current: 1A)
5 GND
LAN Port
LAN: LAN RJ45 Port (rear IO)
PIN ASSIGNMENT PIN ASSIGNMENT
1 MDIP0 5 MDIP2
2 MDIN0 6 MDIN2
3 MDIP1 7 MDIP3
4 MDIN1 8 MDIN3
LAN LED Indicator:
Right Side LED
Yellow Color Blinking LAN Message Active
Off No LAN Message Active
Left Side LED
Green Color On 10/100Mbps LAN Speed Indicator
Orange Color on Giga LAN Speed Indicator
Off No LAN switch/ hub connected.
5
1
9
6
COM1/
COM2/
COM3/
81
Green Yellow
LAN

Cash Drawer Port
DRW1 is used by default. If you need a second port, adopt the method below.
PIN ASSIGNMENT PIN ASSIGNMENT
1 GND 4 +12V/+24V (Max. current: 1A)
2 Drawer Open 5 NC
3 Drawer Sense 6 GND
DRW1
Open Write "700"h to I/O port
"588"h
Close Write "00"h to I/O port
"588"h
USB Port
USB0, USB1, USB2, USB3, USB4: USB Type A Ports
USB0~3: Rear I/O
USB4: Side IO
PIN ASSIGNMENT PIN ASSIGNMENT
1 +5V (Max.
current: 0.5A)
3 D+
2 D- 4 GND
1 4
USB0/
USB1/
USB2/
USB4/
1 4
USB3
DRW1
6 1

2-2. MAINBOARD COMPONENT LOCATIONS & JUMPER
SETTINGS
M/B: PB-6822
LVDS1 USB7 J3
JP_VDD1
JP_12 JP_8 JP_9
USB1
JP32
SW1_3
JP19
JP30
USB2
COM1_1
COM4_1
COM2_1
COM3_1
JP_COM4
JP_COM3
JP_COM2
JP_COM1
PRT_PWR1
PWR_IN1
VGA1
USB8LAN1 LINE-OUT1
JP31
USB4
SW1
USB6
JI_BUTTON1
PS/2_2
SP1
SPK1
SLOT1
COM4_2
JP20 JP21 JP22
COM2
COM3
DC5V_PWR1
JP37
JP29
JP5
DC12V_PWR1
LPT1
J2 SATA2
SATA1
JPWR_4P2
JPWR_4P1
TOUCH3
JP14
JP15
JINVDRV1
JINV4
JP4
JP3
JP38JP39
30
291
2
Battery
1
1
1
1
1 31 4
1
6
5
10
14
1
1
1
11 21 21 2
5 65 65 6
5
2
6
1
1
1
1
1
1
1
2
910
6
1
1
6
1
1
15 15
1
5
1
5
1 15 17 51
2 16 18 52
1
4
1
1
27 8
1
10
5
6
1
6
1
1
1
2
2
5
5
6
5
6
6
1
1
4
1
2
6
10
5
10
5
26
13
14
1
1 4
1 4
1 7
1 7
Intel®
Celeron®J1900
Quad-Core DIMM1
1
2
71
72
73
74
203
204
ESATA1 DRW1
15
PB-6822 Mainboard Component Locations

SLOT2
1
15
17
51
2
16
18
52
PB-6822 Mainboard Component Locations - Rear

COM Port RI & Voltage Selection
JP_COM1, JP_COM2, JP_COM3, JP_COM4: Pin-headers on board
SELECTION JUMPER
SETTING
JUMPER ILLUSTRATION
RI 1-2
5
6
1
2
JP_COM1
5
6
1
2
JP_COM2
5
6
1
2
JP_COM3
5
6
1
2
JP_COM4
+12V 3-4
5
6
1
2
JP_COM1
5
6
1
2
JP_COM2
5
6
1
2
JP_COM3
5
6
1
2
JP_ COM4
+5V 5-6
5
6
1
2
JP_COM1
5
6
1
2
JP_COM2
5
6
1
2
JP_COM3
5
6
1
2
JP_ COM4
Cash Drawer Power Selection
JP29: DRW1'5:'5:
SELECTION JUMPER SETTING JUMPER ILLUSTRATION
+24V 1-2
+12V 2-3
3 1
3 1
JP29
JP29

6
5
4
3
2
1
6
5
4
3
2
1
6
5
4
3
2
1
JP37
GPIO1
GPIO2
DRW1
DRW1-1
(Connect
with
Y-cable)
DRW1-2
JP37: DRW1-2 control connector
SELECTION JUMPER SETTING JUMPER ILLUSTRATION
1-2
1
3
JP37
2-3
1
3
JP37
'5:
'5:
'5:
DRW1
DRW1-2
DRW1-1
DRW1, DRW1-1, DRW1-2: Signal from M/B GPIO (rear I/O)
Step.1
DRW1 includes two groups of
GPIO pins. The second group is
normally unused but can be
enabled by the jumper.
Set the pin-header jumper JP37
as 1-2 connected if necessary.
Step.2
You can split DRW1 into two channels of DRW1-1 & DRW1-2 with
the Y-Cable(optional unit).
DRW1 Extension